Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for K2 Mounts K2-F-Series
Summary of Contents for K2 Mounts K2-F-Series
-
Page 2: Table Of Contents
Table of Contents Before You Begin ..............2 Package Contents . -
Page 3: Before You Begin
Verify that you have received all of the parts listed below: Mounting Plate(Attach to wall) All models have 1 unit K3-F-SERIES & K3-T-SERIES K2-F-SERIES & K2-T-SERIES Left and Right Scr een Mounting Brackets Mounting Plate Hardware (To secure Mounting Plate to Wall) -
Page 4: Update Kit
UPDATE Selecting Screen Mounting Bracket Hardware These instructions should be used when attaching the Screen Mounting Brackets to your Stop: If screws are included in your TV’s four rear mounting holes, use those screws to attach the Screen Mounting Brackets. You will not need the hardware included in this kit. - Page 5 Find Screen Bracket Screws Find the screws from this hardware kit that best fit your TV. Note that there are screws with four different diameters: M4, M5, M6, and M8. Determine which of these thread diameters should be used by gently threading one ew into a rear mounting hole , until you find the appropriate size.
-
Page 6: What You Will Need
What You Will Need You will need these tools to install y our wall mount bracket: Measuring Tape Level Stud Finder (f or w ood stud wall installation) Pencil or Pen Electric Drill 1/8” Drill Bit (f or w ood stud wall installation) 1/2”... -
Page 7: Installation
Installation Installing y our Flat Panel Wall Mount bracket involves the following steps: 1. Determine the Wall Mounting Location 2. Attach the Mounting Plate to the Wall 3. Attach the Mounting Brack ets to the TV 4. Hang the TV on the Mounting Plate 5. -
Page 8: Attach The Mounting Plate To A Wood Stud Wall
Locate different studs that run continuously from floor to ceiling W ood Studs The K2-F-SERIES and K2-T-SERIES require the wall studs to be 16 inches apart (16 inches on center). These brackets cannot be used if the wall studs are spaced farther apart. - Page 9 (B) Determine Mounting Hole Locations Using the level and measuring ta pe, make a mark 3-1/8” directly above and 3-1/8” directl y below the Mounted TV Center P oint. These marks are the Upper and Lower Center P oints. Using the le vel, draw a horizontal (side-to-side) line through the Upper Center Point that connects all stud centerlines.
-
Page 10: Attach The Mounting Plate To A Concrete Or Concrete Block Wall
Using the level and measuring ta pe, make a mark 3-1/8” dir ectly above and 3-1/8” directly belo w the Mounted TV Center Point. These marks are the Upper and Lower Center Points. K2-F-SERIES, K2-T-SERIES, K3-F-SERIES, K3-T-SERIES Hold the Mounting Plate against the wall, aligning the center of the Mounting Plate with the Mounted TV Center P oint. - Page 11 (C) Anchor Mounting Plate to Wall Hold the Mounting Plate against the wall, aligning the marked Mounting Plate slots with the Concrete Anchors in the wall. Using the ratchet and 7/16” socket, attach the Mounting Plate into the anchors with the four 1/4” x 2-1/2”...
-
Page 12: Attach The Screen Mounting Brackets To The Tv
Be sure the top edges of both brackets are the same distance fr om the top of the TV. K2-F-SERIES and K3-F-SERIES Place the flat surface of the Left and Right Screen Mounting Brack ets on the back of the TV, lining up one hole in each brack et with a TV mounting hole . - Page 13 K2-T-SERIES and K3-T-SERIES Place the flat surface of the Left and Right Screen Mounting Brack ets on the back of the TV, lining up one hole in each brack et with a TV mounting hole. Center Be sure to use the same hole on both Scr een Line Left Mounting Brack ets, so that the top of each...
-
Page 14: Hang The Tv On The Mounting Plate
Hang the TV on the Mounting Plate Using two or more people, pick up the TV and tilt the top edge to ward the wall at the top of the Mounting Plate. Move down the TV until the upper (longer) hooks engage the top of the Mounting Plate, then rotate the bottom of the TV until the lower (shorter) hooks are beneath the Mounting Plate. -
Page 15: Adjust The Screen Angle (K2-T-Series And K3-T-Series)
Adjust the Screen Angle (K2-T-SERIES and K3-T-SERIES) You can adjust the screen angle using the knobs located on the outside edge of each Screen Mounting Bracket. Loosen the knobs on both Screen Mounting Brackets by turning each knob counter-clockwise one full turn. Adjust the TV to the desired angle. - Page 16 Use with products heavier than the maximum weights indicated may result in instability and possibly cause injury. Specification Maximum Model Weight Tilt Range Load Weight K2-F-SERIES approx.8.42 lbs 100 lbs K2-T-SERIES approx. 12.16 lbs 15 degrees up/down 100 lbs K3-F-SERIES approx.
-
Page 17: K2 Mounts Warranty
K2 Mounts Warranty K2 Mounts warrants to the original purchaser of its mounting brackets for the life of the bracket, that the bracket shall be free from defects in assembly, material, or workmanship and will repair or replace, at its sole discretion, a defective bracket free of charge, provided the bracket is returned to K2 Mounts prepaid by purchaser. - Page 18 an K2 Mounts product failure, and does not protect against acts of God such as flood, earthquake, war, vandalism, theft, normal-use wear and tear, corrosion or abuse . Any damage caused by failure to observe instructions for installation, or product limitations specifed in the product manual or product specification sheet or mounting on unsuitable surfaces will not be covered by the K2 Mounts warranty.
- Page 19 K2 Mounts is a Product of TV Mounting Brackets, Inc. www.k2mounts.com Rev00...