Hitachi L700 SERIES Quick Reference Manual page 42

Chapter 3 Operation
(4) Procedure for directly specifying or selecting a code
- You can specify or select a code or data by entering each digit of the code or data instead of
scrolling codes or data in the monitor, function, or extended function mode.
- The following shows an example of the procedure for changing the monitor mode code "d001"
displayed to extended function code "A029":
1) Display the monitor mode code.
("d001" is displayed.)
RUN STOP/
RESET
(*2)
FUNC
(*3)
Press the
1
FUNC
together.
2) Change to the extended function mode.
RUN STOP/
RESET
FUNC
- Character "d" in the leftmost digit (fourth digit
from the right) starts blinking.
Press the
2
("A001" is displayed.)
(*3)
RUN STOP/
RESET
FUNC
- Character "A" is blinking.
- Pressing the [STR] key determines the
blinking character.
(*2)
STR
Press the
FUNC
(to determine character "A").
3) Change the third digit of the code.
RUN STOP/
RESET
FUNC
- Character "0" in the third digit is blinking.
- Since the third digit need not be changed,
press the [STR] key to determine the
character "0".
("A029" is displayed.)
(*2)
STR
- Character "9" in the first digit is blinking.
and keys
2
(*1)
5) Change the first digit of the code.
STR
- Character "1" in the first digit is blinking.
key twice.
(*2)
FUNC
(*2)
STR
- Character "2" in the second digit is
blinking.
key
4) Change the second digit of the code.
Press the
STR
key.
(Character "0" is
determined.)
STR
(*2)
FUNC
- Character "0" in the second digit is
blinking.
6) End the change of the extended function code.
Press the
key.
RUN STOP/
RESET
FUNC STR (Character "9"
is determined.)
1
Press the key eight
times or the key twice.
2
RUN STOP/
RESET
FUNC STR
Press the key.
STR
("A021" is displayed.)
RUN STOP/
RESET
FUNC STR
Press the key twice.
1
RUN STOP/
RESET
FUNC STR
3 - 10
STR
RUN STOP/
RESET
FUNC STR
- Selection of code "A029" is completed.
* If a code that is not defined in the code list
or not intended for display is entered, the
leftmost digit (fourth digit) (character "A"
in this example) will start blinking again.
In such a case, confirm the code to be
entered and enter it correctly. For further
information, refer to Section 4.2.84. "
Function code display restriction," (on
page 4-79), Section 4.2.85, "Initial-screen
selection," (on page 4-81), Section 4.2.86,
"Automatic user-parameter setting," (on
page 4-82), and Chapter 8, "List of Data
Settings."
7) Press the key to display the data
FUNC
corresponding to the function code,
change the data with the 1
key, and then press the
2
store the changed data. (*4)
Note that you can also use the procedure
(steps 1) to 6)) described here to change
the data. (*3)(*4)
*1
This procedure can also be used on
screens displaying a code other than
"d001".
*2
FUNC
If the key is pressed while a digit is
blinking, the display will revert to the
preceding status for entering the digit to
the right of the blinking digit.
*3
FUNC
If the key is pressed while the
leftmost (fourth) digit is blinking, the
characters having been entered to
change the code will be cancelled and the
display will revert to the original code
shown before the 1 and
were pressed in step 1).
*4
When changing data, be sure to press the
key first.
FUNC
and/or
key to
STR
2 keys