Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Godex EZ-2P
Summary of Contents for Godex EZ-2P
- Page 1 P/N. 920-010311-00 Edition 0 JUN. 19 EZ-2P/4P User's Manual PDF created with FinePrint pdfFactory trial version http://www.fineprint.com...
-
Page 2: Table Of Contents
EZ-2P/EZ-4P SERIES PRINTER ... 2 1. A BOUT THE RINTER 1-1. Introduction..2 1-2. General Specifications .... 2 1-3. Contents .... 3 1-4. EZ2P/4P Page mode Printer Parts..3 2. S ETTING UP THE 2-1. -
Page 3: Ez-2P/Ez-4P Series Printer
2” print width direct thermal label printer. Applications: P.O.S. printer, Electronic Scale printer, Data recorder, Ticket printer...etc. EZ-2PC EZ-2P with paper cutter. Cutter life expectancy 100,000 cuts. EZ-2PS EZ-2P with Auto Label Stripper.(Label on Demand) B. 4” Printer model description EZ-4P 4”... -
Page 4: Contents
Label guide 10 Label spindle hole 11 Stands for big roll of label The big label roll holder stands 12 Parallel printer connector The printer port connector 13 Serial interface connector Connect with host serial port 14 Power jack 15 Power switch... -
Page 5: Setting Up The Printer
1. Be sure the power is off. 2. Plug the power adapter into the printer power jack. 3. Connect the printer to an interface (parallel or serial port) 4. Power on. The LED light will be red or green. PDF created with FinePrint pdfFactory trial version 2.1.1) -
Page 6: Replacing The Label Roll
2. Remove the front cover and the back cover. 3. Remove the label roll and the label spindle. 4. Place the printer facedown. Loose the four corner screws in the hollow. 5. Remove the mechanism assembly (see figure 2.4.1.). 6. Facing the PC Board (the board with RS-232 port), around the bottom of the left side there locates JUMP1, 2*8 pin-set. -
Page 7: Self Test
2-5. Self Test The self-test function helps you check if the printer works correctly. To use the self-test function; please follow these steps. 1. Load the paper. 2. Hold down the feed button when powering on. 3. Release the feed button. Wait a minute, the printer will print the self-test contents. -
Page 8: Maintenance And Adjustments
3. Maintenance and Adjustments 3-1. How to clean the printer head 1. Remove the top cover. 2. Press your finger on Retainer bracket, move out the two Fasteners from the Retainer bracket, and take out the Retainer bracket and the print head unit. - Page 9 If you are using thermal label paper 1. Remove the label from the liner. Load the liner paper under the sensor. 2. Slowly adjust the Variable resistor and press the paper feed switch (at least 7 times), until the LED light turns red.
-
Page 10: Stripper And Cutter
How to use stripper The label sensor is hidden inside the top cover. This sensor keeps the printer from printing the next label until you remove the previously stripped label. The liner paper is going out from the liner output bar. Please follow these steps. - Page 11 5. Place back the top cover. The printer is ready to print. When you start to print the label, the label will auto-strip from the liner paper. The printer will wait to print until the printed label has been taken away (see figure 4.2.2c).
-
Page 12: Appendix A. Troubleshooting
Remove the caught label. Make sure the width and thickness of label is within the specification. Clean printer head with alcohol (If the label glue is attached to printer head, please apply alcohol to printer head, wipe with soft cloth softly).