Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
Advertisement
Table of Contents
Related Manuals for Bosch EX14
Summary of Contents for Bosch EX14
- Page 1 INSTALLATION INSTRUCTIONS EX14/14N All Environment Camera MAN-14-04...
- Page 2 IMPORTANT SAFETY INSTRUCTIONS Read these instructions. Keep this instruction. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with manufacturer instructions. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
- Page 3 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the power where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
- Page 4 89/336/EEC Electromagnetic Compatibility Directive Only qualified personnel shall install any surveillance product. Bosch Security Systems, Inc. will not be responsible for injuries or damages resulting from the improper installation or use of any product sold by Bosch Security Systems, Inc their agents,...
- Page 5 PSU box. 3) Contact BOSCH Service Center for further advice.
-
Page 6: Table Of Contents
INDEX – EX14/14N Page Description...........1 Unpacking............2 Parts List............2 Items Required for Installation.....2 Initial Preparations ........3 Guidelines............3 Section 1. Camera Mounting .......4 Section 2. Camera I/O Connections ....9 Section 3. Input Power Connections………10 Section 4. Camera/LED Adjustments ..12 Section 5. Troubleshooting Guide .....15... -
Page 7: Description
DESCRIPTION The EX14 All Environment Camera consists of a two- piece injection molded watertight housing with a tough polycarbonate viewing window. This compact camera meets IP66 ratings for applications wherever environmentally sealed CCD cameras are required. The camera is especially suited for wash down applications in food processing and industrial clean-room installations. -
Page 8: Unpacking
Check the parts list and confirm all items have been located. Inspect the equipment thoroughly to ensure nothing was damaged in transit. Contact BOSCH Service Center if a problem is noted, see the rear page of this booklet for contact numbers. PARTS LIST (items supplied with unit) •... -
Page 9: Initial Preparations
Section 1: Camera Mounting • All cameras have been tested prior to shipment. GUIDELINES The installation of the EX14 Camera is shown in Sections 1 to 4 listed below. It is important that these steps are followed in sequence: 1. Camera Mounting 2. -
Page 10: Section 1. Camera Mounting
1. CAMERA MOUNTING Caution: Install the mounting bracket with the appropriate screws or drywall anchors to suit the mounting surface. Select a suitable location that is protected from accidental damage or tampering, and environmental conditions that could exceed the camera’s general specifications. See page 18. - Page 11 Power Input & Video Output Cable EX14 Camera Camera Angle Bracket Mounting Bracket Mounting Hardware Tighten this bolt after the camera viewing angle has been set FIGURE 1 – 1 Camera and Bracket – Mounting Details...
- Page 12 Warning: this apparatus must be securely attached to the wall or ceiling in accordance with installation instructions. Failure to follow installation instructions may results in injury/death Select a suitable location that protects the camera from accidental damage, tampering and environmental conditions exceeding the specifications of the camera to be mounted.
-
Page 13: Tools Required
Hardware required: • For wall mount: 10 x 2” Round Head Bolt, Qty = 2 ¼” Flat Washer, Qty = 2 Tools required: • Drill • Stud Finder • 5/32” Drill Bit • # 2 Screwdriver Mounting instructions for wall and ceiling mount: Camera is intended to be securely mounted to a wall using the mounting bracket supplied with the enclosure. - Page 14 • Marking the point on the wall in the center of the hole where mounting screw will be positioned. • Remove the wall mount bracket and using a 5/32” drill bit, drill a pilot hole at the marked point. • Align the ceiling/wall mount bracket mounting hole with the hole drilled in the ceiling/wall •...
-
Page 15: Section 2. Camera I/O Connections
2. CAMERA I/O CONNECTIONS Connect the Power Input (ac or dc) to the camera as shown below. Wires are not polarity dependent. Connect the Video Out BNC connector to a monitor. Video Out Power Input Figure 2 – 1 Camera I/O Connections... -
Page 16: Section 3. Input Power Connections
3. INPUT POWER CONNECTIONS The camera unit is pre-connected with an electrically isolated power board for 24Vac or 12V dc operation with no wiring change or wiring polarity. See Figure 3-1. Note: Input voltage is 12VDC to 24VDC for DC input. The AC input range is 12VAC to 24VAC. - Page 17 Power to Photocell LED Array Adjustment Enable Power Input FIGURE 3 – 2 LED Array Power Board...
-
Page 18: Section 4. Camera/Led Adjustments
4. CAMERA LED ARRAY ADJUSTMENTS Focus and Zoom Adjustments Loosen and tilt back the camera’s top cover to access the lens for adjustment. Step 3.1 - Loosen the lens setscrews for focus/zoom adjustments. See Figure 4-1 on page 13. ∞ The setscrew for N ←→... - Page 19 Loosen this set-screw for Focus Adjustment Loosen this set-screw for Telephoto or Wide Angle Adjustment FIGURE 4 – 1 Focus and Zoom Adjustments...
- Page 20 Use a Neutral Density filter or Infra-Red Pass filter to cover the lens during focusing to simulate low light conditions on scene for correct 24-hour focusing. For camera with vari- focal lens, the camera should be focused with the lens iris fully opened to simulate the worst possible depth of field.
-
Page 21: Section 5. Troubleshooting Guide
5. TROUBLESHOOTING GUIDE PROBLEM POSSIBLE LIKELY SOLUTION CAUSE No Video 1. Power Supply: -Connections…. Check input power connections at the cable leads. Check for loose wires. -Voltage Range... If connected to DC, check input voltage range of 12 – 24V. If connected to AC, check input voltage range of 12 –... - Page 22 If still no video, connect the camera directly to the monitor. Check the video signal. If okay, the problem is with the interconnections. If still no video, contact BOSCH Service Center. See rear page of this manual for contact information. ________________ ______________ ___________...
- Page 23 Poor Picture Snowy Image (cont’d.) Noisy Power Check connections. Supply Relocate or replace the power supply. Horizontal Scan Lines, Rolling Up or Down Ground Check the coax Looping on cable shield is not video cable touching ground, Negative, e.g. at couplings. scrambled, or Check video faded image...
-
Page 24: Section 6. General Specifications
6. GENERAL SPECIFICATIONS Power Consumption: EX14 2W(max.) Vdc and Vac EX14N 5.3W(max.) Vdc and Vac Input Voltage: 12 - 24 Vdc, 12 – 24Vac, isolated Enclosure (housing): ABS/Nylon (sealed to IP66) Viewing Window: Tempered Glass H: 3.35” (85mm) Dimensions: W: 3.35” (85mm) L: 7.10”... - Page 25 Notes:...
- Page 26 Notes:...
- Page 27 Notes:...
- Page 28 Phone: +65 6319 3450 Telephone+1 888-289-0096 Phone: + 31 40 2577 284 Fax: +65 6319 3499 +1 585-223-9180 Fax: +31 40 2577 330 apr.securitysystems@bosch.com Email: security.sales@us.bosch.com emea.securitysystems@bosch.com www.boschsecurity.com www.boschsecurity.us www.boschsecurity.com © Bosch Security Systems, Inc. 2009; Data subject to change without notice.