Srm350 V2 Specifications - Mackie SRM350 User Manual

SRM350 v2 SPECIFICATIONS

System Specifications
Frequency Response (–3 dB)
Frequency Range (–10 dB)
Max SPL Long-Term @ 1m
Max SPL Peak @ 1m
Crossover
Audio
Input Type
Input Impedance
Sensitivity (center detent)
Line:
Mic:
Maximum Input Level +22 dBu
Acoustic Contour Equalization (peaking)
Operating Temperature Range
Power Amplifiers
Low-Frequency Power Amplifier
Rated Power
Rated THD
Cooling
Design
High-Frequency Power Amplifier
Rated Power
Rated THD
Cooling
Design
* Rated power is continuous rms wattage into transducer's rated imped-
ance @ 1 kHz for the HF amplifier and @ 100 Hz for the LF amplifier.
Transducer Specifications
Low-Frequency Transducer
Diameter
Voice Coil Diameter
Sensitivity (1W@1m) 96 dB
Power Handling
Frequency Range
Magnet Type
High-Frequency Transducer
Diaphragm Diameter 1.4 in/36 mm
Horn Exit Diameter
Diaphragm Material Titanium
Sensitivity (1W@1m) 104 dB
Nominal Impedance
Power Handling
Frequency Range
Magnet Type
Horn Design
Horizontal Coverage
90º (1 kHz - 20 kHz)
Vertical Coverage
80º (1 kHz - 20 kHz)
Mouth Size
11.1 in x 6.1 in (283 mm x 154 mm)
83 Hz - 18.5 kHz
61 Hz - 22 kHz
118 dB
121 dB
Linkwitz-Riley
24 dB/octave @ 2400 Hz
Balanced Differential
94k ohms
+4 dBu
–36 dBu
+3 dB @ 100 Hz,
+3 dB @ 12 kHz
–10ºC - 45ºC (14ºF - 113ºF)
165 watts continuous*
< 0.03%
Convection Extrusion
Class D
30 watts continuous*
< 0.03%
Convection Extrusion
Class AB
10 in/250 mm
2.0 in/51 mm
250 watts rms, long-term
61 Hz - 3 kHz
Neodymium
1 in/25.4 mm
16 ohms
75 watts rms, long-term
1 kHz - 20 kHz
Ceramic
Enclosure Construction Features
Basic Design
Material
Finish
Handles
Grille
Line Input Power
Power Consumption
US
Recommended Amperage Service 2.5 amps
Europe
Recommended Amperage Service 1.25 amps
Japan
Recommended Amperage Service 3.0 amps
AC Connector
Note: The SRM350v2 does not support multiple voltage configurations.
Make sure the voltage rating for your particular model (as indicated
on the rear panel near the IEC socket) corresponds with your local AC
mains voltage.
Control System Functions
Electronic Crossover
Phase Alignment
Equalization
Parametric Equalization
Safety Features
Protection
Display LEDs Signal, Power, Limit
Physical Properties
Height
Width
Depth
Weight
Mounting Methods
Optional hanging brackets for top and bottom of enclosure
(SRM350 Bracket Kit: Part No. 0016404).
Never attempt to suspend the cabinet by its handles.
The SRM350 v2 is pole-mountable via the built-in socket on the bottom
of the cabinet. Be sure the pole is capable of supporting the weight of the
SRM350 v2.
Disclaimer
Since we are always striving to make our products better by incor-
porating new and improved materials, components, and manufacturing
methods, we reserve the right to change these specifications at any time
without notice.
"Mackie" and the "Running Man" figure are registered trademarks
of LOUD Technologies Inc.
All other brand names mentioned are trademarks or registered
trademarks of their respective holders, and are hereby acknowledged.
©2004-2007 LOUD Technologies Inc.
All Rights Reserved.
Asymmetrical Trapezoidal
Polypropylene
Midnight blue textured finish
One on side, one on top
Perforated metal with
weather-resistant coating
120 watts with musical program and
LIMIT LED blinking
120 VAC, 60 Hz
230 VAC, 50 Hz
100 VAC, 50/60 Hz
3-pin IEC 250 VAC
Low-frequency Dynamic Bass Protection,
Power Supply, and Amplifier Thermal Protection
20.75 in/527 mm
13.10 in/333 mm
12.25 in/311 mm
26 lb/11.8 kg
R
17