Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Gefen 6x2 HDMI
Summary of Contents for Gefen 6x2 HDMI
- Page 1 6x2 HDMI Switcher U S E R M A N U A L www.gefen.com...
- Page 2 Notice Gefen Inc. reserves the right to make changes in the hard ware, packaging and any accompanying doc u men ta tion without prior written notice. 6x2 HDMI Switcher is a trademark of Gefen Inc. HDMI is a trademark of hdmi.org...
-
Page 3: Table Of Contents
TABLE OF CONTENTS Introduction Features Front Panel Description Back Panel Description Connecting and Operating the 6x2 HDMI Switcher RMT-6IR Installation IR Code Confi guration EDID Management Feature EDID Management Modes RS-232 Serial Control RS-232 Serial Control Commands Rack Mount Diagram Specifi... -
Page 4: Introduction
Our Commitment Gefen will always offer the fi nest quality product at the best possible price. Included in that price is a lifetime support from a team of outstanding engineers. The Gefen 6x2 HDMI Switcher allows six HDTV HDMI devices to be switched easily in to two HDTV HDMI compatible monitors or projectors. -
Page 5: Features
• Inputs can be switched with the IR remote control, contact closure controller or through the RS232 connector. • Installs in seconds Includes: (1) 6x2 HDMI Switcher (6) 6’ HDMI cables (M-M) (1) 24VDC Power Supply (1) RMT-6IR (1) Rack Ears... -
Page 6: Front Panel Description
FRONT PANEL DESCRIPTIONS... -
Page 7: Back Panel Description
BACK PANEL DESCRIPTIONS... -
Page 8: Connecting And Operating The 6X2 Hdmi Switcher
How to Connect the 6x2 HDMI Switcher to your devices 1 Connect the supplied cables from the HDTV sources into the 6x2 HDMI Switcher inputs. 2 Connect the cable from your display (monitor or projector) into the HDMI outs of the 6x2 HDMI Switcher. -
Page 9: Rmt-6Ir Installation
RMT-6IR INSTALLATION 1. Remove battery cover from the back of the RMT-6IR remote. 2. Verify that dip switches 1 & 2 are in the down (OFF) position. 3. Insert the battery, hold the battery so that you can see the positive side facing up. The side that is not marked must be facing down. -
Page 10: Ir Code Confi Guration
IR CODE CONFIGURATION Why would I need to change the remote channel? In some instances, the 6x2 Switcher for HDMI may use IR codes that confl ict with other IR remote control devices. The unit may switch inputs when another brand IR remote control is used or the RMT-6IR may cause other brand IR controlled devices to behave unexpectedly. -
Page 11: Edid Management Feature
EDID MANAGEMENT FEATURE EDID. What is it and what is it used for? Under normal circumstances, an source device (digital and analog) will require information about a connected device/display to assess what resolutions and features are available. The source can then cater its output to send only resolutions and features that are compatible with the attached device/display. -
Page 12: Edid Management Modes
EDID MANAGEMENT MODES v. 2015 EDID Modes The diagram below illustrates the 8 DIP switch bank. DIP SWITCH Function EDID Mode EDID Mode IR Channel IR Channel EDID Mode EDID Mode Use DIP switches 1, 2, 5, and 7 to select the desired EDID management mode. EDID Mode 0 (Switch 1=OFF Switch2=OFF Switch5=ON) •... - Page 13 RS-232 SERIAL COMMUNICATION What features are available via the RS-232 serial communications port? The 6x2 Switcher for HDMI can accept commands through the RS-232 serial communications port located on the rear panel. The current RS-232 control features are: • Switching/routing of inputs to outputs without the RMT-6IR remote control. •...
- Page 14 RS-232 SERIAL COMMUNICATION COMMANDS Switching/Routing Binary Table ASCII RMT-6IR Binary Button 0011 0001 0011 0010 0011 0011 0011 0100 0011 0101 0011 0110 EDID Management Modes All DIP switches inside the unit must be in their default OFF position. Use the ASCII commands below to change the EDID modes.
-
Page 15: Rack Mount Diagram
6x2 HDMI SWITCHER RACK MOUNT DIAGRAM... -
Page 16: Specifi Cations
SPECIFICATIONS Video Amplifi er Bandwidth ................. 1.65 GHz Input Video Signal ..................1.2 volts p-p Input DDC Signal ..................5 volts p-p (TTL) Single Link Range ................1080p / 1920 x 1200 Input Connector Type ....................HDMI Output Connector Type ....................HDMI Output Audio Connector Type.................