Gigabyte GR-EZI04H User Manual

OS Installation Steps Specification
Hardware
1. Regarding USB recorder installation, please connect USB signal cable in
USB 2.0 port, USB power cable in USB 3.0 port. (Blue color)
Processor : Intel D2550 1.86GHz Dual-Core processor
Memory : DDR3 4GB
2. Connect USB keyboard in USB 3.0 port (Blue color) and USB mouse in USB
Internal HDD : 3.5" SATA II x 4 Hot-swappable
2.0 port, please refer to below picture.
I/O Interface : 2 x RJ45, 2 x USB 2.0, 2 x USB 3.0,
1 x D-Sub VGA
LAN : 2 x 10/ 100/ 1000Mbps
USB Keyboard
PC Operating System Support
USB Recorder
File sharing for computers running on:
Signal Cable
Remote access & system backup to computers running on: Microsoft Windows 7 32 & 64-bit
3. Leave one hard disk drive in HDD tray 1 and remove hard disk drives in
other HDD tray.
4. If you have changed BIOS item "SATA Con guration", please power-on
the GR-EZI14H, then press F2 to enter BIOS setup utility menu.
VDI (virtual desktop infrastructure) is enabled to let users connect to system by their notebook or tablet devices,
sharing applications on GR-EZI14H.
5. Switch to "Advanced" screen and view "SATA Con guration" item.
6. The setting of "SATA Mode" should be "AHCI Mode", this is factory default
Warranty
value, showed as following. If the setting is di erent, change it to "AHCI
1 year limited hardware warranty and software technical support.
Mode", and then save to exit.
To extend warranty, please contact GIGABYTE sales team.

Package Contents

7. Power-o the GR-EZI14H.
8. Put "Windows Home Server 2011 Disc 1" into USB DVD-ROM, and connect
it to GR-EZI14H.
Main unit x 1 (screws, key & Disk label in HDD tray)
9. Power-on the GR-EZI14H again, then press F10 to open boot menu.
Create Windows Home Server 2011 Software RAID Power & NetworkConnections
1. To use RAID mode, after recovery setup, install hard disk drives in other
HDD tray, and then press power button to boot up the GR-EZI14H.
2. Click on "Start" menu and select "Computer".
Cable / ADSL / VDSL modem
Internet
or
Cable port on the wall
3. Click on USB mouse right button to open "Manage" item.
4. Open "Disk Management" item.

Installing an Internal Hard Disk

Please refer to the following figure how to install an internal hard disk of GR-EZI04H.
5. Select "Disk 1" to create RAID mode
Recovery Steps
We could restore "Windows Home Server 2011" as factory default without installation disc.
1. Connect keyboard and mouse to GR-EZI14H via USB.
2. Leave one HDD in tray 1 and remove HDDs in other tray.
3. Power-on the GR-EZI14H.
4. After the booting screen appearing, keep to press F1 until vanish.
(Warning) If you install a hard disk that contains data, please back it up before installation just in case.
5. Following steps are the same from step 11 of operation system installation.
10. Select your USB DVD-ROM or USB DVD recorder with pre x "UEFI: " as
boot device, example as following
Size (HxWxD) : 220 x 183.5 x 146.5 (mm)
Weight : 3.5kg excluded HDD
Max Internal Capacity : 16TB (4 x 4TB)
Front LED : 1 x PWR, 1 x SYS, 1 x EXT, 4 x HDDs, 2 x LANs
Power : External 90W power adapter
USB Recorder
Power Cable
USB Mouse
Microsoft Windows 7 32 & 64-bit
Microsoft Windows Vista 32 & 64-bit
11. The installation screen would display after you pressed enter key.
Microsoft Windows XP Home SP2
Microsoft Windows XP Professional SP3
Mac OS X or later
Microsoft Windows Vista 32 & 64-bit
Microsoft Windows XP Home SP2
Microsoft Windows XP Professional SP3
12. Click "Start WHS2011 Recovery" button to start, and click "OK" to con rm.
13. Replace "Windows Home Server 2011 Disc 2" to continue.
Adapter & Power cord x 1
6. Such as New RAID-5 Volume, click on "Next" as below screenshot.
IP Router
7. Click on "Add" to add Disk 2 and Disk 3 in "Selected:"
PC or Notebook
8. Click on "Next".
Power cable
01.
9. Click on "Next". Open the bezel door.
02.
Press the release button.
Pull the locking lever and remove the
03.
HDD tray.
04.
Slide hard disk into blank.
Secure the hard drive to the tray with
4 screws as shown. Do not over tighten
05.
the screws. Slide the blank into the bay
until it locks into place.
06.
Press power button to boot up.
Getting familiar with your unit
GR-EZI04H Front View
Key Lock Front Panel LED
Front LED
1) System LED
1 2
2) External LED
3 4
5 6 3~4) LAN LED
7 8
5~8) Disk LED
9
9) Power LED
RJ-45 LAN cable x 2
Cautions & Checklist
Back up your system periodically to avoid any potential data loss. GIGABYTE disclaims any responsibility of all sorts of data loss or
recovery. Should you return any components of GR-EZI04H package for refund or maintenance, make sure they are carefully
packed for shipping. Any form of damages due to improper packaging will not be compensated.
Do's and Don'ts
GR-EZI04H can operate normally in the temperature
of 5 ~35 and relative humidity of 0%~90%.
℃ ℃
Please make sure the environment is well-ventilated.
The power cord and devices connected to
GR-EZI04H must provide correct supply voltage.
Do not place any objects on top of the GR-EZI04H as
this may cause overheating and interfere it's normal
operation.
Do not place GR-EZI04H near any liquids. Do not
place GR-EZI04H on any uneven surfaces as to avoid
it falling o and getting damaged.
Do not attempt to repair your GR-EZI04H under any
conditions. Improper disassembly or the product
may expose you to electric or other risks.
14. Remove DVD-ROM and click "OK" to reboot machine after installation.
GR-EZI04H Rear View
15. It will enter the setup phase and please wait to completion.
VGA D-Sub USB 3.0 USB 2.0
Description
Solid Blue: System is power-on
When device is plugged in USB 3.0 port
16. DO NOT login while setup, and it will power-o itself after completion.
Solid Blue: Network link / Blinking Blue: Network activity
Solid Blue: Disk detected
Blinking Blue: Disk activity
Solid Blue: System power ON
17. Windows Home Server 2011 OS username and password both "password".
18. You can read detailed user's manual les in the Recovery disc #2 "USER'S
MANUAL" folder.
19. Regarding Windows Home Server 2011 operation system product key and
OVD software activation code, please check the NAS chassis bottom side's
label.
10. Click on "Next".
Use the at head screws in the product package to
secure the hard disks into the GR-EZI04H.
Do not place GR-EZI04H in direct sunlight or near
chemicals. Make sure the temperature and
humidity of the environment are in optimized level.
11. Click on "Finish".
Risk of explosion if battery is replaced by an
incorrect type. Dispose of used batteries according
to the instructions.
Unplug the power cord and all connected cables
before cleaning. Wipe GR-EZI04H with a damp
towel. Do not use chemical or aerosol to clean
GR-EZI04H.
12. After you con rmed below information, click on "Yes".
For any enquiries, please contact the distributor.
13. You can see Disk 1, Disk 2 and Disk 3 resynching.
LAN Port DC-In
PN: ooxx-ooo-xxxx