Godex EZ-DT-2 User Manual
  1. Manuals
  2. Brands
  3. Godex Manuals
  4. Printer
  5. EZ-DT-2
  6. User manual

Godex EZ-DT-2 User Manual

Barcode printer
Hide thumbs Also See for EZ-DT-2:
Table of Contents

Advertisement

Quick Links

See also: User Manual
User's Manual
EZ-DT-2 / EZ-DT-4
P/N. 920-012511-00
Rev. C, 03.2007

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EZ-DT-2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Godex EZ-DT-2

Summary of Contents for Godex EZ-DT-2

  • Page 1 User’s Manual EZ-DT-2 / EZ-DT-4 P/N. 920-012511-00 Rev. C, 03.2007...

  • Page 2: Safety Instructions

    Bei Wartungs- und Reparaturarbeiten müssen die Sicherheitsvorschriften der zuständigen Berufsverbände und Behörden unbedingt eingehalten werden. Bei Verletzungen unbedingt den Arzt aufsuchen und die gegebenenfalls die zuständigen Stellen benachrichtigen. Unterlassung kann zum Verlust der Versicherungsleistungen führen. EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...
  • Page 3 CAUTION Danger of explosion if battery is incorrectly replaced Replace only with the equivalent type recommended by the manufacture. Dispose of used batteries according to the manufacturer’s instructions. EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...
  • Page 4 EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...
  • Page 5 EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...
  • Page 6 EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...
  • Page 7 EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...
  • Page 8 EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...
  • Page 9 EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...
  • Page 10 EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...
  • Page 11 EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...

  • Page 12: Table Of Contents

    4-7. Error Messages......................32 5. MAINTENANCE AND ADJUSTMENT ........33 5-1. Print Head Module Installation / Removal Instruction........... 33 5-2. Thermal Print Head Cleaning ..................35 5-3. Adjust the Cutter ......................35 5-4. Troubleshooting ......................36 EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...

  • Page 13: Barcode Printer

    Windows bit mapped font: can be rotated in 8 orientations and expandable 8 times horizontally and vertically. Fonts Download Asian font: can be rotated in 4 orientations and expandable 8 times horizontally and vertically. True Type Font: can be rotated in 4 orientations. EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...
  • Page 14 Width: 168 mm (6.61”) Weight: 1.2 Kg Weight: 1.5 Kg Rotary Cutter Module Rotary Cutter Module Stripper Module Stripper Module Options Internal Ethernet Adapter Card Internal Ethernet Adapter Card Parallel port Specifications are subject to change without notice. EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...

  • Page 15: Communication Interface

    +5V,max 500mA PRINTER Note The total current output from serial port can not exceed 500mA. USB Interface Connector Type : Type B PIN NO. FUNCTION VBUS Internal Interface UART1 wafer Ethernet module E_MD E_MD E_RST E_RST EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...

  • Page 16: Printer Parts

    1-4. Printer Parts LED Light FEED Key Top Cover Power Switch Cover Open Button Print Head Lift Label Roll Holder Print Mechanism Label Roll Core Label Guide Front Cover Piece EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...
  • Page 17 Platen Cover Label Sensor Platen Roller Power Socket USB Port Fan-Fold Label Insert Serial Port (RS-232) Bottom Case Cover Hang Holes EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...

  • Page 18: Printer Installation

    Roll Core upward. Place a new label roll onto the Label Roll Core. Flip the Label Roll Core downward and pull back the Label Roll Holder. Pull and lock the Label Roll Core to the original position. EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...
  • Page 19 Put the label under the Label Guide and stretch it frontward. Pull the Label Guide inward and make it fit the edge of label. Close the Top Cover to complete the label installation. EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...

  • Page 20: Label Roll Core Switch

    When the lock hole of Label Roll Core is on lower side, it applies to 1.5” core. Note You can also distinguish it by the index on the Label Roll Core as shown in figure. 1.5” Core EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...

  • Page 21: Pc Connection

    Connect the cable to the USB/ Serial port on the printer and on the PC. Power on the printer and the LED light will shine. EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...

  • Page 22: Driver Installation

    Insert the product CD, select ‘Specify a location’ and describe the path of the printer driver. Follow the instruction on the Window and complete the driver installation. EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...

  • Page 23: Accessory

    Piece. Note You can also use coin or screwdriver to open the Front Cover Piece. Push the Stripper connector into printer through the cable hole as shown in figure. Place the Stripper on the fillister. EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...
  • Page 24 Before plugging the connector into socket, please check the pin first. Lock the Bottom Case Cover. Turn the printer back to proceed to the label installation. EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...
  • Page 25 13. Follow the direction as shown in figure to feed the liner across the stripper. 14. Flip the stripper upward to close it. 15. Press the FEED key to adjust the position of label and complete the installation. EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...

  • Page 26: Cutter

    Place the printer on a horizontal surface and open the Top Cover. Remove the Front Cover Piece. Push the Cutter connector into printer through the cable hole as shown in figure. Place the Stripper on the fillister. EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...
  • Page 27 Before plugging the connector into socket, please check the pin first. Lock the Bottom Case Cover. Turn the printer back to proceed to the label installation. 10. Follow the instruction on Chapter 2-1 to install the label. EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...
  • Page 28 11. Feed the label through the Cutter and press the FEED key to complete the installation. EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...

  • Page 29: Control Panel

    When printing with labels, pressing the FEED key will feed one label at a time. If the label is not sent out in a correct position, please proceed with the Auto sensing (see page30). EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...

  • Page 30: Self-Test

    See-through Sensor: OFF Reflective Sensor status Reflective Sensor AD : 146 186 223 (2) Code Page Code Page: 850 Self-Test includes the internal printer data setting. Self-Test includes the internal printer data setting. EZ-DT-2/EZ-DT-4 User’s Manual Rev. C Rev. C...

  • Page 31: Auto Sensing

    To cancel (get out of the Dump Mode), press the FEED key, the printer will automatically print out “OUT OF DUMP MODE”. This indicates that printer is back in the standby mode. Powering off the printer is another way to exit the Dump Mode. EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...

  • Page 32: See-Through Sensor On/Off

    4-6. See-through Sensor on/off 4-6. See-through Sensor on/off There are two types of sensor in EZ-DT-2 / EZ-DT-4 printer - Reflective Sensor and See-through There are two types of sensor in EZ-DT-2 / EZ-DT-4 printer - Reflective Sensor and See-through Sensor.

  • Page 33: Error Messages

    “Filename can not be found.” the file exist and the names are correct. File name is repeated; printer will Change the file name and 2 beeps twice print out “Filename is repeated.” download again. EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...

  • Page 34: Maintenance And Adjustment

    Flip the Print Head Lift downward to release it. The Print Head Bracket can be flipped downward after Print Head Lift is released. Remove the Print Head Connector. EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...
  • Page 35 After new print head is installed, tighten the Print Head Screws, plug the Print Head Connector, restore the Print Head Bracket and lock the Print Head Lift to complete the installation. EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...

  • Page 36: Thermal Print Head Cleaning

    Use screwdriver to turn the Cutter Adjustment Screw counter-clockwise for releasing the paper-knife of the cutter and then remove the jammed-label out. After the jammed-label is removed, turn the Cutter Adjustment Screw clockwise to restore the paper-knife. EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...

  • Page 37: Troubleshooting

    Check if stripper sensor is covered with dust working correctly. Check if label is installed properly Note Your dealer is knowledgeable about GODEX printers, printing software, and your unique system. Please contact your local dealer for further technical support. EZ-DT-2/EZ-DT-4 User’s Manual Rev. C...

This manual is also suitable for:

Ez-dt-4

Table of Contents