Mounting the Camera Housing Camera - Directional Adjustment LED Adjustments (EX36N only) 3.6.1 Power Adjustments Lens Replacement Camera Re-assembly Technical Information Troubleshooting - Camera Troubleshooting - LEDs General Specifications Bosch Security Systems, Inc. Instruction Manual F.01U.172.707 | 3.0 | 2011.02...
Page 5
Bosch Security Systems, Inc., will not be responsible for injuries or damages resulting from the improper installation or use of any camera sold by Bosch, its agents, distributors, or dealers. Bosch Security Systems, Inc.
Page 6
PSU box. – Contact a Bosch Service Center for further advice. F.01U.172.707 | 3.0 | 2011.02 Instruction Manual Bosch Security Systems, Inc.
Corner-mount No-grip Camera Safety | en Bosch Contact Information If this unit needs service, contact the nearest Bosch Security Systems Service Center for authorization to return and for shipping instructions. Repair Center Telephone: 800-566-2283 Fax: 800-366-1329 E-mail: repair@us.bosch.com Customer Service...
| Description Corner-mount No-grip Camera Description The EX36(N) Night Vision Camera has been designed with tilt on its faceplate to allow corner mounting and t provide better angle views in small rooms. The housing and faceplate consist of tough materials to withstand damage in hostile environments such as prison cells and psychiatric wards.
Corner-mount No-grip Camera Description | en 2.2.2 User-Supplied Parts The following items are required for installation but are not supplied: – mounting hardware – mounting tools Bosch Security Systems, Inc. Instruction Manual F.01U.172.707 | 3.0 | 2011.02...
Place the camera housing on a flat surface. Use the supplied hex key to remove the six screws holding the faceplate into the housing. Remove the square foam cushion attached to the camera lens. F.01U.172.707 | 3.0 | 2011.02 Instruction Manual Bosch Security Systems, Inc.
Page 11
Faceplate Housing Tamper-resistant hex screws Figure 3.2 below shows the interior layout of the EX36(N) camera assembly after the faceplate has been removed. Smaller details such as wiring and terminal blocks are omitted for clarity. Refer to the specific module sections for these details.
Refer to Figure 3.3 and Figure 3.4, Page 13, for wiring details. Figure 3.3 Electrically Isolated Board, Camera Voltage Regulator Board (VRB) Number Description Power IN Power OUT F.01U.172.707 | 3.0 | 2011.02 Instruction Manual Bosch Security Systems, Inc.
Follow all applicable building codes. Locate the unit so that it cannot be easily interfered with, either intentionally or accidentally. Bosch Security Systems, Inc. Instruction Manual F.01U.172.707 | 3.0 | 2011.02...
Page 14
Drill holes into the mounting surface. Depending on the type of mounting surface (brick, wood, etc.), you may need to pre-drill the holes for the mounting screws. Bosch recommends that you use the housing as a drill template-- refer to Figure 3.5 for the location of the mounting holes in the housing--to mark the location of the holes, and then drill the holes.
Number Description LED Array Tilt Adjustment Horizontal Adjustment Camera/Lens Assembly Adjustment screw Loosen both adjustment screws for tilt or horizontal directional alignment. Once optimal position is obtained, tighten the screws. Bosch Security Systems, Inc. Instruction Manual F.01U.172.707 | 3.0 | 2011.02...
– For photocell “On/Off” light-level adjustment, rotate VR2. Clockwise is off and counter-clockwise is on. – For IR power adjustment, rotate VR1. Clockwise is high and counter-clockwise is low. F.01U.172.707 | 3.0 | 2011.02 Instruction Manual Bosch Security Systems, Inc.
10. Adjust the camera sub-assembly mounting position so that when you mount the sub-assembly to the housing, the lens will not touch the window. 11. Close the front facia. Bosch Security Systems, Inc. Instruction Manual F.01U.172.707 | 3.0 | 2011.02...
Tighten screws carefully, but do not overtighten. Power up the camera and check its operation. Refer to Figure 3.8 below. Figure 3.8 Camera Re-assembly Number Description Photocell Foam pad F.01U.172.707 | 3.0 | 2011.02 Instruction Manual Bosch Security Systems, Inc.
If still no video, connect the camera directly to the monitor. Check the video signal. If okay, the problem is with the interconnections. If still no video, contact your Bosch Service Center. See Section 1.2 Bosch Contact Information for contact information.
850nm LEDs will have a faint red glow when “On”. 940nm LEDs are covert. Aim the LEDs directly at an IR-sensitive camera to see the lights or wait for the LEDs to warm up (two minutes). F.01U.172.707 | 3.0 | 2011.02 Instruction Manual Bosch Security Systems, Inc.
Steel, welded and powder coated Dimensions 8.3 in. (211 mm) W 6.0 in. (152 mm) D 5.5 in. (140 mm) H Weight 1.2 kg (2.64 lbs) Specifications are subject to change without notice. Bosch Security Systems, Inc. Instruction Manual F.01U.172.707 | 3.0 | 2011.02...
Page 22
| Technical Information Corner-mount No-grip Camera F.01U.172.707 | 3.0 | 2011.02 Instruction Manual Bosch Security Systems, Inc.