Supermicro SuperStorage L-Serie Quick Reference Manual

SuperStorage L-Serie Quick Reference Guide
Board Layout
1 2 3 4 5 6 11 12 16
CPU2
20 JBT1
CPU2
CMOS CLEAR
Intel
PCH
21 X9DRD-7JLN4F
17
CPU2
18
CPU1
SP1
10
9 15 8 7
No.
Description
JBOD Expansion Port
1
CPU1 Slot2 PCI-E 3.0 x8
2
CPU2 Slot3 PCI-E 3.0 x8
3
4 CPU2 Slot4 PCI-E 3.0 x8
5 CPU2 Slot5 PCI-E 3.0 x8
CPU1 Slot6 PCI-E 3.0 x8
6
P1-DIMMA1(Blue)/P1-DIMMA2 slot
7
P1-DIMMB1 (Blue)/P1-DIMMB2 slot
8
9 P1-DIMMC1 (Blue)/P1-DIMMC2 slot
10 P1-DIMMD1 (Blue)/P1-DIMMD2 slot
11 P2-DIMME1 (Blue)/P2-DIMME2 slot
P2-DIMMF1 (Blue)/P2-DIMM F2 slot
12
13 P2-DIMMG1 (Blue)/P2-DIMM G2 slot
14 P2-DIMMH1 (Blue)/P2-DIMM H2 slot
15 CPU1 / P1 install first / minimum requirement
16 CPU2
17 SATA 3 Ports 0~1 (from Intel PCH)
18 SATA 2 Ports 2~5 (from Intel PCH)
19 SAS 2.0 ports 0~3, 4~7 (from LSI SAS 2308 Controller)
20 JBT1 = CMOS Reset
21 SATA DOM Power
MEMORY
Notch
14 13
Release Tab
Top View of DDR3 Slot
DIMM Module Population Tables
Processors and their Corresponding Memory Slots
C P U # C
CPU 1 (P1-) A1 B1 C1 D1
JPW3
CPU2 (P2-)
E1 F1 G1 H1
L-SAS4~7 L-SAS0~3 Processor and Memory Module Population
Number of CPU and Memory Population Confi guration Table
CPUs+DIMMs (For memory to work properly, please install DIMMs as shown below.)
1 CPU & CPU1
3 DIMMs P1-A1/P1-B1/P1-C1
1 CPU & CPU1
JPW1 6 DIMMs
P1-A1/P1-B1/P1-C1/P1-D1/P1-A2/P1-B2
1 CPU & CPU1
9 DIMMs P1-A1/P1-B1/P1-C1/P1-D1/P1-A2/P1-B2/P1-C2/P1-D2/P1-A3
19
1 CPU & CPU1
12 DIMMs P1-A1/P1-B1/P1-C1/P1-D1/P1-A2/P1-B2/P1-C2/P1-D2/P1-A3/P1-B3/P1-C3/P1-D3
2 CPUs & CPU1 + CPU2
6 DIMMs P1-A1/P1-B1/P1-C1
P2-E1/P2-F1/P2-G1
2 CPUs & CPU1 + CPU2
12 DIMMs P1-A1/P1-B1/P1-C1/P1-D1/P1-A2/P1-B2
P2-E1/P2-F1/P2-G1/P2-H1/P2-E2/P2-F2
2 CPUs & CPU1 + CPU2
16 DIMMs P1-A1/P1-B1/P1-C1/P1-D1/P1-A2/P1-B2/P1-C2/P1-D2
P2-E1/P2-F1/P2-G1/P2-H1/P2-E2/P2-F2/P2-G2/P2-H2
2 CPUs & CPU1 + CPU2
18 DIMMs P1-A1/P1-B1/P1-C1/P1-D1/P1-A2/P1-B2/P1-C2/P1-D2/P1-A3
P2-E1/P2-F1/P2-G1/P2-H1/P2-E2/P2-F2/P2-G2/P2-H2/P2-E3
2 CPUs & CPU1/CPU2
24 DIMMs P1-A1/P1-B1/P1-C1/P1-D1/P1-A2/P1-B2/P1-C2/P1-D2/P1-A3/P1-B3/P1-C3/P1-D3
P2-E1/P2-F1/P2-G1/P2-H1/P2-E2/P2-F2/P2-G2/P2-H2/P2-E3/P2-F3/P2-G3/P2-H3
Please refer to the user manual for more details on memory types, speeds and configurations
Chassis Front Panel LED Indicator Definition
Component State/Indication
Solid Green/Power is On
Power
Flash Green/Onboard SAS/SATA Drive Activity
Onboard SATA
LAN1 Flash Green/Network Connectivity
LAN2 Flash Green/Network Connectivity
Temperature/Fan Flash Red/Fan Failure; Solid Red/Over Temperature
Flash Red/Power Supply Failure
Power Failure
Notch
Front View
Note: Notch should align
with the receptive key
point on the slot.
Release Tab
Drive RED LED Indicator
LED State
OFF
Solid ON
Slow Blink (1 Hz)
r o e r s p o n d n i g M e m o y r l S t o 2 Fast Blink, Pause (repeats)
A2 B2 C2 D2 A3 B3 C3 D3 Fast Blink (4 Hz)
E2 F2 G2 H2 E3 F3 G3 H3
Beep Code/LED
1 beep
5 short beeps + 1 long
beep
5 long beeps + 2 short
beeps
1 continuous beep
LED Indicator
3.5" Drive Module
2.5" Drive Module
Blue/Activity
Red/Status
Indication
Normal Operation
Drive Failure
Rebuilding to Drive
Drive Assigned as a Hot Spare
Slot Identify command
has been issued from controller
Rear View
2
1 3 4 5 6 7
1. Place heatsink on top of installed CPU
2. Line up the four screws to socket
No. Description
3. Push down heatsink and screw down as shown
COM Port1 (cross pattern, in order: A, C, B, D)
1
4. NOTE: Only use 6-8 lb/f of torque; otherwise, hand-tighten
Dedicated IPMI LAN
2
each screw, to avoid damaging the system
USB 0/1/2/3 Ports
3
4 LAN 1/2/3/4 Ports
5 VGA Port

6 UID Button
IMPORTANT: See installation instructions and safety warning
7
Dual JBOD Expansion port *
before connecting system to power supply.
http://www.supermicro.com/about/policies/safety_information.cfm
* SSG-6027R-E1R12L features a single expansion port

!
Beep Codes
To reduce risk of electric shock/damage to equipment,
disconnect power from server by disconnecting all power
cords from electrical outlets.
BIOS Beep Codes If any CPU socket empty, install protective plastic CPU cap
Message Description

Refresh Circuits have been reset.
(Ready to power up)
Always be sure all power supplies for this system have
Memory No memory detected
the same power output. If mixed power supplies are
installed, the system will not operate.
Display memory Video adapter missing or with
read/write status faulty memory
For more information go to :
System System overheat
http://www.supermicro.com/support
http://www.supermicro.com
CPU Installation
Align CPU to socket;
install CPU straight down

!
NOTE:
Do not bend pin inside socket
Heatsink Installation
Screw #D
Screw #B
Screw #A
Screw #C
Caution
!
SAFETY INFORMATION
WARNING:
!
CAUTION:
MNL-xxxx- QRG