Table of Contents
Advertisement
Installation
Instructions
ISTEP151
CONNECT POWER
SUPPLY
Skip this step if equipped
with
power
cord
Verify
that power
is turned
off at the source,
(If a power
ford
with
phlg
is used,
proceed
t(> Step
16.)
• Relllove.jtlnctioi_
box
covei'.
• Secure
house
wiring
to the
back
of thejulacti(m
box
with
a strain
relief.
• Locate
the
three
dishwasher
wires,
(white,
black
and
green)
with
stripped
ends.
Insert
dishwasher
wires
through
the
small
hole
in thejuiaction
box.
Use wire
nuts
t() coimect
iiac()ming
ground
to green,
white
t()
white
and
black
t() black.
• Replace
junction
box
covei'.
Check
to be S/li'e that
wires
are
not
pinched
under
the
cover.
A
C
Remove
Insert Power
Junction Box
Cord Wires Thr
Cover
Strain Relief
__
and Tighten
White
Gr°und_d_ _
,//Black
B Check That White, Black and -_
J
Green Dishwasher Wires Are Threaded
Thru Small Hole in Bracket
[}
Use UL Listed
FigureAA
Wire Nuts
[STEP 16] PRE-TEST CHECK LIST
Review
this list after
installing
your dishwasher
to
avoid
charges
for a service
call that
is not covered
by
your warranty,
[] Check
to be sure power
is OFK
[] Open
door and
remove
all flmm and
paper
packaging.
[] Locate
tile Owner's
Manual
in tile literature
package.
[] Read
tile Owner's
Manual
fin" operating
in structions.
[] Check
door opei_ing
and closing.
If door does not
open
and close fl'eelv or tends
to tall, check
spring
cable routing.
See Step 1.
[] Check
to be sure that wiring
is secure
under
tile
dishwasher,
not pinched
or in c/intact
with door
springs
or other
components.
See Step
10.
[] Check
door aligmnent
with till). If door hits till),
level dishwasher.
See Step
11.
[] Pull lower
rack out, about
halfway.
Check
to be
sure it does not roll back or fl)rward
on the door.
If
the rack moves,
at!just leveling
legs. See Step 11.
[] Check
door aligmn
ent with cabinet.
If door
hits
cabinet,
reposition
dishwasher.
See Step
12.
[] Check
that door spring
does not contact
water line,
fill hose, wiring
or other
colnpoi1ents.
See Step 13.
[] Verify' water
supply
and
drain
lines are not kinked
or in contact
with other
compoi_ents.
Contact
with
motor
or dishwasher
fl'ame
could
cause noise.
[] Turn
on tile
sink
hot
water
t, ulcet
and
verify' water
temperature,
h_coming
water
temperature
must
be
between
120°F
and
150°F.
120°F
rain.
temperature
is req uired
fk)r best
wash
perfk_rmance.
See
"Pre-
pare
Hot
Water
Line,"
page
4.
[] Add
2 quarts
of water
to tile bottom
of tile
dishwasher
to hlbricate
the
pump
seal.
[] Turn
on water
supply.
Check
fin" leaks.
Tighten
coimections
if needed.
[] Remove
protective
fihn if present
from
tile control
panel
and door.
10
Advertisement
Table of Contents
