Summary of Contents for DeLonghi Electric Range DEGLSC 24 SS
Page 1
ELECTRIC RANGE for residential use only DEGLSC 24 SS Model: • INSTALLATION INSTRUCTIONS IMPORTANT - PLEASE READ AND FOLLOW IMPORTANT - PLEASE READ AND FOLLOW Before beginning, please read these instructions completely and carefully. Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.
WARNING • ALL RANGES CAN TIP • INJURY TO PERSON COULD RESULT • INSTALL ANTI-TIP DEVICE PACKED WITH RANGE • SEE INSTALLATION INSTRUCTIONS This appliance is designed and manufactured solely for the cooking of domestic (household) food and in not suitable for any none domestic application and therefore should not be used in a commercial environmement.
INSTALLATION INSTRUCTIONS WARNING! THIS APPLIANCE HAS TO BE INSTALLED BY A QUALIFIED INSTALLER. Installation must conform with local codes. Improper installation, adjustment, alteration, services, or maintenance can cause injury or property damage. Consult a qualified installer or a service agent. IMPORTANT: The use of suitable protective clothing/gloves is recommended when handling, installing of this appliance.
GENERAL INFORMATION WARNING!! WARNING!! ELECTRICAL GROUNDING INSTRUCTIONS The range must be electrically grounded in accordance with local codes or, in the absence of local codes, with the 1. This appliance shall not be used for space heating. This National Electrical Code, ANSI/NFPA No. 70-latest edition. information is based on safety considerations.
installation PROXIMITY TO SIDE CABINETS 1. This range may be installed directly adjacent to existing 36" (914 mm) high base cabinets. Range dimensions: • width: 23” 7/8 (606.5 mm) • depth: 24” 11/64 (614.1 mm) • height (without backguard): MIN 35” 17/32 (902.5 mm) - MAX 36” 7/32 (920 mm) •...
PROXIMITY TO SIDE CABINETS 1 3 " m a x . (3 3 0 m m ) Fig. 1.3 Fig. 1.4 ASSEMBLING THE BACKGUARD It is mandatory to install the backguard Assemble the backguard as shown in figure 1.5: • Screw the 2 screws “A” interposing the spacers. •...
LEVELLING THE RANGE The range is equipped with 4 LEVELLING FEET (supplied in a separate kit) and may be levelled by screwing or unscrewing the feet (fig. 1.8). It is important to observe the directions of figures 1.6, 1.7a, 1.7b. Fig.
electrical connection ELECTRICAL REQUIREMENTS WARNING • This appliance must be properly installed and grounded by a qualified technician in accordance with the National Electrical Code ANSI/NFPA No.70 (latest edition) and TO AVOID ELECTRICAL SHOCK HAZARD, BEFORE INSTALLING THE local electrical code requirements. IN CANADA: Electrical installation must be in APPLIANCE, SWITCH POWER OFF AT accordance with the current CSA C22.1 Canadian Electrical Codes Part1 and/or local THE SERVICE PANEL AND LOCK THE...
Page 9
3-Wire Flat Power Cord Installation Fig. 2.1 Screws (See Figures 2.1 and 2.2) 1. Remove the Terminal Block Access Plate on the back of the range by unscrewing the 4 fixing Screws. 2. Insert the Flat Power Cord through the Bracket; then tighten the Flat Power Cord by using the Strain Relief.
Page 10
3-Wire Power Cord Installation Fig. 2.3 (See Figures 2.1, 2.3, 2.4 and 2.5) Bracket 1. Remove the Terminal Block Access Plate on the back of the Fixing Screws range by unscrewing the 4 fixing Screws (fig. 2.1). 2. Remove the Bracket and Strain Relief group by unscrewing the Bracket Fixing Screws (fig.
Page 11
3-Wire Conduit Installation Fig. 2.7 (See Figures 2.1, 2.7, 2.8 and 2.9) Bracket 1. Remove the Terminal Block Access Plate on the back of the Fixing Screws range by unscrewing the 4 fixing Screws (fig. 2.1). 2. Remove the Bracket and Strain Relief group by unscrewing the Bracket Fixing Screws (2.7).
Page 12
DRAWER VARMING EXT. ELEMENT BOTTOM ELEMENT INT. ELEMENT BOTTOM ELEMENT GRILL ELEMENT CIRCULAR...
Page 16
The manufacturer cannot be held responsible for possible inaccuracies due to printing or transcription errors in the present booklet. The manufacturer reserves the right to make all modifications to its products deemed necessary for manufacture or commercial reasons at any moment and without prior notice, without jeopardising the essential functional and safety characteristics of the appliances.