Assembly - Healthrider 275p Treadmill User Manual

ASSEMBLY

Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Assembly requires your own Phillips screw-
driver and rubber mallet
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
1. With the help of a second person, carefully raise the
treadmill to the position shown at the right.
Whilst a second person tips the treadmill to one side
slightly and holds it, insert one of the Extension Legs (103)
into the treadmill as shown. Make sure that the Extension
Leg is turned so the Thick Base Pad (11) is on the bottom.
Next, tip the treadmill to the other side and insert the
other Extension Leg (not shown) in the same way. Lower
the side of the treadmill so that both Extension Legs
(103) are resting flat on the floor.
2. With the help of a second person, carefully lower the
treadmill frame and then tip the Uprights (82) down as
shown. Make sure that the Extension Legs (103) re-
main in the Uprights.
Attach each Extension Leg (103) with two Screws (101)
and a Base Pad (97) as shown.
Note: One replacement Base Pad (97) and Spacer (not
shown) may be included. If a Base Pad becomes worn
and needs to be replaced, use the replacement Base
Pad. If a Thick Base Pad (11) needs to be replaced, use
the replacement Base Pad with the Spacer.
3. With the help of a second person, carefully tip the
Uprights (82) back to the vertical position.
Attach the Latch Assembly (13) to the left Upright (82)
with two Latch Screws (89).
.
1
103
11
2
11
97
82
101
103
11
3
13
89
89
82
6
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet. (See HOW TO PLUG IN
b. Make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the treadmill
d. Check the on/off switch located on the treadmill
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the
b. Make sure that the power cord is plugged in.
97
c. Remove the key from the console. Reinsert the key fully into the console.
101
d. Make sure that the on/off switch is in the on position.
103
e. If the treadmill still will not run, please call our Customer Service Department.
11
PROBLEM: The speed display on the console does not function properly
101 SOLUTION: a. Remove the key from the console and UNPLUG THE
THE POWER CORD on page 9.) If an extension cord is needed, use only a 3-conductor, 1 mm
(14-gauge) cord that is no longer than 1.5 m (5 ft.). Important: The treadmill is not compatible with
GFCI-equipped outlets.
near the power cord. If the switch protrudes as
shown, the circuit breaker has tripped. To reset the
circuit breaker, wait for five minutes and then press
the switch back in.
near the power cord. The switch must be in the on
position.
circuit breaker has tripped, wait for five minutes and then press the switch back in.
POWER CORD. Remove the screws from the hood
and carefully remove the hood. Locate the Reed Switch
(21) and the Magnet (43) on the left side of the Pulley
(42). Turn the Pulley until the Magnet is aligned with
the Reed Switch. Make sure that the gap between
the Magnet and the Reed Switch is about 3 mm (1/8
in.). If necessary, loosen the Short Screw (76) and
move the Reed Switch slightly. Retighten the Screw.
Re-attach the hood, and run the treadmill for a few min-
utes to check for a correct speed reading.
23
2
c
Tripped Reset
Tripped Reset
d
On
Position
a
3 mm
42
76
43
21
Top
View