1. Manuals
  2. Brands
  3. Mackie Manuals
  4. Speakers
  5. SRM350 V2
  6. Owner's manual

Mackie SRM350v2 Owner's Manual

Hide thumbs Also See for SRM350v2:
Table of Contents

Advertisement

Quick Links

See also: User Manual
SRM350v2
Powered Loudspeaker
O W N E R ' S M A N U A L

Advertisement

Table of Contents
loading

Related Manuals for Mackie SRM350v2

Summary of Contents for Mackie SRM350v2

  • Page 1 SRM350v2 Powered Loudspeaker O W N E R ’ S M A N U A L...

  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 19. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC 2. Keep these instructions. Rules. These limits are designed to provide reasonable protection 3.

  • Page 3: Table Of Contents

    8. LIMIT Indicator .............9 9. INPUT Connector ............9 10. THRU Connector ............9 • Please write the serial number for your SRM350v2 here (or for both SRM350v2s if you have two) for future reference (insurance claims, tech support, return authorization, etc.):...

  • Page 4: Introduction

    This results in improved efficiency for the original. SRM means Sound Reinforcement Monitor, the low-frequency amplifier because it is not wasting and the SRM350v2 truly produces a studio quality sound in power trying to reproduce frequencies we hear a sound reinforcement speaker.
  • Page 5 The Active Advantage • The connecting wires between the amplifier outputs There are a number of advantages to using an active and the drivers are kept to a minimum, so the damping speaker system over a passive loudspeaker: factor of the amplifier isn’t compromised by the resistance of long speaker cables.

  • Page 6: Hookup Diagrams

    3. Connect the supplied AC power cord to the IEC socket 1. Start with the following settings on the back of the on the back of the SRM350v2. Plug the other end into an SRM350v2: AC outlet properly configured with the correct voltage Turn the POWER switch off (down).
  • Page 7 SPM200 Speaker Pole Mount, saving the cost of a more Power Power Cords Cords expensive tripod stand. SRM1801 SRM1801 plays the low plays the low frequencies frequencies Mixing Console (Mackie Onyx 1220i shown) SRM350v2: 3-WAY SYSTEM WITH A POWERED SUBWOOFER...

  • Page 8: Rear Panel Description

    2. POWER Switch The SRM350v2 has several connectors, controls, and indicators that you should understand. Switch up to turn the SRM350v2 on. Make sure the 1. IEC Socket LEVEL control is down before you turn it on. Press the bottom of this switch to put the speaker into standby mode.

  • Page 9: Contour

    LEVEL control. If you have a microphone NORMAL position (12 o’clock). If you have a particularly connected to the first SRM350v2 and you have the high line-level signal connected to the SRM350v2, you may MIC/LINE switch pushed in, the signal at the THRU jack need to turn the control down to the 9 o’clock position.

  • Page 10: Connections

    PLACEMENT The SRM350v2 has a combination female XLR and 1/4" The SRM350v2 active speakers are designed to sit on the TRS input that accepts a balanced or unbalanced mic- or floor, a tabletop, or to fit on a standard tripod speaker stand.

  • Page 11: Rigging

    Here are some useful placement tips: • Avoid placing loudspeakers in the corners of a room. The SRM350v2 cabinets are fitted with four M5 insert This increases the low-frequency output and can cause points on the top and bottom for installing an optional the sound to be muddy and indistinct.

  • Page 12: Thermal Considerations

    CONSIDERATIONS CONSIDERATIONS The amplifiers inside the SRM350v2 are Be sure the SRM350v2 is plugged into an outlet that is convection cooled by a large heatsink. able to supply the correct voltage specified for your model. For efficient cooling, it is important to...
  • Page 13 15A service. about. You may even be faced with This allows each SRM350v2 to be safely operated at 2-wire outlets that are missing the its maximum level. third safety ground pin. It’s a good idea...

  • Page 14: Service Information

    You may have your positive and negative connections reversed at one • Our favorite question: Is it plugged in? Make sure the end of one cable, causing one SRM350v2 to be AC outlet is live (check with a tester or lamp). out-of-phase.
  • Page 15 • Is there a light dimmer or other SCR-based device on dealers, or you can make your own from two TV baluns the same AC circuit as the SRM350v2? Use an AC line (standard TV 75/300 ohm adaptors): filter or plug the SRM350v2 into a different AC circuit.

  • Page 16: Repair

    “Support” and select “Locate a Service Center.” Service for Mackie products living outside the United States can be obtained through local dealers or distributors. If you do not have access to our website, you can call...

  • Page 17: Specifications

    2.0 in / 51 mm Never attempt to suspend the cabinet by its handles. Sensitivity (1W@1m) 96 dB The SRM350v2 is pole-mountable via the built-in socket on the bottom of Power Handling 250 watts rms, long-term the cabinet. Be sure the pole is capable of supporting the weight of the...

  • Page 18: Block Diagram

    SRM350v2 BLOCK DIAGRAM...

  • Page 19: Limited Warranty

    The Product Warranty will not extend to anyone other than the original purchaser of the product (hereinafter, “Customer,” “you” or “your”). For products purchased outside the U.S. or Canada, please visit www.mackie.com/warranty to find contact information for your local distributor, and information on any warranty coverage provided by the distributor in your local market.
  • Page 20 16220 Wood-Red Road NE • Woodinville, WA 98072 • USA United States and Canada: 800.898.3211 Europe, Asia, Central and South America: 425.487.4333 Middle East and Africa: 31.20.654.4000 Fax: 425.487.4337 • www.mackie.com E-mail: sales@mackie.com...

Table of Contents