Single Search - Pico Macom SIRD-FTA-2 Owner's Manual

PICO MACOM

4.1 Single Search

After selecting "Single Search", you will see a window as shown beside:
1. In the "Satellite" item, press [VOLt/u] to select the satellite that you want
to scan or press [OK] to open the "satellite list" to select directly with
[CHp/q], press [OK] to confirm it.
2. LNB Configuration: Press [OK] to enter LNB configuration, you will see a
window as shown beside:
• LNB Type: Press [VOLt/u] to switch among "Standard", "User" and
"Universal" mode.
For Example: If you use a Dual LNB, you should select "User" option in
"LNB Type" and set the correct frequency in LNB type.
• 22K: Use [VOLt/u] to switch "ON" and "Off". The 22KHz signal is
used in KU universal LNBs to change between low band and high
band.
! Notice: After choosing LNB type "Universal", you cannot
modify 22K.
• DiSEqC1.0: Use [VOLt/u] to switch the options or press [OK] to open
the DiSEqC1.0 option list to select directly with [CHp/q], press [OK] to
confirm it.
• DiSEqC1.1: Use [VOLt/u] to switch DiSEqC1.1 option or press [OK]
to enter DiSEqC1.1 option to select directly with [CHp/q], press [OK]
to confirm it. The options of this item are: Disable / CCard1 M1 Port1
/ CCard1 M1 Port2 / CCard1 M1 Port3 / CCard1 M1 Port4 / CCard1
M2 Port1 / CCard1 M2 Port2 / CCard1 M2 Port3 / CCard1 M2 Port4 /
CCard1 M3 Port1 / CCard1 M3 Port2 / CCard1 M3 Port3 / CCard1 M3
Port4 / CCard2 Port1 / CCard2 Port2 / CCard2 Port3 / CCard2 Port4 /
CCard2 Port5 / CCard2 Port6 / CCard2 Port7 / CCard2 Port8 / CCard2
Port9 / CCard2 Port10 / CCard2 Port11 / CCard2 Port12 / CCard2
Port13 / CCard2 Port14 / CCard2 Port15 / CCard2 Port16.
• Positioner: Press [VOLt/u] to select between "Off / DiSEqC1.USALS"
! Notice: When you select "DiSEqC1.2 or USALS", "DiSEqC1.0" and
"DiSEqC1.1" items will be disabled.
• Polarity: Press [VOLt/u] to switch between "Auto / H / V ".
• Toneburst: Press [VOLt/u] to switch this function "On" or "Off".
3. DiSEqC1.0 4Port: Use [VOLt/u] to switch the options of DiSEqC1.0.
Between Disable / LNB1 / LNB2 / LNB3 /LNB4.
4. TP Index: Use [VOLt/u] to select the desired transponder or press [OK]
to open the TP list to select directly with [CHp/q], press [OK] again to
display the TP number where the channel can be found.
5. FTA Only: Press [VOLt/u] to select to scan only free channels or even
scrambled channels. If you select "Yes" it will scan free channels only.
6. Scan Channel: Press [VOLt/u] to select to scan TV + radio channels, or
just TV channels or radio channels.
CONTACT US 858.546.5050
SIRD-FTA-2
4.1
www.picomacom.com
17