Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Kruger Alto S
Summary of Contents for Kruger Alto S
- Page 1 USER MANUAL ALTO ALTO • & • ENGLISH GETTING STARTED...
- Page 2 Thank you for choosing Krüger home appliances! Please follow the recommendations and guidelines contained in this manual. This way the appliance will give you consistent high performance and ef ciency for many years to come. Table of Contents Warnings & Caution Characteristics Installation &...
- Page 3 WARNING TO REDUCE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, PLEASE OBSERVE THE FOLLOWING: Installation work and electric wiring must be done by a quali ed professional in accordance with local applicable codes and standards, including re-rated construction. The stainless steel structural housing may have sharp edges.
-
Page 4: Installation & Usage
CHARACTERISTICS Dimensions 5 1/4” 28 1/4” 11 3/4” 7” 22 1/4” INSTALLATION & USAGE NOTE: Carefully remove the blue coloured plastic protective lm prior to nal installation. Description / Connection This appliance should be mounted to the bottom of a standard wall cabinet. If the hood must be mounted directly to the wall, secure the hood to wall studs. -
Page 5: Location Preparation
Location Preparation Use the dimensional drawings above to lay out the range hood’s mounting holes, wiring access and ductwork. Mark the cabinet bottom and drywall where applicable. Make a cutout for the wiring and duct work. Install the ductwork so that it is ush with the range hood’s mounting surface. Run two conductor wires from a power source to the hood location. -
Page 6: Hood Preparation
Hood Preparation Remove the bottom panel of the hood by removing its 7 mounting screws. Set aside the bottom panel once it has been removed. Remove the wiring knock-out located at the top of the unit. Depending on the type of exhaust options you would like to go with. - Page 7 6” Circular Duct Installation • Mount the 6” round duct on the top of the hood. Uses 10 screws. Seal with duct tape when nished. 3 ¼” x 10” Rectangular Duct Installation • Mount the 3¼” x 10” duct onto the top of the hood. Uses 5 Screws. Seal with duct tape when nished.
-
Page 8: Hood Installation
• Install the adaptor to the back of the hood, using 6 screws. Hood Installation Insert the power cable in the hood and tighten the wire clamp to screw in the cable. Align the hood’s keyhole mounting slots over the 4 partially installed screws. Making sure the duct positions over the hood’s duct adaptor, push the hood against the rear wall. -
Page 9: Operation
LIGHTING The range hood requires two type JCD, 12V, 20W max, G-4 base, halogen bulbs. WARNING: Always switch off the electrical supply before carrying out any operation or maintenance on the appliance. Remove the halogen bulb cover with a athead screw driver. Remove the bulb by pulling it out of its socket horizontally. -
Page 10: Operation Instructions
INTELLICLEAN™ AUTOMATIC CLEANING SYSTEM A detergent tank is integrated into the structure of the range hood and a pump will automatically distribute cleansers onto both fans inside the unit when the INTELLICLEAN™ button is pushed. Cleaning often can keep the inside of the rangehood clean and prolongs the life of the unit. Operation Instructions Pour both cleanser and water to the marked level on the provided re ll container. -
Page 11: Maintenance And Cleaning
MAINTENANCE & CLEANING NOTE: Before servicing or cleaning unit, switch power off at the service panel. This will prevent power from being switched on accidentally. Follow these steps below to clean the fans manually Disengage the small grease guard cups from the lters by turning them counter-clockwise. Remove the screw holding the lters in place. - Page 12 ALTO™ and KRÜGER ZENISS™ are all subsidiary development branches of KRÜGER™ electrical appliances LTd. © 2011 All rights reserved. For more information on how to care for your kitchen ventilation unit, please contact us at www.krugerliving.com...