Download  Print this page
   

Advertisement

Electrolux Outdoor Products
Via Como 72
23868 Valmadrera (Lecco)
ITALIA
Phone + 39 0341 203111 - Fax +39 0341 581671
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.
Electrolux Outdoor Products manufacture products for a number of well known brands under various registered patents, designs and
trademarks in several countries.
© Electrolux Outdoor Products
The Electrolux Group. The world's No.1 choice.
The Electrolux Group is the world's largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million
Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are
sold each year to a value of approx. USD 14 billion in more than 150 countries around the world.
PN. 249453 REV. 00 (04/04)
MAC 538E / MAC 539E
38 CC
MAC 540E / PROMAC 40 II
40 CC
A.
MAC 542E / CALIFORNIA
42 CC
MAC 545E / PROMAC 46 II
46 CC
P 538E / EUROMAC S42 / S44
38 CC
P 540E
40 CC
P 542E / EUROMAC S43
42 CC
P 461 II / TITANIUM 460
46 CC
B.
C.
D.

Advertisement

Table of Contents

   Also See for Electrolux MAC 538E

   Summary of Contents for Electrolux MAC 538E

  • Page 1 MAC 538E / MAC 539E 38 CC MAC 540E / PROMAC 40 II 40 CC MAC 542E / CALIFORNIA 42 CC MAC 545E / PROMAC 46 II 46 CC P 538E / EUROMAC S42 / S44 38 CC P 540E...
  • Page 2 Due to a constant product improvement programme, the factory reserves the right to modify technical details MAC 540E - MAC 542E mentioned in this manual without prior notice. MAC 538E - MAC 539E California - MAC 545E Promac 40 II Im Sinne des Fortschritts behält sich der Hersteller das Recht vor, technische Änderungen ohne vorherigen Hinweis...
  • Page 3: Safety Precautions

    A. General description 1 - BAR 13 - BAR RETAINING NUTS 2 - CHAIN 14 - CHAIN CATCHER 3 - FUEL TANK CAP 15 - MUFFLER SHIELD 4 - OIL TANK CAP 16 - REAR HANDLE 5 - STOP SWITCH 17 - THROTTLE TRIGGER LOCKOUT 6 - STARTER HOUSING 18 - THROTTLE TRIGGER...
  • Page 4 Do not cut with the end on the bar, Choke partially opened this may cause kickback Never use the machine with only one Choke closed (cold start) hand Always use the machine with both Stopping hands Switch off the engine by moving the stop switch to the STOP position Brake engaged / disengaged before carrying out any checks...
  • Page 5 6 Keep by-standers and animals out of the work area; at a If this is not possible, it is recommended that users operat- minimum distance of 10 m or twice the timber length. If ing chainsaws in remote areas carry an adequate first-aid kit necessary, use warning signs to keep on-lookers at a dis- with them and ensure someone knows their location.
  • Page 6 E. Starting and stopping IMPORTANT Pull the starter rope until the engine starts. Allow engine to warm up for ten seconds for better cutting Never start or operate unless bar and chain are properly performance. installed. Before starting always move the saw away Squeeze the throttle trigger (G) to release the throttle from the fuelling area and place it on a firm, flat surface, the guide bar to the front.
  • Page 7 Then open screw 1 full turn (counterclockwise) . • I: The I (IDLE) screw controls the throttle opening to gov- If acceleration is not smooth, open another 1/8 turn to ern idle speed (2800 min ) adjust as necessary. increase fuel flow . CAUTION: increased idle speed may cause chain move- •...
  • Page 8 The chain brake should snap into both positions.If 3 CHAIN CATCHER strong resistance is felt or lever does not move into This unit is fitted with a chain catcher below the drive either position, DO NOT USE YOUR SAW. Take it imme- spocket.
  • Page 9 Fault finding table Engine will not start Engine runs badly The chainsaw runs Engine runs badly or but does not cut well looses power when cutting Check STOP switch • is in the position I. Control fuel level • • min.

Comments to this Manuals

Symbols: 0
Latest comments: