Page 1
Installation Instructions Side by Side Refrigerators ZlS360N,ZlSB360D,ZlSW360D ZlSS360N,ZlSS360D ZlS420N,ZlSB420D,ZlSW420D ZlSS420N,ZlSS420D ZIS480N,ZISB480D,ZISW480D ZISS480N,ZISS480D Design 6uide With Installation Instructions Monogram:...
• IMPORTANT- S.,e hese inst uctions installer. Product tailure to improper installation is not covered under tile GE Appliance Warrant)'. for local inspector's use. Obserxe all goxerning codes tile Owner's Manual fl)r warranty infl)rmation. ordinances.
• _&_ter line can enter the opening through the floor YeIlloval. or back wall. The water line should be 1/4" O.D. copper tubing or GE SmartConnect'" kit between 4" minimmn clearance is required when door swing the cold water line and water...
Design Guide FramelessCabinets:The case trim overlaps cabinets atthe top and sides. Therefore, frameless cabinets may require filler strips to prevent interfeence with cabinet door swing. Refrigerator The opening must allow for filler strips. 23-7/8"From Rearof Refrigerator Case Trim 1/4" Top View Door 130 °...
Design Guide FramelessCabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets may Refrigerator require filler strips to CaseTrim prevent interference with cabinet door swing. The opening must allow for filler strips. 23-7/8" FromRearof Refrigerator 1/4" 1/2"...
Design Guide 1/4" FRAMED PANEL DIMENSIONS II _ 5/16" Trim If _ou choose to install fl'amed panels, they must to the dimensions shown. panels will slide Door %ve* into fralne door grille. Non-Dispenser Models If the custom panel is less than 1/4"...
Design Guide 3/4" OVERLAY PANEL DIMENSIONS Overlay Panel Door For a more custom appearance, overlay panels may be installed on trimmed models. overlay panel i/ltlst be secured to a 1/4" thick backer panel which slides into the trim. A spacer panel 0.] 0"...
Design Guide DISPENSER MODELS: RAISED OVERLAY PANEL DESIGN 1/4" Backer .10" SF When a raised panel design is to be used, 3/4" Overlay custom wide middle rail is required to accept dispenser trim. • The middle rail must be wide enough to allow dispenser...
Inchldes 92 flat head screws and 4 endcaps. MATERIALS REQUIRED • 35" long 2x4 tin" Anti-Tip suI)port • 1/4" copper water line tubing or GE SmartCom_ect Refl'igerator Tubing kits • Water shut-off valve (optional but recommended) • Custom panels for doo_...
SUl_ply is required fin" automatic icemaker operation. The water pressure must CopperTubingJ between 40 and 190 p.s.i. OD COl)per or GE SmartConnect • Route l/4" plastic tubing between house cold water line and Shut off the main water supply. the water connection location.
Installation Instructions ISTEP 2AI INSTALLATION WITH I STEP 41 INSTALL ANTI-TIP BRACKETS HOUSEHOLD WATER WARNING: Am,-T,p PRECAUT,ONS FILTRATION SYSTEM refl'igerator is top-heaxy must be secured Skip this step if you do not have a household prexent possibility of tipping forward. water filtration system ATTENTION:PRECAUTIONS COmRE , ES...
Installation Instructions ISTEP 51 LEVEL REFRIGERATOR I STEP 61 ALTERNATE ANTI-TIP PROCEDURE All models have 4-point leveling. The thmt is supported by leveling legs, rear is supported refrigerator must secured to prevent tipping. a_!justable wheels. Both accessible fl'om fl'ont mlti-tip brackets cmmot used...
Installation Instructions ISTEP71 [STEP 9] INSTALL GRILLE PANEL SECURE REFRIGERATOR TO CABINETRY or o_erla) To insert fl'amed panel into the grille: • Raise the grille panel to stop position. _'_ henexer possible, i)erfiwm this step for anti-tip security or when anti-tip brackets cannot...
Installation Instructions ISTEP 101 INSTALL 1/4" FRAMED PANELS Go to Step9Afor OverlayPanels Handle DoorTrim Trim Refrigerator Door Supplied Handle Shown in 1/4"Panel Position Install door panels: Open Phillips • door to 90 °. ]_.elnove tile head screws fl'om tile door handle.
Installation Instructions [STEP 10AI INSTALL OVERLAY PANELS DoorTrim Handle Trim Refrigerator Door Move Forward For3/4" Panel Supplied Handle Shown in Overlay Panel Position Install door panels: Open Phillips • door to 90 °. Relnove tile head screws fl'om tile door handle.
Page 17
Installation Instructions ISTEP 10AI (continued) ISTEP 10AI (continued) Custom Handles • Carefully place the aluminum cover trim into top • If )'ou are using cust(m_ handles, the handle must end cap so that the recess is aligned with the cap. properly secured to the overlay...
See pages 7 and 8 for panel consti tlction infoY/ll ation, GE SmaactCom_ecf'" Tubing: • Insert the molded end of the tubing into refl'igerator connection. Tighten the compression until it is just hand tight.
Installation Instructions lSTEP 15] INSTALL TOEKICK ISTEP 131 CHECK POWER, CLOSE GRILLE PANEL • I,ocate tile supplied toekick (shii)ped taped tile side of tile reflJgerator). Install with 2 screws • Check to be sure power cord is I)lugged,, into provided, at!just to desired height...
Need help?
Do you have a question about the ZlS360N and is the answer not in the manual?
Questions and answers