Kitchenaid architect series ii kbls19ktms: user guide (41 pages)
Summary of Contents for KitchenAid 4KSRF42DT
Model 4KSRF42DT IMPORTANT: Installer: Leave tnstallation lnstr~~ctions with the Homeowner. Hommwr@r: Keep Installation Instructions for future reference. Save Installation Instructions for local electrical inspector’s use. Part No. 1113438 * Registered Trademark of KitchenAid, Inc., U.S.A., KitchenAid Canada, Inc., Licensee in Canada...
Three colors of acrylic door panel Location of the built-in refrigerator kits are available from your must permit the doors to open to KitchenAid dealer: White, Black at least 90°. and Almond. Each kit includes door Because of the weight and size of...
Dimensions for built-in area Electrical outlet should be centered wlthln shaded area. (178 ml electrical &ouhded let location Width and depth of the built-in area Wall are determined by the type of plumbing installation. The built-in refrigerator location can be installed with the doors flush with the wall, with the doors protruding from the wall, or with side panels enclosing refrigerator.
The 8-l/2” (216 mm) top grille is when the maxlmum provided. Smaller top grilles must extenslon of levelers l-114” (32 mm be ordered from your KitchenAid elow rollers] 1 s dealer. Check the chart below for used to remove the wefght from...
Custom door panels, handle Inserts and top grille panels Panel routlng for door Refrigerator door panel and top grille panels. Door and top grille panels: 22-314” Dimensions shown are with routed 114” mm) 4 (578 edges. Routing is required if panels are more than l/4”...
Side panel requirements mm) tolerance l/8” (3 -(lo67 mm)-b 114" -II- S/32" (4mm) 23-118” (587 mm) depth protruding door lnrtalfatlon 1116" 23-716" 3-314" (606 mm) depth (95 mm) flush door lnstallatlon ;:L, 5132" side trim (4mm) Side trim Refrlgerator when 25” (635 mm) depth is One method is to attach side available.
Electrical Water supply Ground electric drill or use a hand drill. Drill a 3/16” (5 mm) hole in requirements requirements vertical cold water line. Attach a saddle valve to the water line with Use only 114” (6 mm) copper a clamp in an easily accessible tublng for water Ilne.
Product support wood , block(a) A solid soffit or a wood block is required to prevent the refrigerator l\\\\\lj/fl Block(s) ml’*t from tipping forward after it is be lorig.enough installed. to fully cover wldth of cover. Determine what height the refrigerator will be when it is installed to fit opening.
Move refrigerator to Now start... kitchen. Place cardboard under DlwOOd Remove top grille assembly Personal injury Hazard refrfgerator: Aemove appliance package, literature package Because of the weight and dolly. Open doors and remove all and parts bag taped to the size of the bulkin boxes, parts packages and packing refrfgerator door and save.
side/ trim Remove tape from rear . leveling rods. Turn the two Move refrigerator close to leveling rods clockwise using a 516” final position. Remove (8 mm) socket and ratchet until the cardboard or plywood from cabinet weight is supported by the under refrigerator.
(Consult your builder to adjust countertops.) your KitchenAid’ and Care Guide. Keep Ins talla tion Ins true tions Check the water Check that connections at the...
Use and Care Guide. unsatisfactory, contact the Customer Relations Department, KitchenAid Canada, Inc., 1901 Minnesota Court Mississauga (Ontario) L5N 3A7 Telephone: (416) 821-6606 Prepared by KitchenAid Canada, Inc. Part No. 1113438 Printed in U.S.A. Mississauga, Ontario L5N 3A7 0 1989 KitchenAid Canada, Inc.