Table of Contents
Advertisement
Quick Links
H
olliston
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and
proper installation; therefore, before attempting to install and operate your Casablanca fan, read this owner's
manual completely and carefully. Retain this manual for future reference.
Caution: to avoid possible electrical shock, make certain that electricity is turned off at the circuit breaker
or fuse box before attempting any installation procedure.
IntroductIon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Before .You .Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Safe .use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
MountInG .rEcoMMEndAtIonS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
General .Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
sloped .ceiling .installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
FAn .InStAllAtIon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Getting .Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
ceiling .plate .Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
lag .Screw .Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
canopy .Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Fan .Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Hanging .the .Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
canopy .Electrical .connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
canopy .Hatch .and .cover .ring .Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Blade .Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
lIGHt .FIXturE .Installation .(optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
control .InStAllAtIon .And .oPErAtIon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
switch .housing .and .end .cap .Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
control .Battery .Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
changing .frequency .setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
operation .cFl .Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
control .Holster .Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
operation .Speed .control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
operation .reversing .Airflow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
operation .lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
trouBlESHootInG . t IPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
cArE .rEcoMMEndAtIonS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Product .SPEcIFIcAtIonS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
DC
™
Read and Save theSe inStRuCtionS!
ContentS
Pn C31B43001 hn0411
H
olliston
owner's Manual
DC
™
1
Advertisement
Table of Contents
Related Manuals for Casablanca C31uxxB
Summary of Contents for Casablanca C31uxxB
-
Page 1: Table Of Contents
Read and Save theSe inStRuCtionS! Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the product and proper installation; therefore, before attempting to install and operate your Casablanca fan, read this owner’s manual completely and carefully. Retain this manual for future reference. - Page 2 PLEASE INSPECT ALL PACKAGING PRIOR TO DISCARDING! Your .casablanca .fan .was .crafted .with .pride .and .care .and .inspected .thoroughly .prior .to .shipment . . Before . you .begin .to .assemble .and .install .your .casablanca .fan, .remove .all .parts .from .the .carton .and .check .them .
-
Page 3: Parts Guide
™ olliston Parts Guide Item # Description Picture (not to scale) Quantity Motor Housing Ceiling plate Phillips Screwdriver Screw Pack (A): 2 EA 1" x 8-32" Roundhead screws and Washers Screw Pack: 1 EA Lag Screw and Washer (1) Screw Pack (A): Wire Nuts (4), Canopy and Canopy Hatch Perma•Lock™... - Page 4 Item # Description Picture (not to scale) Quantity Blades Blade Irons Screw Pack (C): Blade iron Screws (pre-installed, see pg 13, step 9a) Screw Pack (D): 16 EA Blade Screws and Washers Light Kit Adaptor Assembly Screw Plug Switch Housing Cap Screw Pack (E): Switch Housing Cap Screws 8-32 x 3/8 DC Remote Control...
-
Page 5: Introduction
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan installations. If it is not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling installations. -
Page 6: Mounting Recommendations
MoUntInG recoMMendatIonS General GUIdelIneS Before mounting your Casablanca fan, read the following helpful recommendations. The location of the fan, air circulation, and fan size are all important factors to consider before installation. Location Ceiling fans have practical uses in almost every room in your home. We suggest you follow these mounting recommendations as you decide where to install your Casablanca fan. -
Page 7: Fan Installation
If you do not have an existing fixture located where circuit breaker or fuse box), lower the old fixture and you wish to place your Casablanca fan, an approved disconnect the wiring. Check the ceiling fixture outlet ceiling fixture outlet box must be installed and wired. -
Page 8: Lag Screw Installation
Step 3. Attach the canopy to the ceiling plate with three of the 8-32 x 2 " long canopy screws and lock washers provided with your Casablanca fan. Tighten using the provided screwdriver until snug against the ceiling. NOTE: On sloped ceilings, align the canopy opening with the top or peak of the room. -
Page 9: Fan Preparation
™ olliston fan preparatIon PeRMa•LoCk™ haRdWaRe (not to scale) Canopy Cover Ring Perma•Lock™ downrod allen Wrench hanging adapter Cover and Ball assembly iMPoRtant SaFetY inFoRMation: PaPeR MotoR Before starting the installation of your ShieLd ceiling fan, install the threaded downrod into the motor coupling and lock the assembly. - Page 10 fan preparatIon - contInUed MOTOR WIRES (LEAVE AT LEAST Step 4c. Slide both the hanging adapter cover and 6" LONG) canopy cover ring on to the pole, then route the CANOPY COVER wires through the 3.5" Perma•Lock downrod and ball RING PERMA•LOCK™...
-
Page 11: Hanging The Fan
™ olliston fan preparatIon - contInUed Step 4e. Slide the hanging adapter cover down over the motor coupling as shown in Figure #6, making sure that the adapter cover is covering the motor coupling as in shown Figure #7. HANGING HANGING ADAPTER ADAPTER COVER... -
Page 12: Canopy Electrical Connections
canopY electrIcal connectIonS Step 7. Attach the fan wires to the ceiling fixture outlet box wiring by placing the bare ends of the wires side by side and then securing with a wire nut. Test that the connection is secure by pulling on the wire nut. Connect in this order: WIRE NUT •... -
Page 13: Blade .Installation
™ olliston Blade InStallatIon Blade Hardware (not to scale) Blade iron Phillips Blade irons (5) Blade Screws (16) Blades (5) Washers (16) Screws Screwdriver Step 9a. Remove the five shipping blocks, and screws as shown in Figure #2. DO NOT discard the ten (10) screws;... -
Page 14: Light Fixture Installation (Optional)
Blade installation Continued Step 10b. Attach a blade/blade iron assembly to the motor by using two blade iron screws provided. Place the end of the blade iron on the motor as shown in Figure #5. Insert the screws one by one using the MotoR provided screwdriver. -
Page 15: Switch .Housing .And .End .Cap .Installation
™ olliston SwItcH HoUSInG and end cap InStallatIon no LiGht kit - Installation: SCReW SCReW PLuG #6-32 NOTE: If you are installing your fan without a light kit attached as shown in Figure #1, continue with these BottoM CaP installation instruction SCReW #6-32 Figure #1... - Page 16 Switch housing and Light kit CenteR ShaFt adaptor installation: - adaPteR ( no LiGht kit) Step 12a. Locate and remove the three #8-32 screws from the center shaft adapter located on adaPteR SCReWS the bottom of the fan as shown in Figure #1. Do not , #8-32 discard the screws, all three screws will be needed for the next steps with in this document.
- Page 17 ™ olliston Switch housing and Light kit adaptor installation - Continued ( no LiGht kit) Step 12e. Locate the bottom cap and screw as shown in Figure #5, using the screw that you earlier removed from the light kit adaptor assembly (see step 11c) and insert cap screw through the hole in the center of the cap and attaching the cap the bottom of the fan as shown in Figure #5 on this page.
- Page 18 SwItcH HoUSInG and end cap InStallatIon LiGht kit SCReW - Installation: #6-32 SCReW PLuG NOTE: If you are installing your fan with a light kit attached as below in Figure #1, continue with these installation instruction Step 13a. Also you will need the BottoM CaP SCReW installation instructions that came with your new light...
- Page 19 ™ olliston Switch housing and Light kit CenteR ShaFt adaptor installation: - Continued adaPteR ( LiGht kit) Step 14a. Locate and remove the three (3) #8-32 screws from the center shaft adapter located on the adaPteR SCReWS, bottom of the fan as shown in Figure #6. #8-32 (Screws 3) Figure #6...
- Page 20 Switch housing and Light kit adaptor installation: - Continued ( LiGht kit) White Step 14e. Align the four screw holes on the cap with WiRe the holes on the light kit adaptor plate, using the four (4) screws that you earlier removed from the light kit adaptor assembly (see step 11c) and insert the four (4) screws, attaching the cap to the bottom of the fan as shown in Figure #10 on this page.
- Page 21 ™ olliston Switch housing and Light kit adaptor installation: - Continued ( LiGht kit) Step 14g. Connect the wires of the motor to the wires of the light fixture. Connect the BLue wire from the motor to the BLaCk wire of the light fixture and connect the two White wires together, as shown in Figure #15.
-
Page 22: Control Installation And Operation
dC Control Control InstallatIon and operatIon Control Battery InstallatIon Step 1. Open battery compartment door by pressing down and sliding battery door down. Step 2. Install 1 "A23" "MN21" alkaline battery in the space provided. Please observe proper polarity placement. CHangIng frequenCy settIng you will have to change the dip switch settings in the remote if you are using more than one fan in the same area and want to control... -
Page 23: Control Holster Installation
dC Control Control Holster InstallatIon Step 1. Locate a 2x4 wall stud in a convenient location. Step 1. Orient the control bracket as shown over the 2x4 stud. Step 1. Use the provided screws in the mounting holes. Install and tighten screws by hand only. operatIon speed Control There are six individual speed settings for the fan. -
Page 24: Operation Lights
dC Control operatIon lIgHts To turn the lights off and on, press and release the button for less than one second. To dim the light, Press and hold the button for more than 1 second. The light will come on at the last brightness setting and increase in brightness until full power is reached, then start dimming until the lowest setting is reached. -
Page 25: Troubleshooting Tips
Consult the dealer or an experienced radio/TV technician for help. Note: Any changes or modifica- tions to the transmitter or receiver not expressly approved by Casablanca Fan Company may void one’s authority to operate this remote control. -
Page 26: Care Recommendations
Lubrication • Never lubricate this fan! The precision motor at the heart of your Casablanca fan features sealed bearings that are lubricated for life. • Do not attempt to oil the motor.