Programming Your Thermostat; Planning Your Program - White Rodgers 1F85RF-275 Quick Installation Manual

OPERATING YOUR THERMOSTAT AND REMOTE SENSOR
Remote Sensor Operation
The sensor monitors the temperature and sends information
to the thermostat. Updated information is sent to the thermo-
stat when the temperature changes 3/16 degree or more
from the last update. If the temperature does not change for
10 minutes, the sensor will transmit to assure communica-
tion.
Low Battery power: The sensor will display the word LO
along with BATT icon to indicate a low battery power
condition. The 2 "AAA" batteries must be replaced to ensure
a proper sensor performance. For optimum performance,
replace batteries once a year with new premium brand
alkaline batteries such as Duracell
Thermostat Setpoint Offset: The thermostat displayed
setpoint can be offset using the remote sensor
buttons. The remote setpoint offset is defaulted to 0 (zero).
Press to increase the setpoint up to 4
press to decrease the setpoint up to 4
the last button press, the remote sensor will delay for ten
seconds and then transmit the setpoint offset information.
When the thermostat receives the offset information, it will
start a remote sensor temporary hold for the length of time
set in the Remote Sensor Configuration Menu, item 2. The
setpoint temperature will be changed by the amount of offset
transmitted. HOLD on the thermostat will flash and HLD on
the sensor will display for the period of the hold. The remote
sensor Thermostat Setpoint offset can be cancelled at any
time by pressing the thermostat RUN button.
PERIOD WEEKDAYS (5 DAYS)
START
TIME
MORN 6:00 AM
DAY 8:00 AM
E V E 5:00 PM
NITE 10:00 PM
MORN 6:00 AM
DAY 8:00 AM
E V E 5:00 PM
NITE 10:00 PM
PERIOD WEEKDAYS (5 DAYS)
START
TIME
MORN
DAY
EVE
NITE
MORN
DAY
EVE
NITE
16
® or Energizer ® .
and
o
(four bars C) or
o (four bars H). After
FACTORY PROGRAM
SATURDAY (1 DAY)
REMOTE START
TEMP WEIGHT TIME
70 F A 6:00 AM
62 F A 8:00 AM
70 F A 5:00 PM
62 F A 10:00 PM
78 F A 6:00 AM
85 F A 8:00 AM
78 F A 5:00 PM
82 F A 10:00 PM
PERSONAL PROGRAM
SATURDAY (1 DAY)
REMOTE START
TEMP WEIGHT TIME

PROGRAMMING YOUR THERMOSTAT

This section will help you plan your thermostat's program to
meet your needs. For maximum comfort and efficiency, keep
the following guidelines in mind when planning your program.
• When heating (cooling) your building, program the temper-
atures to be cooler (warmer) when the building is vacant or
during periods of low activity.
• During early morning hours, the need for cooling is usually
minimal.

Planning Your Program

Look at the factory preprogrammed times and temperatures
shown in the sample schedule. If this program will suit your
needs, simply set the time and day and press the RUN
button to begin running the factory preset program.
If you want to change the preprogrammed times and tem-
peratures, follow these steps.
Determine the time periods and temperatures for your
program. You must program four periods for each day.
However, you may use the same heating and cooling
temperatures for consecutive time periods. You can choose
start times, heating temperatures, and cooling temperatures
independently (for example, you may select 5:00 AM and 70°
as the weekday 1st period heating start time and tempera-
ture and also choose 7:00 AM and 76° as the weekday 1st
period cooling start time and temperature).
Use the table to plan your program time periods and the
temperatures you want during each period. Fill in the
complete table to have a record of your programs.
SUNDAY (1 DAY)
REMOTE START
TEMP WEIGHT TIME
70 F A 6:00 AM
62 F A 8:00 AM
70 F A 5:00 PM
62 F A 10:00 PM
78 F A 6:00 AM
85 F A 8:00 AM
78 F A 5:00 PM
82 F A 10:00 PM
SUNDAY (1 DAY)
REMOTE START
TEMP WEIGHT TIME
REMOTE
TEMP WEIGHT
70 F A
62 F A
70 F A
62 F A
78 F A
85 F A
78 F A
82 F A
REMOTE
TEMP WEIGHT