Pico Macom SIRD-FTA-2 Owner's Manual page 19

PICO MACOM
• When you press [Yellow], a safety question will be displayed for
confirmation to delete all transponders or not. If you select "OK", the all
transponders on current satellite will be deleted.
3. For existing transponders, you can use number buttons to modify the pa-
rameters of "TP Frequency" and "Symbol Rate" or [VOLt/u] to change
the value directly. "Polarity" and "FTA only" are used for setting scan
conditions. Press [VOLt/u] to select a different mode.
On "TP Scan" item, press [OK] to open another window where you can set
"Scan Mode", "Program Type" and "NIT Search". Press [Menu/Exit] to re-
turn to the previous menu.
Press [Red] button to add a new TP.
Press [Green] button to delete the current TP.
Press [Yellow] button to delete all transponders on current satellite.
4. Antenna Setup: Press [OK] to enter LNB configuration, as shown beside:
• LNB Type: Press [VOLt/u] to switch among "Standard", "User" and
"Universal" mode.
For Example: If you use a Dual LNB, you should select "User"
option in "LNB Type" and set the correct frequency in LNB type.
• 22K: Use [VOLt/u] to switch "ON" and "Off". The 22KHz signal is
used in KU universal LNBs to change between low band and high
band.
! Notice: After choosing LNB type, "Universal", you cannot modify 22K.
• DiSEqC1.0: Use [VOLt/u] to switch the options or press [OK] to open
the DiSEqC1.0 option list to select directly with [CHp/q], press [OK] to
confirm it.
• DiSEqC1.1: Use [VOLt/u] to switch DiSEqC1.1 option or press [OK]
to enter DiSEqC1.1 option to select directly with [CHp/q], press [OK]
to confirm it. The options of this item are: Disable / CCard1 M1 Port1
/ CCard1 M1 Port2 / CCard1 M1 Port3 / CCard1 M1 Port4 / CCard1
M2 Port1 / CCard1 M2 Port2 / CCard1 M2 Port3 / CCard1 M2 Port4 /
CCard1 M3 Port1 / CCard1 M3 Port2 / CCard1 M3 Port3 / CCard1 M3
Port4 / CCard2 Port1 / CCard2 Port2 / CCard2 Port3 / CCard2 Port4 /
CCard2 Port5 / CCard2 Port6 / CCard2 Port7 / CCard2 Port8 / CCard2
Port9 / CCard2 Port10 / CCard2 Port11 / CCard2 Port12 / CCard2
Port13 / CCard2 Port14 / CCard2 Port15 / CCard2 Port16.
• Positioner: Press [VOLt/u] to select between "Off / DiSEqC1.2 /
USALS".
!Notice: When you select "DiSEqC1.2 or USALS", "DiSEqC1.0" and
"DiSEqC1.1", items will be disabled.
• Polarity: Press [VOLt/u] to switch between "Auto / H / V ".
• Toneburst: Press [VOLt/u] to switch this function "On" or "Off".
5. After you completed your modification on the "TP Scan" item, press [OK]
twice to start scanning.
CONTACT US 858.546.5050
SIRD-FTA-2
4.3
www.picomacom.com
19