Table of Contents
Advertisement
HKTS200SUB Rear-Panel Connections
1
2
3
4
5
6
7
8
9
Subwoofer Level Control:
Use this control to adjust the HKTS200SUB's volume. Turn
clockwise to increase the volume; turn counterclockwise to decrease the volume.
Bass Boost Switch:
Set this switch to ON to enhance the HKTS200SUB's low-frequency
1
performance. Set this switch to OFF for normal low-frequency performance.
Phase Switch:
The Phase Switch
2
action moves in and out in phase with the satellite speakers. If the subwoofer were
to play out of phase with the satellite speakers, the sound waves produced by the
subwoofer could be canceled out, reducing bass performance and sonic impact. This
phenomenon depends in part on the relative placement of all the speakers in the
room. In most cases the Phase Switch
However, it does no harm to experiment, and you can leave the Phase Switch
the position that maximizes bass response and impact.
Power On Mode Switch:
When set in the AUTO position and when the Power Switch
3
is set to ON, the HKTS200SUB will automatically turn itself on when it receives an
7
audio signal, and will enter the standby mode once no audio signal has been received
for about 15 minutes. When this switch is set in the ON position, the HKTS200SUB
will remain on whether or not it is receiving an audio signal.
An LED on the HKTS200SUB's top panel indicates whether the subwoofer is in the on
or standby state:
• When the LED is illuminated white, the HKTS200SUB is turned on.
• When the LED is not illuminated, the HKTS200SUB is in standby mode.
When the Master Power Switch
illuminated, no matter what setting the Power On Mode Switch
External Trigger Input:
Use the mini-plug of the supplied combination LFE and trigger
4
cable to connect the External Trigger Input to the trigger output of another
compatible component. Whenever a trigger signal between 3 and 30V (AC or DC) is
detected, the HKTS200SUB's amplifier will turn on. The HKTS200SUB's amplifier will
turn off after the trigger signal ceases. (This will occur even when the Power On
Mode Switch
is in the AUTO position.)
3
determines whether the HKTS200SUB's piston-like
2
should be left in the NORMAL position.
2
is set to OFF , the LED will not be
7
is in.
3
PL0004-01001
Line-Level LFE In Connector:
5
LFE and trigger cable to connect the Line-Level LFE In to the dedicated subwoofer
output of a receiver or preamp/processor. This input bypasses the HKTS200SUB's
internal crossover circuitry, so it should only be used with a subwoofer output that has
been low-pass filtered. If your receiver or preamp/processor does not have a dedicated
subwoofer output that is low-pass filtered you should use the HKTS200SUB's Line-
Level L/R In Connectors
Line-Level L/R In Connectors:
6
does not have digital surround sound decoding or a subwoofer output that is low-pass
filtered.
in
2
• If your receiver or preamp/processor has a separate subwoofer output, use the LFE
(purple) connector of the supplied combination LFE and trigger cable to connect it to
either one of the HKTS200SUB's Line-Level L/R In Connectors.
• If your receiver or preamp/processor does not have a separate subwoofer output,
use two Y-adapters (not supplied). Connect an adapter's single end to the unit's
preamp output for that channel. Connect one of the adapter's dual ends to the main
amp input for that channel, and connect the adapter's other dual end to one of the
HKTS200SUB's Line-Level L/R In Connectors. Repeat with the other Y-adapter,
preamp channel, main amp input and HKTS200SUB Line-Level L/R In Connector.
Power Switch:
Set this switch in the ON position to turn the HKTS200SUB on. The
7
subwoofer will then either be on or in standby mode, depending on the setting of the
Power On Mode Switch
Power Cord (Non-Detachable):
8
and speaker connections described in this manual, plug this cord into an active,
unswitched electrical outlet for proper operation of the HKTS200SUB. DO NOT plug this
cord into the accessory outlets found in some audio components.
4 4
Use the LFE (purple) connector of the supplied combination
instead.
6
Use these connectors if your receiver or preamp/processor
.
3
After you have made and verified all subwoofer
Hide quick links:
Advertisement
Table of Contents
