Kenmore 79045482503 Installation Instructions Manual page 6

Thisrangeis designed t o hangfromthe countertop. I t
doesnotrestonthefloor.
Besurethe bottomof anywallcabinets area minimum
of 30" (76.2cm)above the rangetop area.
Toeliminate the hazard or reaching overheated
surface units,cabinet s torage space located above the
surface unitsshould beavoided. If cabinet s torage isto
beprovided, the hazard canbereduced by installing a
range hoodthatprojects h orizontally a minimum of 5"
(12.7cm)beyond thebottomfrontedge ofthe
cabinets.
ImportantNote: Doorremoval isnot a requirement for
installation o f the range, b utisanadded convenience.
See oven door removal
instructions in the Use
and Care Guide.
I. Install base cabinets 30" (76.2 cm) apart, and be
sure they are plumb and level before attaching to
cou ntertop.
2. Cut countertop exactly as shown in Figure 1. Shave
raised edge level to clear 31 I/2" (81 cm) wide rim
on rolled edge styled countertops.
3. Install the wiring junction box in an adjoining
cabinet or under the floor (range has 48"/122 cm of
conduit). Cut 1-1/4" (3.2 cm) hole to bring conduit
to the junction box.
4. To provide an optimum installation, the top surface
of the countertop must be level and flat (lie on the
same plane) around the 3 sides that are adjacent to
range cooktop. Proper adjustments to make the top
flat should be made or gaps between the
countertop may occur.
5. _ To reduce the risk of damaging your
appliance, do not handle or manipulate it by the
ceramic glass. Manipulate with care.
6. Move range in front of cabinet opening.
7. Push the electric conduit through the hole and
attach it to the junction box. Leave enough slack in
the conduit to allow the range to be pulled forward
several inches for service if necessary.
8. Oven door is heavy. It is advisable to remove
door and eliminate its weight as range is lifted
into position. See oven door removal
instructions in the Use and Care Guide. Lift the
range into position on the countertop and
make sure the appliance is centered in the
cutout opening to be sure that the flanges of
the upper side panel are sitting on the
countertop to avoid glass breakage.
Ranges with Ceramic Glass Cooktop
9. This range is equipped with an anti-tip bracket
attached to the back of the range with two screws.
If countertop thickness is greater than I/2" (1.3 cm),
relocate anti-tip bracket to the lower position 1/4"
(6.4 mm) below (see Figure I, on page I).
10.Anti-slide brackets Installtion (Figure 6):
1. Place the range so that it is about 6" ou of the
cabinet.
2. Insert from below the shoulder screws in the side
panel (one on each side)
3. Slide the range into its final position.
4. Position the "L" bracket against the side of the
Figure 6
cabinet so that it is retained by the shoulder
screws, hold bracket and mark the holes on the
inside of the cabinet. Drill pilot holes into cabinet
where you just marked (Caution should be take to
avoid drilling throught the opposite side of the
cabinet). Attach the "L" bracket to the cabinet
with the screws provided (don't forget to insert the
shoulder screw into the bracket).
5. Repeat steps 4 on the other side.
11. Install the decorative lower trim under the door using
the screws provided with the range.
Ranges with a lift-up cooktop
9. Anti-tip/anti-slide screws installation:
I. Slide the range to its final postion.
2. Lift the cooktop and secure range burner box to
cabinet with screws supplied to prevent range
from tipping (Figure 7).
10. Install the decorative lower trim under the door using
the screws provided with the range.