Download Print this page

Nokia 9800 S Owner's Manual

Hide thumbs


Owner's Manual
9800 S


   Related Manuals for Nokia 9800 S

   Summary of Contents for Nokia 9800 S

  • Page 1

    Owner’s Manual MEDIAMASTER 9800 S...

  • Page 2

    Hereby, Nokia declares that this digital receiver, Mediamaster 9800 S, is in conformity with essential requirements and other relevant provisions of Directive 1999/5/EC. This Terminal Equipment is intended for connection to the analogue Public Switched Telephone Networks (PSTNs), in which network addressing, if provided, is by means of Dual Tone Multiple Frequency (DTMF) signalling.

  • Page 3: Table Of Contents

    Corporation. Other product and company names mentioned herein may be trademarks or trade names of their owners. Nokia operates a policy of continuous development. Therefore we reserve the right to make changes and improvements to any of the products described in this manual without any prior notice.

  • Page 4: General Information

    • Do not cover the Mediamaster or place it on a or humid conditions. unit that emits heat. • Service should be carried out only at a Nokia • Use a soft cloth and a mild solution of washing- Authorised Service Centre.

  • Page 5: Remote Control

    REMOTE CONTROL This section describes how to operate the Mediamaster using the buttons on the remote control. Some of the functions can also be carried out using the buttons on the front panel. Switch the Mediamaster in and out of standby mode. EXIT TV Return to the viewing mode from a menu without storing settings (in menu mode).

  • Page 6: Front And Rear Panel

    FRONT AND REAR PANEL Front Panel Button Display Push the button to release Shows channel number, error an inserted CA module messages and remote control commands. In standby mode the time is shown. Slot Slot to put the Mediamaster to move up/down in for a Smartcard for a CA module in and out of standby...

  • Page 7: Viaccess Smartcard

    ABOUT THE SMARTCARD AND CA MODULE To be able to receive scrambled digital satellite channels you will need a Smartcard and/or a Common Interface CA (Conditional Ac- cess) module * from the Service Provider of your choice. The Service Provider is the programme distributor. If you are subscribing to services from more than one Service Provider, you might have to change between different Smart- cards and/or CA modules.

  • Page 8: Preparing The Remote Control

    INSTALLATION OF THE MEDIAMASTER The box for your Mediamaster should contain the following items: • the Mediamaster • a remote control with 2 AAA batteries • a SCART lead (fully featured 1,0 metre) • an aerial/RF lead (double screened 1,5 metres) SCART lead RF lead •...

  • Page 9: Connecting The Mediamaster

    INSTALLATION OF THE MEDIAMASTER Connecting the Mediamaster There are many different types of TV/VCR and other equipment that you can connect to the Mediamaster. In this manual you will see some of the most common ways to connect your equipment. If you use RF leads you will have to tune your TV and VCR to the Mediamaster output channel (see page 11).

  • Page 10: Connecting An Analogue Satellite Receiver And A Vcr

    A B in the diagram) or a Universal Twin LNB. Analogue receiver Nokia Smart switch • Connect a coaxial cable between output A on the NOKIA Smart switch (accessory) to the LNB socket on the analogue receiver. • Connect a coaxial cable between output B on the NOKIA Smart switch to the ANTENNA socket on the Mediamaster.

  • Page 11: Switching On For The First Time With Scart Connections

    INSTALLATION OF THE MEDIAMASTER Switching on for the First Time with SCART Connections • Plug in your Mediamaster • Now you will see the ”Welcome” menu on the screen. • Press OK on the Mediamaster remote control to start the In- stallation procedure.

  • Page 12: First Time Installation

    FIRST TIME INSTALLATION General Information Once you have correctly connected the Mediamaster, you also have to perform a “First Time Installation.” During this procedure, helpful information is displayed at the bot- tom of the menus. Please note! The OK button always confirms a selection within these menus, and pressing it will take you to the next step in the installation process.

  • Page 13: Rf Modulator Type

    FIRST TIME INSTALLATION RF Modulator Type If the Mediamaster is connected to the TV with a RF cable, you must select the right RF modulator alternative, which is depend- ent on the country where the Mediamaster is being used. Select “Normal (PAL B/G)” when the box is used outside the Select “UK (PAL I)”...

  • Page 14: Antenna Adjustment And Signal Check

    FIRST TIME INSTALLATION Antenna Adjustment and Signal Check Pressing OK from the selected alternative in the previous menu will display the Antenna Adjustment menu (shown to the right) on the screen. For each satellite, (e.g. ASTRA, HOTBIRD, SIRIUS, THOR), up to 4 different channels are preprogrammed and shown in the menu.

  • Page 15

    FIRST TIME INSTALLATION Line through on the Antenna Sat- ellite Selection Menu Select one of the alternatives ASTRA, HOTBIRD, SIRIUS or THOR when you have a single LNB pointed towards any of these satellites. Then follow the “Antenna Adjustment and Signal Check” in- structions on the previous page.

  • Page 16: Antenna/satellite Selection

    FIRST TIME INSTALLATION Line 7 on the Antenna Satellite Selection Menu This selection is necessary only if your satellite choice differs from the preprogrammed satellite alternatives (line 1-4) in the fol- lowing ways; if you do not use a universal LNB or when you have more than two LNB’s.

  • Page 17: Multisatellite/diseqc Switch Configuration

    FIRST TIME INSTALLATION Multisatellite/DiSEqC switch configuration Select this alternative if your antenna system has more than one LNB and when you not use any of the alternatives Astra/Hotbird or Thor/Sirius from the menu “Antenna/satellite selection” on page 13. You can connect up to 4 LNBs. The selection of the different LNBs must be controlled by an external switch.

  • Page 18: Antenna Motor Installation

    13) and press OK. • Select line 3, “Motor Antenna Configuration” and press OK. Type of motor • Select SATSCAN if it is a Nokia SatScan motor. • Select DiSEqC in case the motor you use is controlled by DiSEqC commands.

  • Page 19

    FIRST TIME INSTALLATION Adjust Motor for ASTRA To continue the installation you now have to determine the angle to ASTRA 1. The motor and the antenna must be adjusted towards the ASTRA 1 satellites on 19,2 East as this is the reference setting. All other prepro- grammed satellite positions are oriented relative to ASTRA 1.

  • Page 20

    FIRST TIME INSTALLATION ..and you will get the Channel Search menu. The most common is to start from the “Automatic Search” line. (You can always make a Manual or Advanced Search later on.) • Select ASTRA on the Automatic Search line •...

  • Page 21

    FIRST TIME INSTALLATION When the channel search from ASTRA is finished you can search for channels from other satellites. • Press MENU on the remote control and the MAIN MENU will appear on the screen. • Select line 6, System Configuration •...

  • Page 22: Channel Search Progress

    FIRST TIME INSTALLATION East and West Limit Set Up You only have to set these limits if the antenna is prevented from reaching its East/West limit positions. This could be the case e.g. if the antenna is mounted too tight to a wall or in any similar situ- ation.

  • Page 23: Viewing Mode

    VIEWING MODE General Information The following describes the basic functions of your Mediamaster while watching satellite TV or listening to satellite radio. Some of the functions described here are dependent on the Service Provider and can only be used if they are included in the transmitted programme information.

  • Page 24: The "i" (information) Button

    VIEWING MODE The “i” (Information) Button The Mediamaster has the ability to display information about pro- grammes currently being broadcast as well as those being broad- cast next. This procedure is the same for both TV and Radio mode. By pressing the “i” button while watching TV you will get a spe- cial Programme Information Banner.

  • Page 25: List Of Tv And Radio Channels

    VIEWING MODE List of TV and radio channels At the channel search procedure, two channel lists are created. Name of the Indicates a One list named “All TV” containing all channels, and another Channel list closed satellite named “Free TV” containing only free channels. In the “All TV”...

  • Page 26: Tv Release (0)

    VIEWING MODE TV release (0) With the 0 button you can toggle between analogue terrestrial TV, video, analogue and digital satellite TV signals. (This is only valid if the units are connected via SCART cables, and not by a RF connection.) Video recording Please note, that during the recording of a programme, every- thing shown on the screen will be registered! For example, if you...

  • Page 27: Main Menu

    MAIN MENU General Information Many of the functions of the Mediamaster are available from the Main Menu. Press MENU to open it. TV and Radio Channels Please refer to “List of TV and Radio channels” on page 25. Edit Channels From these menus you can create and edit channel lists.

  • Page 28

    MAIN MENU Create list From here you can create your own favourite lists, containing the channels you watch most frequently. You can give each list a spe- cific name, e.g. “Sport” or “Films.” When a favourite list is selected, you see only those channels defined in the list.

  • Page 29

    MAIN MENU Select Channels From this menu you add and remove the channels in your Favour- ite Lists. You use the “All TV” or “All Radio” list as basis to se- lect the channels from. A channel is added or removed by pressing the OK button. The square to the right on a line will be empty for removed channels, and will contain an “x”...

  • Page 30

    MAIN MENU Rearrange Channels From here you can arrange the sequence for the channels within your favourite lists. • With , mark the channel you want to move to a new posi- tion within the list. • Press again and the right side of the marked channel will change to •...

  • Page 31: Update Channels

    While watching a channel, first press OK, then the i button. Update channels via a PC It is also possible to update new channels via internet and a PC. You will find information how this is done on the URL GB 31...

  • Page 32: Guide

    MAIN MENU Guide Please refer to description on page 24. System Configuration You will be asked to enter your access code before you can en- ter this menu. The code is preset to 1234 from the factory. (The code can be changed from the Parental Control menu. Re- fer to page 38.) If you want to customize the system to suit you better, you can specify some settings from the submenus in the “System Con-...

  • Page 33

    MAIN MENU Manual Search When you perform a Manual Search you first need to enter some parameters for the channel search to work. The information you need to enter in this menu is available in magazines covering satellite TV reception, on the Internet or from your Service Provider.

  • Page 34: Edit Satellites

    MAIN MENU Edit Satellites When a new satellite has been sent into orbit, or if you select a not preprogrammed satellite, you can add it to the existing sat- ellite list. To add a new satellite • Select the line “New Satellite”. •...

  • Page 35

    MAIN MENU When your antenna is controlled by a motor: • Enter the “Channel Search” menu. • Select “Manual” or “Advanced” search. • Select the new satellite name. • Enter the settings for Transponder frequency, Polarization etc. for the new satellite. •...

  • Page 36: Antenna/satellite Configuration

    MAIN MENU Antenna/Satellite Configuration The procedure is the same as performed during the First Time In- stallation. Please refer to page 16. TV Settings From here you can adjust settings concerning your TV. TV screen format Select your TV screen format. The 4:3 format is the standard format for most TV screens.

  • Page 37: Receiver Upgrade

    Enter this menu to check for new software. If new software is available you will get information in the menu on how to proceed. If you download new software from ”Nokia Internet pages”, you transfer the software from the computer to the Mediamaster via the serial port.

  • Page 38: Parental Control

    1234. DO NOT FORGET IT! Without it you do not have ac- cess to any of the functions where the code is required! If you forget it, you have to contact an Authorized Nokia Service Center to get help.

  • Page 39: Appearance Preferences

    MAIN MENU Appearance Preferences Banner time-out When you switch channels, an information banner will be shown for a few seconds. You can select for how long the banner will be shown. Volume bar Select whether or not you want the volume bar to appear on the screen when you change the volume.

  • Page 40: System Information

    MAIN MENU System Information If you have to contact your service provider or a service center, they might ask for information available from this menu. There- fore, it is important that you first check the information in the following menus. System Information This gives general information about which hardware and soft- ware version your Mediamaster is running on.

  • Page 41: Conditional Access

    MAIN MENU Conditional Access This menu will only be activated if you have inserted a valid Smart- card in the slot behind the front lid. If more than one CA system is activated, select the one from which you want information. The Viaccess Conditional Access (CA) System is embedded in the Mediamaster.

  • Page 42: Glossary

    GLOSSARY OF TERMS Access Network Authorisation to use the coding system to purchase / A number of digital channels transmitted from one order TV programmes. source. Grouped under separate headings in the chan- nel list. Automatic Gain Control. Parental control A feature that allows parents to ”lock”...

  • Page 43

    PROBLEM SOLVING Problem Possible causes What to do The display on the front panel does Mains cable is not connected. Check that the mains cable is not light up/is not lit. plugged into the power socket. No sound or picture, but the front The Mediamaster is in standby Press the standby button or any panel shows the time or - - : - -.

  • Page 44: Problem Solving

    PROBLEM SOLVING Problem Possible causes What to do The remote control is not working. Battery exhausted. Change the batteries (both). Remote control is incorrectly Aim the remote control at box. aimed. Check that nothing blocks the front panel. The Mediamaster is in standby Check if (.) is flashing on the front mode.

  • Page 45: Technical Specifications

    TECHNICAL SPECIFICATIONS Transmission Conditional access system Standards DVB, MPEG 2 Embedded Viaccess and one PCMCIA interface for a Common Interface CA module (DVB Standard) LNB / Tuner input Smartcard Interface Connector 1x F-type (LNB) Interface for one card according to ISO 7816 RF input frequency 920-2150 MHz Supports embedded descrambler Viaccess...

  • Page 46: Menu Screen Structure

    MENUS SCREEN STRUCTURE First time installation Language Antenna/Satellite Selection RF Modulator Channel Search Progress English Antenna with one LNB for ASTRA Antenna Adjustment: TV Channels Radio Channels Welcome Signal Check: Svenska Normal Antenna with one LNB for Hotbird 101 CNN Radio Deutsch Antenna with one LNB for Sirius SPORT...

  • Page 48: Important Information

    Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead: not simply over the two wires. If in doubt, consult a qualified electrician. Nokia is a registered trademark of Nokia Corporation 66 76932-31...

Comments to this Manuals

Symbols: 0
Latest comments: