Table of Contents
Advertisement
DOUBLE OVEN GAS RANGE
for residential use only
DEFSGG 36 D..
Models:
• INSTALLATION INSTRUCTIONS
IMPORTANT - PLEASE READ AND FOLLOW
IMPORTANT - PLEASE READ AND FOLLOW
Before beginning, please read these instructions completely and carefully.
Do not remove permanently affixed labels, warnings, or plates from the product. This
may void the warranty.
Please observe all local and national codes and ordinances.
Please ensure that this product is properly grounded.
The installer should leave these instructions with the consumer who should retain
for local inspector's use and for future reference.
The electrical plug should always be accessible.
Installation must conform with local codes or in the absence of codes, the National Fuel
Gas Code ANSIZ223.1 - Iatest edition. Electrical installation must be in accordance with the
National Electrical Code, ANSI/NFPA70 - latest edition and/or local codes. IN CANADA:
Installation must be in accordance with the current CAN/CGA-B149.1 National Gas
Installation Code or CAN/CGA-B149.2, Propane Installation Code and/or local codes.
Electrical installation must be in accordance with the current CSA C22.1 Canadian
Electrical Codes Part 1 and/or local codes.
INSTALLATION IN MANUFACTURED (MOBILE) HOME: The installation must conform with
the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 [for-
merly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part
280)] or, when such standard is not applicable, the Standard for Manufactured Home
Installations, ANSI/NCSBCS A225.1, or with local codes where applicable.
INSTALLATION IN RECREATIONAL PARK TRAILERS: The installation must conform with
state or other codes or, in the absence of such codes, with the Standard for Recreational
Park Trailers, ANSI A119.5.
Installation of any gas-fired equipment should be made by a Iicensed plumber. A manual
gas shut-off valve must be installed in the gas supply line ahead of the appliance in the gas
stream for safety and ease of service.
If an external electrical source is utilized, the appliance, when installed, must be electrical-
ly grounded in accordance with local codes or, in the absence of local codes, with the
national Electrical Code, ANSI/NFPA 70.
This range is supplied with a protective film on
This film must be removed before installing/using the appliance.
FOR INSTALLER ONLY
THIS RANGE IS FOR RESIDENTIAL USE ONLY
steel and aluminium parts.
Advertisement
Table of Contents
Related Manuals for DeLonghi DEFSGG 36
Summary of Contents for DeLonghi DEFSGG 36
- Page 1 DOUBLE OVEN GAS RANGE for residential use only DEFSGG 36 D.. Models: • INSTALLATION INSTRUCTIONS IMPORTANT - PLEASE READ AND FOLLOW IMPORTANT - PLEASE READ AND FOLLOW Before beginning, please read these instructions completely and carefully. Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.
-
Page 2: See Installation Instructions
WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. WHAT TO DO IF YOU SMELL GAS: •... - Page 3 DATA PLATE CONVERSION LABEL This appliance is designed and manufactured solely for the cooking of domestic (household) food and in not suitable for any none domestic application and therefore should not be used in a commercial environmement. The appliance guarantee will be void if the appliance is used within a none domestic environnement i.e.
-
Page 4: Installation Instructions
INSTALLATION INSTRUCTIONS WARNING! THIS APPLIANCE HAS TO BE INSTALLED BY A QUALIFIED INSTALLER. Improper installation, adjustment, alteration, services, or maintenance can cause injury or property damage. Consult a qualified installer, service agent, or the gas supplier. IMPORTANT: The use of suitable protective clothing/gloves is recommended when handling, installing of this appliance. TOOLS NEEDED FOR INSTALLATION T-handle Tape... -
Page 5: General Information
Natural gas - 4.0” W.C.P. LP/Propane - 11.0” W.C.P. 13. The misuse of oven door (e.g. stepping, sitting, or leaning on them) can result in potential hazards and/or injuries. 14. When installing or removing the range for service, a rolling lift jack should be used. -
Page 6: Installation
PROXIMITY TO SIDE CABINETS 1. This range may be installed directly adjacent to existing 36" (914 mm) high base cabinets. Range dimensions: • width: 35” 7/8 (911 mm) • depth: 23” 31/32 (609 mm) • height (without backguard / island trim): MIN 35” 7/16 (900 mm) MAX 37”... - Page 7 GAS AND ELECTRIC CONNECTION Rif. inch 7” 15/32 15” 5” 7” 1/8 ÷ 3/32 20” * : Depending on feet regulation Area for ELECTRICAL connection Fig. 1.2 130 ÷ 180 Dotted line showing the position of the range when installed Area for GAS connection...
- Page 8 ( 3 3 0 m m ) 1 3 " m a x . PROXIMITY TO SIDE CABINETS RANGE WITH BACKGUARD Fig. 1.3a 1 3 " m a x . ( 3 3 0 m m ) Fig. 1.3b...
- Page 9 1 3 " m a x . ( 3 3 0 m m ) PROXIMITY TO SIDE CABINETS RANGE WITH ISLAND TRIM Fig. 1.3c ( 3 3 0 m m ) 1 3 " m a x . Fig. 1.3d...
-
Page 10: Fitting The Adjustable Feet
0 mm 0" + 1" 31/32 Fig. 1.6 + 50 mm Fig. 1.7a Fig. 1.4 FITTING THE ADJUSTABLE FEET The adjustable feet must be fitted to the base of the cooker before use. Rest the rear of the cooker on a piece of the polystyrene packaging exposing the base for the fitting of the feet. - Page 11 Fig. 1.8 ASSEMBLING THE BACKGUARD OR THE ISLAND TRIM It is mandatory to install the backguard or the island trim • Assemble the backguard or the island trim as shown in figure 1.8 or 1.9 and fix it by screw- ing the 5 screws “A”...
-
Page 12: Anti-Tip Stability Device Installation Instructions
YOU MUST USE STABILITY ANTI TIP BRACKET TO PREVENT UNIT FROM TIPPING. Slot for inserting the anti-tip bracket ANTI-TIP STABILITY DEVICE INSTALLATION INSTRUCTIONS 1. The anti-tip bracket has to be attached as shown on figure below, it has to be fixed on the rear wall by no. -
Page 13: Gas Connection
All gas connections must be made according to national and local codes. This gas supply (service) line must be the same size or greater than the inlet line of the appliance. Sealant on all pipe joints must be resistant to te action of LP/Propane gas. - Page 14 PRESSURE REGULATOR INSTALLATION STEP 1 Mount the 1/2” NPT (conical) male connector to the pressure regulator and tighten by using a wrench. Do not over tighten the connector. Over tightening may crack regulator. STEP 2 Assemble the 1/2” NPT connector + pressure regulator group to the extension pipe interposing the gasket supplied.
- Page 15 STEP 3 Insert the extension pipe + pressure regulator group in the “A” bracket. STEP 4 Assemble the extension pipe + pressure regulator group to the range manifold interposing the gasket supplied. The regulator cover must be ordiented toward the front side of the range.
- Page 16 STEP 5 Fix the “B” bracket on the back of the range by the 2 (two) screws supplied with the kit for gas connection. The regulator cover must be ordiented toward the front side of the range. Fig. 2.2e...
- Page 17 PRESSURE REGULATOR INSTALLATION Manifold male pipe fitting 1/2” G cylindrical (ISO 228-1) female Extension pipe Fig. 2.3 To range Range manifold 1/2” G cylindrical (ISO 228-1) male Gasket Extension pipe female f i t pipe fitting Extension Gasket pipe male pipe fitting 1/2”...
-
Page 18: Flexible Connections
TEST POINT ADAPTER The Test Point adapter is available from the After-Sales Service. Fig. 2.4 c) Any conversion required must be performed by your dealer or a qualified licensed plumber or gas service company. Please provide the service person with this manual before work is started on the range. -
Page 19: Conversion To Lp/Propane Gas
LP/PROPANE NATURAL GAS REGULATION REGULATION CONVERSION TO LP/PROPANE GAS Every range is provided with a set of injectors for the various types of gas. Select the injectors to be replaced according to the “INJECTORS TABLE”. The nozzle diameters, expressed in hundredths of a millimetre, are marked on the body of each injector. -
Page 20: Injectors Table
16000 for NATURAL GAS (#) Outer crowns 15000 for LP/PROPANE GAS (#) Oven burner (left) Oven burner (right) Broil burner (left) Broil burner (right) (*) Power calculated only with inner crown operating (#) Power calculated with inner and outer crowns operating... - Page 21 SETTING THE BURNER MINIMUM When switching from one type of gas to another, the minimum flow rate must also be correct: the flame should not go out even when passing suddenly from maximum to minimum flame. To regulate the flame follow the instructions below: Semirapid and triple ring burners –...
- Page 22 – Lift and remove the lower panel inside the oven. – Remove the burner securing screw (fig. 2.9). – Withdraw the burner as shown in figure 2.10 and rest it inside the oven. Take care not to damage the wire to the ignition electrode and the safety valve probe.
-
Page 23: Adjustment Of The Oven Burner Minimum
ADJUSTMENT OF THE OVEN BURNER MINIMUM (LEFT and RIGHT OVEN) This needs to be done only for the oven burner (the broil is a fixed capacity) by acting on the thermostat in the following way: – Turn on the burner by setting the thermostat knob on position –... -
Page 24: Electrical Connection
WARNING Electrical Shock Hazard Plug into a grounded 3-prong outlet. Do not remove ground prong. Do not use an adapter. Failure to follow these instructions can result in death, fire, or electrical shock. Fig. 3.1 WARNING VERY IMPORTANT Before any operation of maintenance disconnect the appliance from the electrical mains supply. -
Page 25: Wiring Diagram
ELECTRIC DIAGRAM KEY RIGHT OVEN Switch Security switch Cooling fan failure lamp Oven lamp Air switch Fan motor TL1/2 Thermal overload Ignition switches group Ignition coil LEFT OVEN Switch Security switch Oven lamp Electronic clock Fan motor Ignition switches group... - Page 28 The manufacturer cannot be held responsible for possible inaccuracies due to printing or transcription errors in the present booklet. The manufacturer reserves the right to make all modifications to its products deemed necessary for manufacture or commercial reasons at any moment and without prior notice, without jeopardising the essential functional and safety characteristics of the appliances.