A3 Digital Out; A4 Remote; A5 2Way Remote; A6 Dimmer - Denon AVP-A1HDE Owner's Manual

A3 Digital Out
Set usage of OPT4 OUT.
[Selectable items] ZONE4 Select Rec Select
NOTE
The ZONE4 operations cannot be performed when set to "Rec
Select" .
A4 Remote ID
Set remote control ID.
Match the ID setting of the remote control unit and the receiver.
[Selectable items] 1 2 3
• When changing the remote ID, also change the AMP , iPod and
NET/DTU modes of the main remote control unit at the same time
(vpage 72).
• When changing the remote ID, also change the sub remote control
unit at the same time (vpage 77).
A5 2Way Remote
Set when using the 2-way remote control unit.
[Selectable items] Used Not Used
When using a 2-way remote control unit (RC-7000CI and RC-7001RCI,
sold separately), set this to "Used" .
NOTE
• When using the 2-way remote control unit, connect to the Port 1 RS-
232C connector.
• If GUI menu "Manual Setup" – "Option Setup" – "2Way Remote"is
set to "Used" , you cannot use port 1 of the RS-232C terminal for the
external controller.

A6 Dimmer
Adjust display brightness of the receiver.
[Selectable items] Bright
Operating from the main unit
Press the DIMMER button.
If POA-A1HD is connected using the control link, POA-A1HD meter
operation is turned OFF when the AVP-A1HD display is turned "OFF" .
4
A7 Setup Lock
Protect settings from inadvertent change.
[Selectable items]
• When "Setup Lock" is set to "ON" , the settings listed below can
no longer be changed. Also, "SETUP LOCKED!" is displayed if you
attempt to operate related buttons.
⋅ GUI menu operations
⋅ RESTORER
⋅ Night Mode
⋅ Parameter
⋅ Room EQ
⋅ Channel Level
⋅ Audio Delay
• To cancel the setting, press the
Lock" screen, then change the setting to "OFF" .
A8 Maintenance Mode
This sets the function for maintenance by a DENON serviceperson
or installer. (For professional use only.)
This function allows a DENON serviceperson or installer to check the
AVP-A1HD's status and make settings via the Internet.
NOTE
Only use this function if so instructed by a DENON serviceperson or
installer.
Dim Dark OFF
Bright Dim
OFF Dark
ON OFF
MENU
button to re-display the "Setup
A9 Firmware Update
Update the firmware of the receiver.
If POA-A1HD is connected using the control link, POA-A1HD is updated
simultaneously with update of AVP-A1HD.
Check for Update
You can check for firmware updates. You can also check approximately
how long it will take to complete an update.
Start
Execute the update process.
When updating starts, the power indicator becomes red and the GUI
screen is shut down.
The amount of update time which has elapsed is displayed during the
update process.
When updating is complete the power indicator becomes green and
normal status is resumed.
b If the display reads as shown below, check the settings and network
environment, then update again.
Display Description
Updating failed Updating failed.
Login failed Failure to log into server.
Server is busy Server is busy. Wait a while then try again.
Connection fail Failure connecting to server.
S0 Add New Feature
Display the new functions which can be purchased for downloading
to the AVP-A1HD and upgrade.
When you purchase a new function and register your user information,
"Registerd" is displayed on this menu and you can proceed with the
upgrade.
Upon completion of the upgrade, you can start using the new
function.
When "Not Registered" is displayed on the Add New Feature screen,
you cannot upgrade.
To use the upgrade function, you should purchase an upgrade package
from the DENON website.
To purchase the package, you will need the ID number shown on this
screen.
To display the ID number on the screen, hold the
buttons down for 3 seconds or more.
<p> <STATUS>
and