Table of Contents
Advertisement
Quick Links
INSTALLATION & OPERATING GUIDE
To ensure you have the latest revision of the Operating Manual, or to view the Illustrated Parts
Catalog, Programming Manual, or Service Manual, please visit the Bunn-O-Matic website, at
www.bunn.com. This is absolutely FREE, and the quickest way to obtain the latest catalog and
manual updates. For Technical Service, contact Bunn-O-Matic Corporation at 1-800-286-6070.
10218.0000Z 07/13 ©1994 Bunn-O-Matic Corporation
N
IO
U T
R Y
C A
J U
IN
A L
.
O N
R D
R S
Z A
D
A N
P E
H A
R S
S
G E
C T
F IN
B JE
R
N O
P E
G .
E P
O P
K E
IG
N IN
R E
F H
P E
F O
T O
E O
O U
U T
C H
O R
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601
G9-2 HD
G9-2T HD
G9-2 HD-S
P E
O R
FAX: (217) 529-6644
N
IO
U T
R Y
C A
J U
IN
A L
.
O N
R D
R S
Z A
D
A N
H A
R S
S
C T
G E
F IN
JE
O B
P E
R
G .
E P
N
K E
IG
O P
N IN
R E
F H
P E
F O
T O
E O
O U
U T
C H
Advertisement
Table of Contents
Related Manuals for Bunn G9-2 HD
Summary of Contents for Bunn G9-2 HD
- Page 1 To ensure you have the latest revision of the Operating Manual, or to view the Illustrated Parts Catalog, Programming Manual, or Service Manual, please visit the Bunn-O-Matic website, at www.bunn.com. This is absolutely FREE, and the quickest way to obtain the latest catalog and manual updates. For Technical Service, contact Bunn-O-Matic Corporation at 1-800-286-6070.
- Page 2 AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND. In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any other special, incidental or consequential damages.
-
Page 3: Table Of Contents
HAZARDOUS READ THE ENTIRE OPERATING MANUAL INCLUDING THE LIMIT OF WARRANTY AND VOLTAGE LIABILITY BEFORE BUYING OR USING THIS PRODUCT DISCONNECT FROM POWER SOURCE 20545-0000D 01/04 © 1990 Bunn-O-Matic Corporation BEFORE REMOVING! #20545.0000 #34891.0000 PERSONAL INJURY HAZARD. KEEP FINGERS AND 00824.0002... -
Page 4: Electrical Requirements
ELECTRICAL REQUIREMENTS This grinder has an attached cordset and requires 2-wire, grounded service rated 120 volts ac, 15 amp, single phase, 60 Hz for 120V models and 230 volts ac, 10 amp single phase, 50 Hz for 230V models.. CE REQUIREMENTS •... -
Page 5: Initial Set-Up
PREVENTIVE MAINTENANCE Bunn-O-Matic Corporation recommends that preventive maintenance be performed at regular intervals. Maintenance ® should be performed by a qualified service technician. For Technical Service, contact Bunn-O-Matic Corporation at ® 1-800-286-6070. NOTE: Replacement parts or service caused by failure to perform required maintenance is not covered by warranty. -
Page 6: Coffee Grinding
COFFEE GRINDING P597 P598 P599 P600 P601 STEP 1 STEP 2 STEP 3 STEP 4 STEPS 5 & 6 1. Visually inspect the selected hopper for an ample supply of whole bean coffee. 2. Place a paper filter into the brew funnel. The filter must not be folded-over or tilted to one side. 3. -
Page 7: Adjustments
ADJUSTMENTS The grind can be set from very fine to very coarse. The amount may be adjusted for use in most commercial coffee brewers. The following procedures should be used to make adjustments. A change in the burr adjustment will also change the amount dispensed. Any adjustment of the burrs should be followed by an adjustment of the timer. - Page 8 ADJUSTMENTS (cont.) 3. Use the table on the next page to find approximate timer setting for the grind and amount of coffee de- sired. 4. Plug-in the grinder. Select either the right or left hopper with the selector switch. Do not press the start switch.