Table of Contents
Advertisement
Programming System Features
The System Features Learn Routine dictates how the unit operates. It is possible to access and change most of the
feature settings using the Valet button.
1.
Turn the ignition on, then off.
2.
Select a Menu. Press and hold the Valet button. The number of LED flashes and horn honks indicates the
menu number. A single LED flash and honk indicates menu 1. Two LED flashes and 2 honks indicates menu
2.
3.
When the desired menu LED flashes and honks are heard, release the Valet button.
4.
Select a Feature. Press and release the Valet button the number of times corresponding to the feature you
wish to change. Then press and hold one more time to select the feature. The LED flashes and the horn
honks to indicate which feature is selected.
Program the Feature. While holding the Valet button, you can program the feature using the remote
5.
control.
For features with only two options;
= option 1 while
= option 2.
For features with more than two options;
selects the options in ascending order.
The LED flashes and the horn honks indicating which option is selected.
Once a feature is programmed:
Other features can be programmed within the same menu
Another menu can be selected
The learn routine can be exited if programming is complete
To access another feature in the same menu:
1.
Press and release the Valet button the number of times necessary to advance from the feature you just pro-
grammed to the next one you want to program.
2.
Then press the Valet button once more and hold it.
To select another menu:
1.
Press and hold the Valet button.
2.
After 3 seconds, the unit advances to the next menu, the horn honks and LED flashes indicating which menu
has been accessed.
The learn routine exits if any of the following occurs:
The ignition is turned On
There is no activity for 30 seconds
The Valet button is pressed too many times
Bitwriter - Only Options
If programming with the Bitwriter®, the learn routine can be locked or unlocked. If the learn routine has
previously been locked, it must be unlocked with Bitwriter® - this cannot be done manually with the Valet
button.
The Bitwriter®
gives you access to a wider range of system options. These features and the adjustments that
may be programmed are described in the table below.
Menu Item
Feature
Default
1
Engine Runtime
12 min.
2
Diesel start type
Off
3
Diesel start delay time (seconds)
15 sec
4
Virtual Tach Fine Tune
Not initialized
5
Remote control programming
Unlocked
6
Feature Programming
Unlocked
© 2013 Directed. All rights Reserved.
Feature Menus
Default settings are in bold type.
Menu 1
Feature #
Feature
Opt. 1
1
Horn function
Off
2
Ignition con-
On
trolled lock
3
Ignition con-
On
trolled unlock
4
Doorlock out-
0.8 sec.
put duration
5
Double pulse
Off
unlock
Off
6
Double pulse
lock
7
Factory Alarm
with unlock
Disarm func-
tion
8
Factory Alarm
Single
Disarm Pulses
9
Comfort
Comfort
Closure
Closure 1
10
Panic
On
Menu 2
Feature #
Feature
Opt. 1
1
Engine check-
Virtual tach
ing
12 min
2
Engine
Runtime
3
Park light
Pulsed
output
4
Cranking time
0.6 sec.
5
Activation
1 pulse
pulse count
6
2nd Ignition
Ignition
behavior
Options
7
Accessory
Off during
output
wait-to-start
1-60 min.
8
2nd Status
Normal
Timed
behavior
1-90 sec.
9
Anti-grind
On
0 to 1 second in 50 mil-
10
Diesel start
Off
lisecond increments
delay
Locked
11
Timer mode
12 min
Locked
run time
Remote Programming
1.
2.
3.
Opt. 2
Opt. 3
Opt.4
Opt. 5+
4.
5.
Siren
Siren
Siren
Siren
6.
20 mS
30 mS
40 mS
50 mS
7.
Off
The programming routine exits if any of the following occurs:
The ignition is turned off
Off
There is no activity for 30 seconds
The Valet button is pressed too many times
3.5 sec.
0.4 sec.
On
Basic Remote Functions
On
ICON
Before unlock
Remote start
only
Double
Off
Comfort
Closure 2
AUX
Off
Note: See Owner's guide for more details
Opt. 2
Opt. 3
Opt.4
Opt. 5+
voltage
Off
tachometer
24 min
60 min
Constant
0.8 sec.
1.0 sec.
1.2 sec.
1.4,
1.6,
1.8,
2.0,
4.0 sec
2 pulses
3 pulses
Accessory
On during
wait-to-start
Latch rear
Pulse rear
defogger
defogger
Off
Timed 15 sec
Timed 30 sec. Timed 45 sec.
3 min
6 min
9 min
Turn key to the ON position
Within 5 seconds, press and release Valet button one time.
Within 5 seconds, press and hold the Valet button. The LED will flash one time and the horn honks to confirm
entry into remote programming.
Press the
button on the remote control.
The horn honks to confirm the remote has been programmed.
Release the Valet button, and turn the key to the Off position.
The horn sounds one long honk to confirm that remote programming has been exited.
BASIC
DESCRIPTION
COMMANDS
Pressing for one second locks the system (if the door locks are connected)
LOCK
Pressing for one second unlocks the doors (if connected)
UNLOCK
REMOTE START
Press to remotely start and run the vehicle for a pro gram ma ble period of time
or press to turn off if vehicle is already remote started
SILENT MODE/AUX-
Silent Mode works by pressing this button for less than one second before
ILIARY FUNCTION
locking or unlocking. This button can also be used for an optional auxiliary
function such as trunk release
Guide Translations
For a Spanish or French version of the Installation Guide, please download it
from www.directechs.com under "Resources".
Traducción de los manuales:
Para obtener una versión en Español o Francés del Manual de Instalación,
descárguela de www.directechs.com bajo el título "Recursos" ("Resources").
Traduction du guide:
Pour une version française ou espagnole du guide d'installation, veuillez le té-
lécharger à www.directechs.com sous «Resources».
Bitwriters with a date code of 6a or older require an IC
upgrade (p/n 998M). Some bitwriters with a date code
of 6B do not require the IC upgrade, refer to tech tip #
1112 for more information.
See full Installation Guide for more
detailed information on this sys-
tem. More can be found online at:
www.directechs.com
The Bitwriter® (p/n 998U)
requires chip version 2.7 or
newer to program this unit.
QRN4105DP 2013-06
2
Hide quick links:
Advertisement
Table of Contents
