Table of Contents
Advertisement
INSTALLATION, MAINTENANCE AND USE
INSTRUCTIONS FOR
FREE-STANDING COOKERS
cm (type M91/M91V)
90x60
Model X906MFE* , X906 DUAL*,
X906GEV*
READ THE INSTRUCTION BOOKLET BEFORE INSTALLING AND USING
THE APPLIANCE.
The manufacturer will not be responsible for any damage to property or to persons
caused by incorrect installation or improper use of the appliance.
The manufacturer is not responsible for any inaccuracies, due to printing or transcription
errors, contained in this booklet. In addition, the appearance of the figures reported is also
purely indicative.
The manufacturer reserves the right to make changes to its products when considered
necessary and useful, without affecting the essential safety and operating characteristics.
Advertisement
Table of Contents
Related Manuals for Bertazzoni X906 DUAL
Summary of Contents for Bertazzoni X906 DUAL
- Page 1 INSTALLATION, MAINTENANCE AND USE INSTRUCTIONS FOR FREE-STANDING COOKERS cm (type M91/M91V) 90x60 Model X906MFE* , X906 DUAL*, X906GEV* READ THE INSTRUCTION BOOKLET BEFORE INSTALLING AND USING THE APPLIANCE. The manufacturer will not be responsible for any damage to property or to persons caused by incorrect installation or improper use of the appliance.
-
Page 2: Table Of Contents
CONTENTS: INSTALLER TECHNICAL MANUAL ....................... pg. 2 Installing the cooker - Installation information ....................pg. 2 Ventilation and aeration of rooms ........................pg. 3 Backguard installation instruction ........................pg. 3 Gas connection ............................... pg. 3 Adaptation to different types of Gas and burner adjustments................pg. 4 Electric connection ............................ -
Page 3: Ventilation And Aeration Of Rooms
MPORTANT INFORMATION FOR INSTALLING THE APPLIANCE The cooker can be installed separately, as a freestanding unit, on a plinth (Not suitable for X90 6 GEV* and X90 6 DUAL* models), or between kitchen units or between a kitchen unit and the wall. If installing the appliance as a freestanding cooker, screw the height adjustable telescopic legs supplied to the base of the appliance. -
Page 4: Adaptation To Different Types Of Gas And Burner Adjustments
When making the connection, take care not to apply excessive stress by counterbalancing tightening force. Ensure that the available gas supply is the same as the gas type label affixed near the gas connection point. If not, contact Bertazzoni for a Gas Conversion Kit. Natural Gas The natural gas regulator supplied must be fitted for natural gas. -
Page 5: Electric Connection
WARNING: After completing the above-mentioned replacements, the technician must adjust the burners, as described in the paragraph below, seal any adjustment and pre-adjustment devices and apply the label on the appliance, to replace the existing one, corresponding to the new gas adjustment. This label is contained in the spare nozzle bag. -
Page 6: Appliance Maintenance - Replacing Parts
When satisfied with the appliance, please instruct the user on the correct method of operation. In case the appliance fails to operate correctly after all checks have been carried out, please call the Bertazzoni Service Centre. APPLIANCE MAINTENANCE... -
Page 7: Description Of Control Panel And Control Types
To replace the power cable, lift the terminal board’s cover and replace the cable. To access the terminal board in cookers with a 3x2.5mm² cable, the back panel on the rear of the appliance must be removed. USE AND MAINTENANCE MANUAL WARNING: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. -
Page 8: Using The Gas Oven
Note: It is recommended not to try to ignite a burner if the relative flame cap is not in the correct position. If the flame does not light after the first attempt, wait 5 minutes for the gas to dissipate before attempting to re-light the burner. -
Page 9: Using The Electric Thermostat
then release the knob. Make sure that the burner remains on, otherwise repeat the operation. As for cookers without ignition trough knob, press the thermostat knob and the key with the spark symbol, wait about 10 seconds after the burner has been completely lit and then release the knob. Make sure that the burner remains on, otherwise repeat the operation. -
Page 10: Using The 9+0 Switch
- the symbol indicates that the electric fan, and the oven light have been turned on . - the symbol indicates that only the oven light is turned on; USING THE 5 + 0 SWITCH ( only cooker with Dual Enrgy oven) Dual Energy The 5 + 0 switch installed in the oven models is used, along with the electric or gas thermostat. -
Page 11: Using The Natural Conventional Electric Oven
- the symbol indicates that only the top external element (1200W) has been turned on; - the symbol indicates the only the bottom element (1800W) has been turned on; - the symbol indicates that only the grill element (1800W) has been turned on; - the symbol indicates that the top external element (1200W) and the grill element (1800W) have been turned on;... -
Page 12: Positioning The Oven Trays & Shelves
Before cooking, allow the oven to reach the desired temperature setting waiting for the orange light to turn off. This type of oven is equipped with a circular element around which a fan has been installed that creates forced-air circulation in the horizontal direction. -
Page 13: Using The Self Cleaning Oven
• Burners not igniting properly. • Gas valves, which are difficult to turn. In case the appliance fails to operate correctly, contact Bertazzoni. CLEANING THE APPLIANCE Before cleaning the appliance, it should be disconnected from the power supply and turn off the main gas feeder valve. - Page 14 Any subsequent necessary repairs or adjustments must be carried out with the greatest care and attention by authorised personnel. For this reason, we strongly advise you contact the Bertazzoni Service Center, specifying the nature of the problem, the model of the equipment and the serial number.
- Page 15 Fig. 1 Fig. 3 Fig. 4 Fig. 5 Fig.6 Fig.7...
- Page 16 Fig.8 Fig.9 Fig.10 Fig.11 Fig 12 Fig 13 Fig. 14...
- Page 17 Fig. 16 Fig. 17 Fig. 18 Fig. 19 Fig. 20 Fig. 21 Fig. 22 Fig. 23 Fig. 24 Fig. 25...
- Page 18 Fig. 26 Fig. 27 Fig.28a Fig.28b Fig.28c Fig.28d...
- Page 19 Fig. 29 Fig. 30 Fig. 31 Fig. 32...
- Page 20 OVERALL DIMENSIONS Cod. 310686...
Need help?
Do you have a question about the X906 DUAL and is the answer not in the manual?
Questions and answers