Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Installation Manual
Advertisement
Table of Contents
Related Manuals for Sanyo VA-82LAN
Summary of Contents for Sanyo VA-82LAN
- Page 1 VA-82LAN INSTRUCTION MANUAL Option Board ( Network...
-
Page 2: Table Of Contents
Table of Contents Instruction ....................2 ■ System requirements ..................2 Flow of Camera Operation through to Network Operation ...... 3 ■ User names and operating privileges ............. 4 Configuring the TCP/IP Settings on PC ............. 5 Accessing the Camera ................7 ■... -
Page 3: Instruction
Windows Update service. Copyright notice This instruction manual is copyrighted by SANYO Electric Co., Ltd. No materials contained in this manual may be reproduced in any format without the prior permission of the copyright holder. Microsoft, Windows and Internet Explorer are registered trademarks or trademarks of Microsoft Corporation in the United States and other countries. -
Page 4: Flow Of Camera Operation Through To Network Operation
Flow of Camera Operation through to Network Operation For detailed instructions on individual procedures, refer to the pages shown below. 1 Installing the option board on the camera Refer to the supplied “INSTALLATION MANUAL” for how to install the option board on the camera and make connection using LAN cables. -
Page 5: User Names And Operating Privileges
Flow of Camera Operation through to Network Operation ■ User names and operating privileges Two types of user name shown below can access the camera and are authenticated by password during the login process. The operations that the user can perform for the camera depend on the user name used to access the camera. Password Operation privileges User name... -
Page 6: Configuring The Tcp/Ip Settings On Pc
Configuring the TCP/IP Settings on PC Perform the appropriate TCP/IP settings on your PC in accordance with your operating system. In the [Control Panel], click [Network and Right-click on the LAN interface Internet Connections]. (Ethernet adapter) configuration used for accessing the camera and click [Properties] in the context menu. - Page 7 Configuring the TCP/IP Settings on PC Click [Properties]. Preparing the Web Browser for Accessing the Camera [General] tab appears in the [Internet Protocol (TCP/IP) Properties] dialog box. Web browser is required to access the camera. Install Internet Explorer Ver.6.0 or higher on your PC. Select the [Use the following IP In the cases below, perform the Internet Explorer’s address:] radio button and complete the...
-
Page 8: Accessing The Camera
Accessing the Camera Start the Web browser. Select the language used for display. To access the camera, Internet Explorer Ver.6.0 or Available languages: higher is required. English, French, German, Spanish, Japanese Note: When Internet Explorer is used for accessing the camera, the number of images sent from the camera may be limited. -
Page 9: Accessing The Camera Using The Upnp Connection
“ON” (see page 39). window: • The factory setting value is “ON”. SANYO Camera - (camera title) In the (camera title) section above, the title specified for the camera in [TITLE] field of the [NETWORK SETTINGS] screen appears. -
Page 10: Structure Of Main Screen And Function Of Each Section
Structure of Main Screen and Function of Each Section The structure of the main screen partially differs depending on the screen display types (ActiveX/HTML). Although the HTML screen is the initial display after login, the display type can be switched with the selection button on the control panel (see page 12). - Page 11 Structure of Main Screen and Function of Each Section 1 Control panel (See pages 11 - 12) 6 Voice control buttons (See page 13) Used to perform remote operation of the camera. Allows you to enable or disable the voice input/ output (send/receive ON/OFF) respectively as well 2 Camera title (See page 17) as adjust the volume.
-
Page 12: How To Use The Control Panel
How To Use the Control Panel You can operate the camera remotely with the control panel. Note: • The admin users alone can operate all the functions of the control panel. For the guest users, only parts of the control panel are displayed. •... - Page 13 How To Use the Control Panel 3 RESOLUTION 9 AUX Specifies the video resolution at five levels. These buttons are reserved for additional functions. (At three levels when the image compression format The function corresponding to the number selected is “H.264”.) in the pull-down menu will be performed.
-
Page 14: Establishing Voice Communication
Establishing Voice Communication You can establish bi-directional voice communication between the camera and PC. <Camera → PC> Voice control buttons You can view live video with voice because the voice picked up by the microphone on the camera is output to the PC speakers. -
Page 15: Other Operations On The Main Screen
Other Operations on the Main Screen ■ Changing the orientation of the camera Clicking the video image changes the orientation of the camera so that the point where you click moves to the center of the image. (Operation example) ■ Capturing the still image from the live video (Capture button 1) The capture button displays the still image at the moment of clicking the button in a separate window. -
Page 16: Operations On Configuration Screen
Operations on Configuration Screen (“admin” only) When you click the [MAIN SETTINGS] button on the control panel, the menu buttons for an administrative user (“admin”) are displayed. Clicking each button displays the corresponding configuration screen. The menu button being selected is displayed in orange. 06/14/2007 01:49:14 06/14/2007 01:49:14 06/14/2007 01:49:14... - Page 17 Operations on Configuration Screen (“admin” only) 7 DDNS (See page 33) Used for configuring the DDNS settings when using the DDNS service. 8 SCHEDULE (See pages 35 - 38) Used for configuring the schedule settings, including the alarm notification, the alarm image transmission and timer transmission in the FTP mode, and the auto-mode setting of the camera.
-
Page 18: Network Settings
NETWORK SETTINGS (“admin” only) 1 TITLE 3 SUBNET MASK Specifies the camera title. When the [IP ADDRESS] setting is “FIX”, enter the The title specified here appears in the main screen subnet mask. and is inserted into the alarm notification e-mail. The title can be up to 16 alphanumeric characters. - Page 19 NETWORK SETTINGS (“admin” only) 6 DNS F PASSWORD When the [IP ADDRESS] setting is “DHCP”, select Specify the login password according to each user the method for configuring the DNS server address. name (guest/admin). MEMO: Manually configure the DNS server address.
-
Page 20: Security Settings
SECURITY SETTINGS (“admin” only) When you click the [SECURITY] button on the [NETWORK SETTINGS] screen, the [SECURITY SETTINGS] screen appears. You can set the camera access restriction to the PC. 1 SECURITY FUNCTION 4 Setting of Access Restriction Select “ON” when you set the access restriction. Sets the access restriction to the registered PCs individually. -
Page 21: Clock Settings
CLOCK SETTINGS (“admin” only) [REFRESH] button 1 CLOCK SET 3 DATE/TIME FORMAT Set the date and time on the internal clock of the Sets the date and time display format. camera. (Y/M/D, M/D/Y, D/M/Y) MEMO: 4 TIME ZONE The days of week are automatically displayed based Selects the area where the camera is used. - Page 22 CLOCK SETTINGS (“admin” only) 6 DAYLIGHT SAVING (ON/OFF) 8 NTP settings According to the [TIME ZONE] setting, the date and Configuration of the NTP settings are possible only time settings of start (ON) and end (OFF) of the when the [CLOCK ADJUST] preference is set to daylight saving mode are automatically displayed in “ON (NTP)”.
-
Page 23: Codec/Streaming
CODEC/STREAMING SETTINGS (“admin” only) 1 DYNAMIC FIELD FRAME CONVERSION • Buffering alarm data • Multiple users are accessing Enables/Disables the DFFC (function to reduce jaggedness of the edge of moving • While distributing H.264 images in multicast (When [MULTICAST SET] is turned “ON” for objects). - Page 24 CODEC/STREAMING SETTINGS (“admin” only) 4 STREAMING 5 [SET] button Specifies the streaming conditions of H.264 After completing the settings, click this button image. to confirm the settings. • PROTOCOL Sets the transmission protocol (UDP 6 [CANCEL] button (Unicast) or HTTP) of H.264 images. To restore the original settings, click the •...
-
Page 25: Audio Settings
AUDIO SETTINGS (“admin” only) 1 AUDIO INPUT 3 AUDIO PORT NUMBER Outputs audio from the camera to PC. Set the number of the port for voice To output audio, select “ON”. communications. • MIC SENSITIVITY Note: Sensitivity for the microphone connected •... -
Page 26: E-Mail Settings
E-MAIL SETTINGS (“admin” only) 1 SEND MESSAGE 4 RECIPIENT MAIL ADDRESS When sending the e-mail, set this value to Specifies the recipient’s e-mail address to “ON”. which the e-mail is sent. You can specify up to five e-mail addresses. 2 Mail server configuration 1 Type the recipient’s e-mail address and The following mail server information is check the check box to the left of the... - Page 27 E-MAIL SETTINGS (“admin” only) 3 Clicking [TEST] sends test mails to all the 7 TIMER transmission destinations whose check Specifies the preferences for sending box is selected. “TEST” is displayed in the notification e-mail using the timer. subject of test mails. E-mails are sent automatically at the interval specified in [TX RATE].
-
Page 28: Image Transfer Settings
IMAGE TRANSFER SETTINGS (“admin” only) ■ Image Transfer Mode When the [IMAGE TRANSFER SETTINGS] screen appears, select the image transfer mode in [IMAGE TRANSMISSION], and display each setting screen. • OFF: Image transmission is disabled. • HTTP: Transfers the image to the recording/playing software (VA-SW3050), which is optionally available. -
Page 29: For Http Connection
IMAGE TRANSFER SETTINGS (“admin” only) ■ For HTTP connection When you record and play video in the HTTP mode, configure the recording conditions on the screen of “VA-SW3050”. 1 IMAGE TRANSMISSION 3 ALARM Set the image transfer mode to “HTTP”. 1 Sets the image conditions as well as activates/deactivates the voice recording 2 LIVE/NORMAL RECORD... - Page 30 IMAGE TRANSFER SETTINGS (“admin” only) 2 Select the [BUFFER SIZE] option for specifying the buffering capacity for recording each alarm image. According to the value you select, perform the following settings: When the [BUFFER SIZE] setting is set from “0.5MB to 8MB” One alarm image set containing both the pre- and post-alarm images is stored in the camera, and then the alarm image set is...
-
Page 31: For Ftp Connection
IMAGE TRANSFER SETTINGS (“admin” only) ■ For FTP connection 1 IMAGE TRANSMISSION 2 Configuring the FTP information Set the image transfer mode to “FTP”. The following FTP information is specified in these setting items. • PORT NUMBER Please set the same number as the control port number configured on the server. - Page 32 When the alarm is detected, only the • If the CAMERA ID is not configured, post-alarm images will be transferred to “sanyo” and “alarm” are substituted the FTP server at the interval you specified as the file name and folder name in the [TX RATE] setting.
- Page 33 “<”, “>”, “?”, “|”, “*”, “:” (colon) and “;” and time information is not displayed. (semicolon). • If the CAMERA ID is not configured, “sanyo” and “timer” are substituted as the file name and folder name respectively. • OVERWRITE Configures whether or not to overwrite file data transmitted to the FTP server.
-
Page 34: Ddns Settings
DDNS SETTINGS (“admin” only) 1 DDNS 7 LOG If you use the SANYO’s DDNS service, select “ON”. The log of one DDNS update history is The setting screen will open. displayed. 2 [REGISTER] button 8 [SET] button Clicking the [REGISTER] button will access the After completing the settings, click this button SANYO’s DDNS service site. - Page 35 They are required to register the domain name. Click the [REGISTER] button. Clicking the button automatically accesses the SANYO’s DDNS service site, and the [LOG IN] screen appears. Enter the Domain Name to be used and click [Submit]. The domain name has been registered in the DDNS server.
-
Page 36: Schedule Settings
SCHEDULE SETTINGS (“admin” only) The schedule function works according to the time set on the option board (the time displayed in the main screen). After you turn on/off the camera, configure the exact time on the CLOCK SETTING screen. ■ SCHEDULE Specify the schedule for sending the notification e-mail using the timer and sending the alarm notification. - Page 37 SCHEDULE SETTINGS (“admin” only) 3 Specifying the function to be performed 7 [FTP SETTING] button The specified schedule can be applied to the Displays the [IMAGE TRANFER SETTINGS] following five functions. screen. • TIMER (SMTP) MEMO: Enable/disables the e-mail transmission The alarm image transmission and timer using the timer.
-
Page 38: Auto Mode Schedule
SCHEDULE SETTINGS (“admin” only) ■ AUTO MODE SCHEDULE The auto-mode function operates the camera at the scheduled time automatically according to the specified operation pattern. You can specify up to two auto-mode operation patterns per day. 1 Day of the week (WEEK) 4 [COPY] button Enables/disables the schedule function and Copies the setting of the selected row. -
Page 39: Holiday Settings
SCHEDULE SETTINGS (“admin” only) ■ HOLIDAY SETTINGS Specifies the dates you want to treat as holidays. 1 HOLIDAY Specifies the day of the week you want to treat as holiday. The default setting is [SUN]. 2 MONTH/DAY Specifies the dates you want to treat as holidays. -
Page 40: Option Settings
OPTION SETTINGS (“admin” only) Version number 1 UPnP Note: • Neither make any operations on the screen When you access the camera through the nor turn power off while the “LOADING UPnP connection, make sure that the [UPnP] FIRMWARE FILE...” message is displayed. option is set to “ON”... - Page 41 OPTION SETTINGS (“admin” only) 3 RESTORING FACTORY SETTINGS All the settings made in the screens can be reset to the factory setting values. Click the [SET] button to display the dialog for confirming the operation. Click the [OK] button. When the restoration process is completed, the camera is disconnected automatically, and then connected again automatically in 40 seconds.
-
Page 42: Changing The Camera Settings
Changing the Camera Settings (“admin” only) Clicking on the control panel displays the on-screen camera configuration menu. You can change the monitoring and operation preferences stored in the camera through the network connection. (You cannot change the TOUR operation preferences on this menu.) MEMO: The menus displayed depend on the camera model. -
Page 43: Settings List
Settings List Screen Setting menu Options ENGLISH, FRANÇAIS, DEUTSCH, Language selection screen Display language ESPAÑOL, JAPANESE <JPEG> NTSC: 720×240, 640×480, 360×240, 176×120, 720×480 PAL: RESOLUTION 720×288, 640×480, 360×288, 176×144, 720×576 <H.264> NTSC: 720×480, 352×240, 176×144 Main screen PAL: 720×576, 352×288, 176×144 BASIC, NORMAL, ENHANCED, FINE, PICTURE QUALITY SUPER FINE... - Page 44 Settings List Screen Setting menu Options [MAIN SETTINGS] screens Week: LST, 1ST, 2ND, 3RD, 4TH WEEK Days of the week: SUN - SAT DAYLIGHT SAVING MONTH JAN - DEC (ON/OFF) CLOCK TIME Hour (00 - 23), minute (00 - 59) SETTINGS CLOCK ADJUST OFF, ON (NTP), LOGIN (PC)
- Page 45 Settings List Screen Setting menu Options [MAIN SETTINGS] screens USER ID – (up to 48 characters) PASSWORD – (up to 20 characters) POP3 SERVER ADDRESS – (up to 64 characters) ALARM OFF, ON, SCHEDULE – (up to 16 double-byte or 32 single-byte characters) SUBJECT E-MAIL –...
- Page 46 Settings List Screen Setting menu Options [MAIN SETTINGS] screens ALARM NTSC: 176 x 120, 360 x 240, 720 x 240, 640 x 480, 720 x 480 RESOLUTION PAL: 176 x 144, 360 x 288, 720 x 288, 640 x 480, 720 x 576 BASIC, NORMAL, ENHANCED, FINE, PICTURE QUALITY...
- Page 47 Settings List Screen Setting menu Options [MAIN SETTINGS] screens TIMER SMTP OFF, ON OFF, ON ALARM SCHEDULE SMTP OFF, ON OFF, ON REMOTE ALARM OFF, ON "ACTIVE" SCHEDULE ---, SEQ, PAN, TOUR, PRESET, AUX ON, COMMAND SETTINGS AUX OFF A - D 1 - 4 AUTO MODE TOUR...
-
Page 48: Openssl License
OpenSSL License The following license is applied to OpenSSL. LICENSE ISSUES ============== The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit. See below for the actual license texts. Actually both licenses are BSD-style Open Source licenses. - Page 49 OpenSSL License Original SSLeay License ----------------------- /* Copyright (C) 1995-1998 Eric Young (eay@cryptsoft.com) * All rights reserved. * This package is an SSL implementation written * by Eric Young (eay@cryptsoft.com). * The implementation was written so as to conform with Netscapes SSL. * This library is free for commercial and non-commercial use as long as * the following conditions are aheared to.
-
Page 50: Specifications
Specifications JPEG/H.264 (simultaneous transmission available) Image compression H.264: Main Profile, Level 3 <JPEG> NTSC: 720×240, 640×480, 360×240, 176×120, 720×480 PAL: 720×288, 640×480, 360×288, 176×144, 720×576 Resolution <H.264> NTSC: 720×480, 352×240, 176×144 PAL: 720×576, 352×288, 176×144 Picture quality 5 levels <JPEG> NTSC: Max 30ips (720×480) PAL: Max 25ips (720×576) Frame rate... - Page 52 Printed on recycled paper 1AC6P1P3016-- SANYO Electric Co., Ltd. L9EBH/WA (0807KP)