Advertisement

User Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TriShot LED and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Chauvet TriShot LED

  • Page 1 User Manual...
  • Page 2: Table Of Contents

    Document Information The information and specifications contained in this document are subject to change without notice. CHAUVET® assumes no responsibility or liability for any errors or omissions that may appear in this manual. © Copyright 2011 CHAUVET®. All rights reserved Printed in P.R.C.
  • Page 3: Before You Begin

    1. B EFORE YOU EGIN What is Included  1 x TriShot™ LED  1 x Warranty Card  1 x User Manual Unpacking Instructions Immediately upon receiving this product, carefully unpack it and check the container in which you received it. Make sure that you have received all the parts indicated above and that they are all in good condition.
  • Page 4: Safety Notes

    Safety Notes Please read the following notes carefully because they include important safety information about the installation, usage, and maintenance of this product.  Keep this User Manual for future consultation. If you sell this product to another user, be sure that they also receive this document. ...
  • Page 5: Introduction

    2. I NTRODUCTION Product Overview Focus adjustment DMX out DIP switches Microphone Sensitivity Bracket adjustment knob Fuseholder Safety Power in DMX in (hardwired) TriShot™ LED User Manual (Rev. 01a) Page 5 of 18...
  • Page 6: Product Dimensions

    Product Dimensions Page 6 of 18 TriShot™ LED User Manual (Rev. 01a)
  • Page 7: Setup

    3. S ETUP AC Power This product has an auto-ranging power supply and it can work with an input voltage range of 100~240 VAC, 50/60 Hz. To determine the power requirements for a particular fixture, see the label affixed to the back plate of the fixture or refer to the fixture’s specifications chart.
  • Page 8: Mounting

    Mounting Orientation The TriShot™ LED may be mounted in any position, provided there is adequate room for ventilation around it. Rigging Be sure that the structure onto which you are mounting this product can support its weight. Please see the “Technical Specifications” section of this manual for weight information.
  • Page 9: Operation

    4. O PERATION Configuration (DMX) Set this product in DMX mode to control it with a DMX controller. 1) Connect this product to a suitable power outlet. 2) Turn this product on. 3) Connect a DMX cable from the DMX output of the DMX controller to the DMX input socket of this product.
  • Page 10: Static Colors

    Static Colors To enable the Static Colors mode, do the following: 1) Set DIP switch [8, 9, 10] to the ON position. 2) Use DIP switch [1~6] to set the color. See the chart below to see what color each DIP switch controls.
  • Page 11: Dmx Channel Assignments And Values

    DMX Channel Assignments and Values 7-CH Channel Function Value Setting 000  255 Dimmer (0~100%) 000  255 Green Dimmer (0~100%) 000  255 Blue Dimmer (0~100%) 000  009 No function Color Macros 010  255 Strobe (slow~fast) Speed 000 ...
  • Page 12: Technical Information

    5. T ECHNICAL NFORMATION General Maintenance Dust build up reduces light output performance and can cause overheating. This can lead to reduction of the light source’s life. To maintain optimum performance and minimize wear, you should clean your lighting fixtures at least twice a month. However, be aware that usage and environmental conditions could be contributing factors to increase the cleaning frequency.
  • Page 13: General Troubleshooting

    DMX amplifier after unit #32   Terminator not connected Install a terminator, as indicated in the “DMX Primer” section. If you still experience problems after trying the above solutions, contact CHAUVET® Technical Support. TriShot™ LED User Manual (Rev. 01a) Page 13 of 18...
  • Page 14: Returns Procedure

    The user must clearly label the package with a Return Merchandise Authorization Number (RMA #). CHAUVET® will refuse any product returned without an RMA #. DO NOT write the RMA # directly on the box. Instead, write it on a properly affixed label.
  • Page 15: Dmx Primer

    DMX Primer The USITT DMX512-A data transmission protocol (DMX, from now on) is based on the EIA-485 standard and it has 512 channels (001 to 512). This system requires a controller (DMX controller), one or more DMX compatible fixtures, and a DMX circuit (also known as “DMX universe”) to link the fixtures to the controller.
  • Page 16: Dmx Cabling

    You can purchase CHAUVET® certified DMX cables directly from a dealer/distributor or make your own DMX cable. If you choose to make your own DMX cable, you must use a data-grade cable such...
  • Page 17: Dip Switch Reference Guide

    DIP Switch Reference Guide You can use the table below to set your fixture’s DIP switches. Imagine that you want to find the DIP switch settings for DMX address 328: 1) Find 328 among the addresses from the table and point at it with your finger. 2) Move your finger to the left and you will find the settings for DIP Switches 1 to 5.
  • Page 18: Technical Specifications

    6. T ECHNICAL PECIFICATIONS Dimensions and Weight Length Width Height Weight 8.6 in (218 mm) 5.2 in (131 mm) 6.7 in (171 mm) 2.6 lbs (1.2 kg) Note: Dimensions in inches rounded to the nearest decimal digit. Power Power Supply Type Range Voltage Selection Switching (internal)

Table of Contents