Related Manuals for K2 Mounts K2-A3-S
Summary of Contents for K2 Mounts K2-A3-S
- Page 1 QUALITY MOUNTING SOLUTIONS STEP-BY-STEP INSTALLATION MANUAL K2-A3-S ARTICULATING MOUNT k2mounts.com...
-
Page 2: Before You Begin
K2-A3-S Installation Instructions & Manual Table of Contents Before You Begin What You Will Need Package Contents Installation Wood Stud Wall Installation Concrete or Concrete Block Wall Installation Specifications K2Mounts Warranty Before You Begin Read this entire manual! Do not attempt to install this product if you do not understand the instructions or if there are missing or defective parts. If you are in doubt, contact a STOP qualified contractor to install the mounting bracket. -
Page 3: Package Contents
Package Contents Verify that you have received all of the parts listed below: Articulating Arm/Wall Mounting Plate Screen Plate Wall Hardware Screen Hardware 6 - 3” X 7/6” lag bolts Hex wrench 6 - 3/4” washers 6 - 3/8” x /2” black spacer 6 - 3/8” x 3/4” black spacer 6 - 3/4” washers 6 - 7/6” washers 6 - M6 x 30mm screws 6 - M6 x 5mm screws 6 - M5 x 30mm screws 6 - M5 x 5mm screws 6 - M4 x 30mm screws 6 - M4 x 2mm screws If any parts are missing or damaged, contact K2Mounts at support@k2mounts.com for a replacement. -
Page 4: Wood Stud Wall Installation
Installation To mount to a wood stud wall, continue below. To mount to a concrete wall, go to page 4. Wood Stud Wall Installation Locate the Wall Studs Wall studs run vertically (up and down) inside the wall, behind the drywall or plaster. You must attach the mounting plate to two separate wall studs that run from floor to ceiling. - Page 5 Concrete or Concrete Block Wall Installation Warning: Attaching the wall mount to a brick wall could result in property damage or personal injury. Obtain Concrete Anchors The hardware needed to mount to a concrete wall is not included. Purchase at least 5 concrete anchors with a weight rating that will accomodate your screen plus the weight of the mounting bracket (about 16 lbs.). Install Anchors . If you have the installation poster: a. Tape the poster to the wall with the ACTUAL SIZE TEMPLATE side showing.
- Page 6 Attach the Screen Plate to the Screen . Line up the holes in the Screen Plate with the holes on the back of the screen. 2. If the screws that came with your screen hold the plate securely, use them, otherwise use screws from those provided in the Screen Hardware bag. 3. Attach the Screen Plate with a washer and then a screw in each hole. Attach the Screen Plate to the Arm 1.
-
Page 7: Specifications
Specifications Caution: This mounting bracket is intended for use only with the maximum load weight indicated. Use with products heavier than the maximum weight indicated may result in instability and possibly cause injury. Bracket Weight: 5.4 lbs Tilt Range: 5 degrees up, 14 degrees down Maximum Load Weight: 0 lbs VESA Monitor sizes: 75 x 75, 100 x 100, 200 x 200... -
Page 8: K2Mounts Warranty
K2Mounts Warranty K2Mounts warrants to the original purchaser of its mounting brackets for the life of the bracket, that the bracket shall be free from defects in assembly, material, or workmanship and will repair or replace, at its sole discretion, a defective bracket free of charge, provided the bracket is returned to K2Mounts prepaid by purchaser. Unauthorized service or repairs by anyone other than K2Mounts or a pre-approved repair facility renders this warranty void and shall release K2Mounts from any further responsibility or obligation. - Page 9 * Failure to perform in accordance with that bracket’s specifications sheet or product manual ** Properly installed in accordance with that bracket’s installation instruction sheet or bracket manual and only when mounted on approved surfaces. K2 Mounts is a Product of TV Mounting Brackets, Inc. © 2006 K2Mounts. All rights reserved. www.k2mounts.com...
- Page 10 Copyright 2006 K2Mounts. All rights reserved. k2mounts.com...