Table of Contents
Advertisement
ENGLISH
GAudioH
Symptom
No sound is produced
•
When playing monaural audio sources, select a surround mode
from center speaker.
other than "STANDARD" (Dolby/DTS Surround).
No sound is produced
•
Set the surround mode to a mode for surround playback.
from surround
speakers.
No sound is produced
•
Check that the surround back speaker's power amplifier
from surround back
assignment is set to "Normal".
speaker.
•
Set the surround back speakers to something other than
"None".
•
Set "Surround Parameter" – "Surround Back" to something
other than "OFF".
•
Set the surround mode to the surround playback mode.
No sound is produced
•
Turn on the subwoofer's power.
from subwoofer.
•
Set the subwoofer to "Yes".
•
Check the subwoofer connections.
•
Increase the subwoofer's channel level.
DTS sound is not
•
Set the Blu-ray disc/DVD player's audio output setting to "Bit-
output.
stream". For details, refer to the Blu-ray disc/DVD player's
operating instructions.
•
Use a DTS-compatible Blu-ray disc player/DVD player.
•
Set the decode mode to "Auto" or "DTS".
Dolby TrueHD, DTS-
•
Make HDMI connections.
HD, Dolby Digital Plus
•
Set the Blu-ray disc/DVD player's audio output setting to "Bit-
audio is not output.
stream". For details, refer to the Blu-ray disc/DVD player's
operating instructions.
•
Use a DTS-compatible Blu-ray disc player.
GControl dock for iPodH
Symptom
iPod
cannot
be
•
Connect to the terminal to which "iPod dock" was assigned and
played.
switch the input source.
•
Check the iPod connections.
•
Plug the control dock for iPod's AC adapter into a power outlet.
Communications with the AVR-3310 are not possible unless the
AC adapter is plugged in.
Cause / Countermeasure
Cause / Countermeasure
GVideoH
Symptom
Page
No picture appears.
•
Check the connections of the AVR-3310's video output terminals
64
and the TV's input terminals.
•
Make the proper input setting for the input terminals of the TV
64, 65
connected to the AVR-3310.
•
Cancel the PURE DIRECT mode.
•
High definition (1080i/720p) and progressive (480p/576p) video
33
signals are not down-converted. Set the player to interlace
(480i/576i) signals.
33
•
Check the "Video Select" setting.
Picture
cannot
be
•
The REC OUT video terminal does not have a video conversion
68
recorded.
function, so use a video cable to input video signals, an S-Video
cable to input S-Video signals.
64, 65
DVDs
cannot
be
•
This is not a malfunction. Most movie software includes copy
–
copied on a VCR.
prevention signals and cannot be copied.
33
GUI is not displayed.
•
Set "Format" according to the format (NTSC or PAL) of the TV
13
being used.
34
–
GHDMIH
Symptom
–
HDMI audio signals
•
Set "Audio Out" to "AMP" to output HDMI audio signals from
48
are not output from
the speakers.
speakers.
14
–
No picture appears
•
Check the connection of the HDMI connectors.
with HDMI
•
Select the input source assigned to the HDMI terminal at "Input
connections.
Assign".
–
•
Connect a monitor that is compatible with copyright protection
(HDCP).
•
Check that the output format (HDMI FORMAT) of the connected
player, etc., matches the TV's compatible input formats.
No sound is output
•
Set "Audio Out" to "TV" to output HDMI audio signals from the
Page
from the monitor
TV.
26, 46
connected with HDMI
connections.
16
When performing the
•
Set "HDMI Control" to "OFF". When you only want to operate the
–
following operations
power on/off each device, set "Power Off Control" to "OFF".
on a connected
device, AVR-3310 has
the same operations.
•
Power ON/OFF
•
Switching
audio
output devices
•
Adjust volume
•
Switch input source
Cause / Countermeasure
Cause / Countermeasure
Page
14, 15
–
66
–
46
17
–
41
Page
35
14
26, 45
14
14, 15
35
35
Hide quick links:
Advertisement
Table of Contents
