Page 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.
Email: manuals@grizzly.com Machine Description Manufacture Date of Your Machine the model g0462 Wood Lathe is designed to turn wood stock so the operator can remove material with a hand-held cutting tool or chisel. the variable speed allows for infinite spindle speed adjustment from 600–2400 rpm, and the...
& spur Center Lock Lever digital tailstock readout Live tool rest handwheel Center motor head Variable Lock Lever speed Lever power tool rest Base switch head pivot w/pivot Arm Lock pin figure 1. model g0462 identification. G0462 Wood Lathe (Mfg. Since 3/10)
MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0462 WOOD LATHE WITH DIGITAL READOUT Product Dimensions: Weight................................287 lbs. Width (side-to-side) x Depth (front-to-back) x Height..............72-1/2 x 19 x 48 in.
Page 7
The information contained herein is deemed accurate as of 9/23/2013 and represents our most recent product specifications. Model G0462 PAGE 2 OF 2 Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. G0462 Wood Lathe (Mfg. Since 3/10)
Everyday ery. Never operate under the influence of drugs or eyeglasses are not approved safety glasses. alcohol, when tired, or when distracted. G0462 Wood Lathe (Mfg. Since 3/10)
Use this lathe with respect and caution to reduce the risk of operator injury. If normal safety precautions are overlooked or ignored, serious personal injury may occur. G0462 Wood Lathe (Mfg. Since 3/10)
SEcTION 2: cIRcUIT REQUIREMENTS 110v Operation power connection Device the model g0462 comes prewired with a nemA 5-15 plug, as shown in figure 2. GROUNDED 5-15 RECEPTACLE Serious personal injury could occur if you connect the machine to power before com- pleting the setup process.
Otherwise, filing a freight claim can be difficult. When you are completely satisfied with the condi- tion of your shipment, inventory the contents. -10- G0462 Wood Lathe (Mfg. Since 3/10)
SUffOcATION HAzARD! Immediately discard all plas- tic bags and packing materi- als to eliminate choking/suf- focation hazards for children and animals. figure 5. Box 2 inventory. -11- G0462 Wood Lathe (Mfg. Since 3/10)
Repeat Steps 2–3 as necessary until clean, figure 6. model h9692 industrial orange power then coat all unpainted surfaces with a quality Cleaner/degreaser (99.9% biodegradable). metal protectant to prevent rust. -12- G0462 Wood Lathe (Mfg. Since 3/10)
Shadows, glare, or strobe effects that may distract access restricted location. or impede the operator must be eliminated. Wall 30" 75" 19" Recommended 48" For Outboard Turning Illustration Not To Scale figure 7. minimum working clearances. -13- G0462 Wood Lathe (Mfg. Since 3/10)
Anchor studs are stronger and more per- manent alternatives to lag shield anchors; however, they will stick out of the floor, which may cause a tripping hazard if you decide to move your machine. -14- G0462 Wood Lathe (Mfg. Since 3/10)
Note: The headstock end is the heaviest and usually requires two people lifting at that end. figure 12. installing handle into tool rest. -15- G0462 Wood Lathe (Mfg. Since 3/10)
Flip the paddle up to turn the lathe ON. Note: Make sure that your hand stays poised over the switch in case you need to quickly turn the machine OFF. figure 14. digital readout installed. -16- G0462 Wood Lathe (Mfg. Since 3/10)
Page 19
OFF, disconnect it from power, and refer to the troubleshooting figure 15. removing switch disabling key from chart on page 31, or call our tech support the paddle switch. at (570) 546-9663 for additional help. -17- G0462 Wood Lathe (Mfg. Since 3/10)
Adjusting Head Damage to your eyes and lungs could result from using this machine without proper pro- the model g0462 headstock can be positioned tective gear. Always wear safety glasses and anywhere along the bed and pivoted up to 180˚.
20. tailstock lock lever. figure 19. head set at 90˚ and 180˚. release the pivot lock pin. make sure the pin has engaged in its detent by trying to rotate the headstock. -19- G0462 Wood Lathe (Mfg. Since 3/10)
ALWAyS make sure all of Tool Rest the tool rest locks are tight before beginning operation. the model g0462 comes with a three-way adjust- figure 22. tool rest position relative to the able tool rest (see figure 21). workpiece.
(see figure 24). Live Center Quill Lock Lever Knockout tool figure 25. installing the live center into the tailstock. figure 24. removing spur center using the knockout tool. -21- G0462 Wood Lathe (Mfg. Since 3/10)
Steps 3–4 in to retract the quill back into the tailstock until reverse. the center is forced out. For detailed instructions on mounting a workpiece to the faceplate, refer to faceplate Turning on page 26. -22- G0462 Wood Lathe (Mfg. Since 3/10)
Step 1. if your workpiece is over 2" x 2", cut the cor- ners off the workpiece length-wise to make turning the corners safer and easier. -24- G0462 Wood Lathe (Mfg. Since 3/10)
Serious personal injury could you will use. if you are unsure, read books or result if care is not taken in this procedure. magazines about lathe techniques and seek training from experienced users. -25- G0462 Wood Lathe (Mfg. Since 3/10)
Note: Allow the glue joint to completely cure according to the manufacturer's instructions. Follow the instructions above to attach the figure 36. Correct screw type for faceplate faceplate to the backing block. attachment. -26- G0462 Wood Lathe (Mfg. Since 3/10)
12''. For the size of the model g0462 after the turning operations are complete and and its minimum turning speed, we recommend a before removing the workpiece from the lathe, maximum diameter of 17'' for outboard turning.
Threaded insert required for mounting! figure 44. model h1064 6-pC Chisel set. figure 42. model g1082 4-Jaw Chuck. -28- G0462 Wood Lathe (Mfg. Since 3/10)
Page 31
48. robert sorby stebcentre. figure 46. model g9863 8-pC Chisel set. H6204—precision Drill chuck ⁄ "– ⁄ " x JT#3 G1676—Drill chuck Arbor MT#2 x JT#3 the best way to bore holes with your lathe! -29- G0462 Wood Lathe (Mfg. Since 3/10)
V-belt. • Any other unsafe condition. cleaning since all the bearings for the model g0462 are sealed and permanently lubricated, simply leave them alone unless they need to be replaced. do not lubricate them. Cleaning the model g0462 is relatively easy.
Bad surface finish. 1. Wrong spindle speed. 1. use trial-and-error to find a better spindle speed. 2. dull chisel or wrong chisel being used for 2. sharpen chisel or try a different chisel. the operation. -31- G0462 Wood Lathe (Mfg. Since 3/10)
Page 34
1. Align the quill keyway with the quill lock lever as move forward into lever. shown in figure 13, on page 16 and slightly tighten workpiece when the lever to engage the keyway. handwheel is turned. -32- G0462 Wood Lathe (Mfg. Since 3/10)
Aligning centers Replacing v-belt to ensure accurate and safe results, make sure the pulley system that allows the model g0462 to that the spindle and quill centers are aligned operate at variable speeds also keeps the V-belt before beginning operations.
Support at (570) 546-9663. The photos and diagrams included in this section are best viewed in color. You can view these pages in color at www.grizzly.com. READ ELECTRICAL SAFETY -34- G0462 Wood Lathe (Mfg. Since 3/10) ON PAGE 34!
INT RETAINING RING 52MM P0462088 STAND LEG LEFT/RIGHT PR26M INT RETAINING RING 52MM 96V2 P0462096V2 TAILSTOCK LEADSCREW V2.11.09 P6205ZZ BALL BEARING 6205ZZ PSS04M SET SCREW M6-1 X 12 PR11M EXT RETAINING RING 25MM -37- G0462 Wood Lathe (Mfg. Since 3/10)
MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REpLAcE that label before using the machine again. contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels. -38- G0462 Wood Lathe (Mfg. Since 3/10)
Do you think your machine represents a good value? _____ Yes _____No Would you recommend Grizzly Industrial to a friend? _____ Yes _____No Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than 3 times.
Page 42
FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: Name_______________________________ Street_______________________________ City______________State______Zip______ TAPE ALONG EDGES--PLEASE DO NOT STAPLE...
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.