Extra Rinse Button; Display Window; Delay Start Button - Electrolux EWT 1058 Instruction Manual

No spin
If you select the " " position, the appliance drains the
water only. This function cannot be selected with the
Whites and Coloureds programmes. This function is
very useful for very delicate laundry.
4. Water in the tub button
This button can be used with all wash and rinse pro-
grammes. The water from the final rinse is not drained
at the end of the selected programme to prevent creas-
ing the laundry if it is not removed immediately from the
drum. You can select this option at any point up to the
rinse cycles by selecting the Start/Pause button before-
hand. The Start/Pause light flashes and the remaining
time display window shows "
There are three different ways of draining the water:
• Select the Drain programme
The appliance drains the water without spinning. Before
selecting the Drain programme
lector must be in the stop position "On/Off".
• Press the Start/Pause button
The appliance drains the water and spins the washing
depending on the type of laundry at maximum speed.
• Select the spin speed
Select the desired spin speed by pressing the Spin
button and then press the Start/Pause button.
Warning: if the water is not drained within 18 hours, the
water is automatically drained.
5. Quick button
By pressing this button, the washing time is reduced as
follows:
- 49 minutes for the 90°C whites programmes,
- 62 minutes for the 60°C coloureds programmes,
- 28 minutes for synthetics,
- 8 minutes for delicates.
This function cannot be used on the wool, handwash
programmes and is recommended for lightly soiled
clothes.

6. Extra rinse button

This button can be selected with all programmes except
with wool and handwash " " programmes.
The appliance performs 4 rinses instead of 3.

7. Delay start button

This button is used to delay the start of a programme
from 1 to 24 hours.
Using delay start
• Select the programme.
• Select the required time for the delay start.
• Press the Start/Pause button.
The timer is displayed in hours.
The lid can be opened to load the washing during the
delay start period by pressing the Start/Pause button.
The programme starts when the time has elapsed.
0
".
,
the programme se-
Modifying the delay start
• Press the Start/Pause button.
• Press the Delay start button until the new number of
hours at the end of which you want the programme to
start appears in the display window; if you want to
cancel delay start, move the programme selector to
the stop position "On/Off".
• Press the Start/Pause button again so as to
activate the new delay start selection or to start
the programme (if the delay start has been
cancelled).
Be careful : if you use liquid detergent for a washing
cycle with a delay start, use a ball to put directly in the
drum and choose a programme without prewash.
If you want to realize a prewash with a delay start in the
same time, please use powder detergent.

8. Display window

This display window is used to view the following
information:
Programme cancellation - programme duration - de-
lay start - incorrect selection - error codes.
Programme cancellation
If you want to cancel a programme, turn the programme
selector dial to the stop position "On/Off". A new
programme can then be selected after cancelling the
previous one.
Programme duration
2.05 2.05
The programme duration can vary depending on the
temperature and the water inlet pressure as well as the
mains voltage of your appliance or else if foam during
rinses or imbalances during spinning are detected.
When the programme has finished, "
display window.
You can activate the delay start using the Delay start
button (24 hours maximum). The number of hours at the
end of which you want the programme to start de-
creases hour by hour.
8
This is calculated as a func-
tion of the maximum load
specified for each textile
type. The readout of the
washing time appears in
hours and minutes in the
display window and reduces
minute by minute.
0
" flashes in the
Delay start