Table of Contents
Advertisement
Installation
Instructions
ISTEP151
CONNECT POWER
SUPPLY
Skip this step if equipped
with
power
cord
Verify
that power
is turned
off at the source,
(If a power
cord
with
plug
is used,
proceed
t(> Step
16.)
• Removejui1ctioi_
box
cover.
• Secure
house
wiring
to the
back
of the junction
box
with
a strain
relief.
• Locate
the
three
dishwasher
wires,
(white,
black
and
green)
with
stripped
ends.
Insert
dishwasher
wires
through
the
small
hole
in thejm_ction
box.
Use wire
nuts
to com_ect
inc()ming
gro/md
to green,
white
to
white
and
black
to black.
• Replace
junction
box
cover.
Check
to be sure
that
wires
are
not
pinched
m_der
the
cover.
A
C
Remove
Insert Power
Junction Box
Cord Wires Thr
Cover
Strain Relief
__
and Tighten
White
Groundd __
Black
B Check That White, Black and -4 _',-'_"
J
Green Dishwasher Wires Are Threaded
Thru Small Hole in Bracket
[}
Use ULListed
Figure AA
Wire Nuts
[STEP 16] PRE-TEST CHECK LIST
Review
this list after
installing
your dishwasher
to
avoid
charges
for a service
call that is not covered
by
your warranty,
[] Check
to be sm'e
power
is OFK
[] Open
door
and
remove
all fi)am
and
paper
packaging.
[] Locate
the
Owner's
Mamlal
in the
literature
package.
[] Read
tile
Owner's
Manual
fin" operating
in structions.
[] Check
door
opening
and
closing.
If door
does
not
open
and
close
fl'eelv
or tends
to thll,
check
spring
cable
routing.
See
Step
1.
[] Check
to be sm'e
that
wiring
is secm'e
trader
tile
dishwasher,
not
pinched
or in contact
with
door
springs
or other
components.
See
Step
10.
[] Check
door
aligmi_ent
with
tub.
If door
hits
tub,
level
dishwasher.
See Step
11.
[] Pull
lower
rack
out,
about
halfway.
Check
to be
sm'e
it does
not
roll
back
or flwward
on the
door.
If
the
rack
moves,
at!just
leveling
legs.
See
Step
11.
[] Check
door
alignment
with
cabinet.
If door
hits
cabinet,
reposition
dishwasher.
See Step
12.
[] (;heck
that
door
spring
does
not
contact
water
line,
fill hose,
wiring
or other
compoi_ents.
See
Step
13.
[] Verif}'
water
supply
and
drain
lines
are
not
kinked
or" in contact
with
other
components.
Contact
with
motor
or dishwasher
fl'ame
could
cause
noise.
[] Turn
on tile
sink
hot
water
t.mcet
and
verif}' water
temperatm'e.
Incoming
water
temperature
must
be
between
] 20°F
and
150°F.
] 20°F
rain.
temperature
is required
fin" best
wash
perflwmance.
See
"Pre-
pare
Hot
Water
Line,"
page
4.
[] Add
2 quarts
of water
to the bottom
of the
dishwasher
to lubricate
the
pmnp
seal.
[] Turn
on water
supply.
Check
for leaks.
Tighten
cmmections
if needed.
[] Remove
protective
film
if present
from
tile
control
panel
and
door.
10
Advertisement
Table of Contents
