Table of Contents
Advertisement
Quick Links
GAS/ELECTRIC RANGE
for residential use only
DEGESC 24 SS
Model:
• INSTALLATION INSTRUCTIONS
IMPORTANT - PLEASE READ AND FOLLOW
IMPORTANT - PLEASE READ AND FOLLOW
Before beginning, please read these instructions completely and carefully.
Do not remove permanently affixed labels, warnings, or plates from the product. This
may void the warranty.
Please observe all local and national codes and ordinances.
Please ensure that this product is properly grounded.
The installer should leave these instructions with the consumer who should retain
for local inspector's use and for future reference.
Installation must conform with local codes or in the absence of codes, the National Fuel
Gas Code ANSIZ223.1 - Iatest edition. Electrical installation must be in accordance with the
National Electrical Code, ANSI/NFPA70 - latest edition and/or local codes. IN CANADA:
Installation must be in accordance with the current CAN/CGA-B149.1 National Gas
Installation Code or CAN/CGA-B149.2, Propane Installation Code and/or local codes.
Electrical installation must be in accordance with the current CSA C22.1 Canadian
Electrical Codes Part 1 and/or local codes.
INSTALLATION IN MANUFACTURED (MOBILE) HOME: The installation must conform with
the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 [for-
merly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part
280)] or, when such standard is not applicable, the Standard for Manufactured Home
Installations, ANSI/NCSBCS A225.1, or with local codes where applicable.
INSTALLATION IN RECREATIONAL PARK TRAILERS: The installation must conform with
state or other codes or, in the absence of such codes, with the Standard for Recreational
Park Trailers, ANSI A119.5.
Installation of any gas-fired equipment should be made by a Iicensed plumber. A manual
gas shut-off valve must be installed in the gas supply line ahead of the appliance in the gas
stream for safety and ease of service.
If an external electrical source is utilized, the appliance, when installed, must be electrical-
ly grounded in accordance with local codes or, in the absence of local codes, with the
national Electrical Code, ANSI/NFPA 70.
This range is supplied with a protective film on
This film must be removed before installing/using the appliance.
FOR INSTALLER ONLY
THIS RANGE IS FOR RESIDENTIAL USE ONLY
steel and aluminium parts.
Advertisement
Table of Contents
Related Manuals for DeLonghi DEGESC24SS
Summary of Contents for DeLonghi DEGESC24SS
- Page 1 Electrical Code, ANSI/NFPA 70. This range is supplied with a protective film on This film must be removed before installing/using the appliance. FOR INSTALLER ONLY THIS RANGE IS FOR RESIDENTIAL USE ONLY steel and aluminium parts.
-
Page 2: See Installation Instructions
• lf you cannot reach your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, service agency, or the gas supplier. WARNING • ALL RANGES CAN TIP • INJURY TO PERSON COULD RESULT • INSTALL ANTI-TIP DEVICE PACKED WITH RANGE • SEE INSTALLATION INSTRUCTIONS... - Page 3 DATA PLATE CONVERSION LABEL This appliance is designed and manufactured solely for the cooking of domestic (household) food and in not suitable for any none domestic application and therefore should not be used in a commercial environmement. The appliance guarantee will be void if the appliance is used within a none domestic environnement i.e.
-
Page 4: Installation Instructions
INSTALLATION INSTRUCTIONS WARNING! THIS APPLIANCE HAS TO BE INSTALLED BY A QUALIFIED INSTALLER. Improper installation, adjustment, alteration, services, or maintenance can cause injury or property damage. Consult a qualified installer, service agent, or the gas supplier. IMPORTANT: The use of suitable protective clothing/gloves is recommended when handling, installing of this appliance. TOOLS NEEDED FOR INSTALLATION (NOT SUPPLIED WITH THE APPLIANCE) T-handle... -
Page 5: General Information
14. When installing or removing the range for service, a rolling lift jack should be used. Do not push against any of the edges of the range in an attempt to slide it into or out of the installation. Pushing or pulling a range (rather than using a lift jack) also increases the possibility of bending the leg spindles or the internal coupling connectors. -
Page 6: Installation
30” (762 mm) above the countertop for a width of minimum 24” (609.6 mm): it has to be centred with the range. Side wall cab- inets above the range must be a minimum of 18” (457 mm) above the countertop. -
Page 7: Assembling The Backguard
PROXIMITY TO SIDE CABINETS 1 3 " m a x . (3 3 0 m m ) Fig. 1.3 Fig. 1.4 ASSEMBLING THE BACKGUARD It is mandatory to install the backguard Assemble the backguard as shown in figure 1.5: • Screw the 2 screws “A” interposing the spacers. •... -
Page 8: Anti-Tip Stability Device Installation Instructions
4 (four) suitable screws (not supplied). 2. After fixing the anti-tip bracket, slide range into place. Be sure the rear left foot slides under the anti-tip bracket attached. -
Page 9: Gas Connection
The supply line shall be equipped with an approved shutoff valve. This valve should be located in the same room as the range and should be in a location that allows ease of opening and closing (in a position where it can be reached quickly in the event of an emergency). - Page 10 STEP 2 Assemble the 1/2” NPT connector + pressure regulator group to the extension pipe interposing the gasket supplied. The regulator cover must be oriented toward the front side of the range. IMPORTANT: use two spanners to tighten the connection.
- Page 11 Gasket 1/2” NPT (conical) male Pressure regulator Manifold male pipe fitting 1/2” G cylindrical (ISO 228-1) female To range Extension pipe 1/2” G cylindrical (ISO 228-1) male 1/2” G cylindrical (ISO 228-1) female Connector 1/2” NPT female 1/2”...
-
Page 12: Flexible Connections
(Gas conversions are the responsibility of the dealer or end user.) c) This range can be used with NATURAL or LP/PROPANE gas. It is shipped from the factory adjusted for use with NATURAL gas. -
Page 13: Conversion To Lp/Propane Gas
CONVERSION TO LP/PROPANE GAS Every range is provided with a set of injectors for the various types of gas. Select the injectors to be replaced according to the “INJECTORS TABLE”. The nozzle diameters, expressed in hundredths of a millimetre, are marked on the body of each injector. - Page 14 2. Unscrew the A component, reverse and screw it according Fitting the warming drawer (fig. 2.10): 1. Insert the drawer guides into the range guides (fig. 2.10) 2. Gently close the drawer completely; the safety catchs will be automatically hooked.
-
Page 15: Injectors Table
INJECTORS TABLE NOMINAL REDUCED POWER POWER BURNERS BTU/hr BTU/hr Auxiliary (AUX) 3500 1000 Semirapid (SR) 6000 1500 Triple ring (TC) 12000 5000 OPERATIONS TO BE PERFORMED WHEN SUBSTITUTING THE INJECTORS Remove the gratings, the burner covers and the knobs; Using a wrench substitute the nozzle injectors “J” (figs. 2.11 - 2.12) with those most suitable for the kind of gas for which it is to be used. -
Page 16: Electrical Connection
4-wire power supply cord kit. The cord must be secured to the range with the strain relief supplied or with a suitable strain relief. The electrical connection is made at the terminal block, which is located behind the terminal block access plate on the back of the range. - Page 17 Terminal Block. 3. Remove the 3 wire terminal nuts and washers from the Terminal Block. 4. Remove the Ground Strap from the frame of range and ter- minal by removing its screw and cutting it as shown in Figure 3.3.
- Page 18 2. Remove the Bracket and Strain Relief Group by unscrewing the Bracket Fixing Screws. 3. Mount the Power Cord Bracket (supplied with the range in a separate kit) inside the Opening For Electrical Connection by screwing the 2 Fixing Screws (as indicated in Figure 3.5).
- Page 19 2. Remove the Bracket and Strain Relief group by unscrewing the Bracket Fixing Screws. 3. Mount the Conduit Bracket (supplied with the range in a sep- arate kit) inside the Opening For Electrical Connection by screwing the 2 Fixing Screws (as indicated in Figure 3.8).
- Page 20 DRAWER VARMING EXT. ELEMENT BOTTOM ELEMENT INT. ELEMENT BOTTOM ELEMENT GRILL ELEMENT CIRCULAR...
- Page 24 The manufacturer cannot be held responsible for possible inaccuracies due to printing or transcription errors in the present booklet. The manufacturer reserves the right to make all modifications to its products deemed necessary for manufacture or commercial reasons at any moment and without prior notice, without jeopardising the essential functional and safety characteristics of the appliances.