GE r08654v-1 Installation Instructions Manual page 9

Cutout for 30"
A
Ovens only
For JTP30, JTP70, PT916, PT920, ZET938 models only.
Allow 11/16"
(1.75 cm) for
ALLOW 11/16" FOR
overlap of oven
OVERLAP OF THE
over side edges
OVEN OVER SIDE
of cutout
EDGES OF CUTOUT
21"
(53.3 cm)
21"
Allow a minimum
ALLOW A MINIMUM
OF 21" FOR CLEARANCE
of 21" (53.3 cm) for
TO ADJACENT CORNERS,
clearance to adjacent
DRAWERS, WALLS ETC.
corners, drawers,
walls, etc. when
door is open
If the cabinet does not have a solid bottom,
two braces or runners must be installed
level with the bottom of the cutout to
support the weight of the oven. For single
ovens, the runners and braces must
support 150 lbs (68 Kg).
NOTE: If marks, blemishes or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered.
These ovens are not approved for
stackable installations.
Installation Instructions
Cutout
9 1/2" (24.1 cm)
Width
CUTOUT
28 1/2" (72.4 cm)
WIDTH
28 1/2" MIN.
Min.
28 5/8" MAX.
28 5/8" (72.7 cm)
Max.
Opening
Cutout
Between
Height
THE OPENING
Inside Walls
27 1/4"
BETWEEN INSIDE
Must Be CUTOUT
(69.2 cm) Min.
WALLS MUST
HEIGHT
At Least
27 5/16"
BE AT LEAST
27 1/4" MIN.
28 1/2"
28 1/2"WIDE
(69.4 cm) Max.
27 5/16" MAX.
(72.4 cm)
Wide
Recommended
RECOMMENDED
cutout location CUTOUT
Allow 1" (2.5 cm)
LOCATION
ALLOW 1" FOR
from floor 32 1/2"
minimum for
32 1/2"
OVERLAP
(82.6 cm)
overlap of oven
FROM THE
ON OVEN TOP
top and 1 1 ⁄
" FLOOR
AND BOTTOM
4
(3.2 cm) overlap
OF CUTOUT
of oven bottom
of cutout
CABINET
Cabinet
WIDTH
Width
30"
30" (76.2 cm)
Single Built-In
(76.2 cm)
Junction Box
Max.
5"
Location
(junction box
may be
located in
JUNCTION BOX
adjacent
LOCATION
cabinet)
22" (55.9 cm)
22" TO
BOTTOM OF Min. to
JUNCTION BOX
Bottom of
Junction Box
Suitable
Bracing
to Support
SUITABLE
Runners
BRACING
TO SUPPORT
RUNNERS
Side by Side Installations
Install two wall ovens in separate cutouts.
Allow 2" (5.1 cm) min. between cutouts.
Cutout –
Observe all
dimensions
and
requirements.
9
Cabinet Width 30" (76.2 cm)
Recommended
Cutout Location
from Floor 32 1/2" (82.6 cm)
Cutout Depth 23 1/2" (59.7 cm) Min.
Cutout Width 28 1/2" (72.4 cm) Min.
28 5/8" (72.7 cm) Max.
Cutout Height 27 1/4" (69.2 cm) Min.
27 5/16" (69.4 cm) Max.
NOTE: If the cabinet does
not have a front frame and the
sides are less than 3/4" (1.9 cm)
thick, shim both sides equally to
establish the cutout width.
C L
21 5/8"
21 5/8"
OVER CENTERLINE
(54.9 cm) Over
OF CABINET
Centerline
of Cabinet
2" (5.1 cm)
Cutout –
Min.
Observe all
dimensions
and
requirements.
2" x 4"
2" x 4" or
(5 cm x 10 cm)
EQUIVALENT
RUNNERS
or equivalent
runners level
with bottom
of cutout