Related Manuals for Bosch EX7
Summary of Contents for Bosch EX7
- Page 1 INSTALLATION INSTRUCTIONS EX7/8 Ceiling / Wall Mount Camera MAN-7-8-05 IMPORTANT SAFETY INSTRUCTIONS...
- Page 2 Read these instructions. Keep this instruction. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with manufacturer instructions. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
- Page 3 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the power where they exit from the apparatus. 11. Only use attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
- Page 4 CSA Certified / UL Listed CLASS 2 power adaptors must be used in order to comply with electrical safety standards. Bosch Security Systems, Inc. will not be responsible for injuries or damages resulting from the improper installation or use of any product sold by Bosch Security Systems, Inc their agents, distributors or dealers.
- Page 5 PSU box. 3) Contact BOSCH Service Center for further advice. INDEX PAGE...
-
Page 6: Table Of Contents
Description……………………………………………..….1 Unpacking……………………………………………..…..2 Parts List…………………………………………………..2 Items Required for Installation…………………………..2 Initial Preparations………………………………………..3 Guidelines…………………………………………………3 Mechanical Specifications……………………………….4 SECTION 1. Camera Housing – Internal Modules, Locations and Access…………..5 2. Power Input Wiring Connections……………………6 3. Mounting – Camera Housing………………………..7 4. Camera Lens – Settings and Adjustments…………9 5. -
Page 7: Description
24V ac operation without any wiring changes. Its’ wider voltage range also provides protection from voltage surge, transient spikes, and reverse voltage. The difference between the EX7 and the EX8 is the EX7 Camera is a single sensor version and the EX8 is a dual sensors version. -
Page 8: Unpacking
Check the parts list and confirm all items have been located. Inspect the equipment thoroughly to ensure nothing was damaged in transit. Contact BOSCH Service Center if a problem is noted, see the rear page of this booklet for contact numbers. PARTS LIST (items supplied with unit) ... -
Page 9: Initial Preparations
GUIDELINES Four requirements must be met before the EX7/8 can be installed. The sections listed below will aid the installer in setting up the camera for these requirements. -
Page 10: Mechanical Specifications
MECHANICAL SPECIFICATIONS (See Section 8 - General Specifications, for more information) SIDE VIEW FRONT VIEW - 4 -... -
Page 11: Camera Housing - Internal Modules, Locations And Access
1. CAMERA HOUSING – INTERNAL MODULES, LOCATIONS and ACCESS Step 1.1 - Remove the four security screws holding the welded housing to the chassis assembly. Use the supplied Allen key. Step 1.2 - Carefully separate the housing from the chassis assembly, ensuring the wires are not displaced and the camera lens is not damaged. -
Page 12: Power Input Wiring Connections
2. INPUT POWER / VIDEO OUTPUT CONNECTIONS The camera unit is pre-connected with an electrically isolated power boards for 24VAC or 12VDC operation with no wiring change or wiring polarity. See Figure 2-1 for wiring details. Note: Input voltage is 10.5VDC to 40VDC for DC input. The AC input range is 12VAC to 28VAC. -
Page 13: Mounting - Camera Housing
3. MOUNTING – CAMERA HOUSING Caution: Ensure the selected location is protected from falling objects, accidental contact with moving objects, and unintentional interference from personnel. Follow all applicable building codes. The following installation guidelines must be followed: • Locate the camera such that it cannot be easily interfered with, either intentionally or accidentally. - Page 14 Step 3.1 Feed the camera’s power & video cables through the foam gasket at the bottom of the camera chassis. Step 3.2 Connect these cables to the power & video cables that have been routed from their remote location into the electrical box. Step 3.3 Mount the camera housing to the electrical box and ceiling as shown in Figure 3-1 below.
-
Page 15: Camera Lens - Settings And Adjustments
4. CAMERA LENS – SETTINGS and ADJUSTMENTS For optimum picture quality, the lens should be as close as possible to the inside face of the viewing window, without touching. For unique designation wall mount, rotate the camera to desire location. Power should be applied when performing the following adjustments. - Page 16 4.2 Vari Focal and “Auto-Iris” Control Adjustments Step 4.2.1 - Loosen the lens set screws for focus/zoom adjustments. See Figure 4-2 Step 4.2.2 - The set screw marked N ←→ ∞ is used for image focus. Step 4.2.3 - The set screw marked T←→ W is used for telephoto or wide-angle settings.
- Page 17 FIGURE 4 – 3 Adjustments, AI Control Table A – Brightness Level Adjustment Brightness LEVEL Adjustment Turn towards “H” For a brighter picture Turn towards “L” For a darker picture - 11 -...
- Page 18 Use a Neutral Density filter or Infra-Red Pass filter to cover the lens during focusing to simulate low light conditions on scene for correct 24-hour focusing. For camera with vari- focal lens, the camera should be focused with the lens iris fully opened to simulate the worst possible depth of field.
-
Page 19: Camera Re-Assembly
5. CAMERA RE-ASSEMBLY Make sure all wires are properly connected and tightened into the terminal blocks, all holes are sealed against moisture penetration, and all mounting screws are tight. Step 5.1 - Gently press the camera housing in place. Ensure the lens is not touching the inside of the viewing window. -
Page 20: Troubleshooting Guide
Check BNC connector. If still no video, connect the camera directly to the monitor. Check the video signal. If okay, the problem is with the interconnections. If still no video, contact BOSCH Service Center. See rear page - 14 -... -
Page 21: Picture Quality
of this manual for contact information. Poor Picture Quality Dim Image Iris closed Increase iris level on lens Snowy Poor Video Ensure the video cable is Image Signal correctly matched and terminated with 75 ohms at each end. Make sure the video cables are of similar types. -
Page 22: Mounting Hole Template
7. Mounting Hole - Diagram - 16 -... -
Page 23: General Specifications
GENERAL SPECIFICATIONS Input Voltage: 12V dc or 24V ac (60Hz), 3.6W Temperature Range: C -- 60 C (-58 F --140 Enclosure (housing): Electrolytic Steel Plate Viewing Window: Polycarbonate 82.6 mm H ( 3.25” ) Dimensions: 117.5 mm W ( 4.625” ) 273.1 mm L ( 10.75”... - Page 24 Phone: +65 6319 3450 Telephone+1 888-289-0096 Phone: + 31 40 2577 284 Fax: +65 6319 3499 +1 585-223-9180 Fax: +31 40 2577 330 apr.securitysystems@bosch.com Email: security.sales@us.bosch.com emea.securitysystems@bosch.com www.boschsecurity.com www.boschsecurity.us www.boschsecurity.com © Bosch Security Systems, Inc. 2009; Data subject to change without notice.