Table of Contents
Advertisement
Quick Links
DUAL FUEL SELF CLEANING RANGE
for residential use only
DL 48 P6G
Models:
DL 48 P6GE
• INSTALLATION INSTRUCTIONS
IMPORTANT - PLEASE READ AND FOLLOW
IMPORTANT - PLEASE READ AND FOLLOW
Before beginning, please read these instructions completely and carefully.
Do not remove permanently affixed labels, warnings, or plates from the product. This
may void the warranty.
Please observe all local and national codes and ordinances.
Please ensure that this product is properly grounded.
The installer should leave these instructions with the consumer who should retain
for local inspector's use and for future reference.
Installation must conform with local codes or in the absence of codes, the National Fuel
Gas Code ANSIZ223.1 - Iatest edition. Electrical installation must be in accordance with the
National Electrical Code, ANSI/NFPA70 - latest edition and/or local codes. IN CANADA:
Installation must be in accordance with the current CAN/CGA-B149.1 National Gas
Installation Code or CAN/CGA-B149.2, Propane Installation Code and/or local codes.
Electrical installation must be in accordance with the current CSA C22.1 Canadian
Electrical Codes Part 1 and/or local codes.
INSTALLATION IN MANUFACTURED (MOBILE) HOME: The installation must conform with
the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 [for-
merly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD (Part
280)] or, when such standard is not applicable, the Standard for Manufactured Home
Installations, ANSI/NCSBCS A225.1, or with local codes where applicable.
INSTALLATION IN RECREATIONAL PARK TRAILERS: The installation must conform with
state or other codes or, in the absence of such codes, with the Standard for Recreational
Park Trailers, ANSI A119.5.
Installation of any gas-fired equipment should be made by a Iicensed plumber. A manual
gas shut-off valve must be installed in the gas supply line ahead of the appliance in the gas
stream for safety and ease of service.
If an external electrical source is utilized, the appliance, when installed, must be electrical-
ly grounded in accordance with local codes or, in the absence of local codes, with the
national Electrical Code, ANSI/NFPA 70.
This range is supplied with a protective film on
This film must be removed before installing/using the appliance.
FOR INSTALLER ONLY
THIS RANGE IS FOR RESIDENTIAL USE ONLY
steel and aluminium parts.
Advertisement
Table of Contents
Related Manuals for DeLonghi DL 48 P6G
Summary of Contents for DeLonghi DL 48 P6G
- Page 1 DUAL FUEL SELF CLEANING RANGE for residential use only DL 48 P6G Models: DL 48 P6GE • INSTALLATION INSTRUCTIONS IMPORTANT - PLEASE READ AND FOLLOW IMPORTANT - PLEASE READ AND FOLLOW Before beginning, please read these instructions completely and carefully.
-
Page 2: See Installation Instructions
• lf you cannot reach your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, service agency, or the gas supplier. WARNING • ALL RANGES CAN TIP • INJURY TO PERSON COULD RESULT • INSTALL ANTI-TIP DEVICE PACKED WITH RANGE • SEE INSTALLATION INSTRUCTIONS... - Page 3 DATA PLATE CONVERSION LABEL This appliance is designed and manufactured solely for the cooking of domestic (household) food and in not suitable for any none domestic application and therefore should not be used in a commercial environmement. The appliance guarantee will be void if the appliance is used within a none domestic environmement i.e.
-
Page 4: Installation Instructions
INSTALLATION INSTRUCTIONS WARNING! THIS APPLIANCE HAS TO BE INSTALLED BY A QUALIFIED INSTALLER. Improper installation, adjustment, alteration, services, or maintenance can cause injury or property damage. Consult a qualified installer, service agent, or the gas supplier. IMPORTANT: The use of suitable protective clothing/gloves is recommended when handling, installing of this appliance. TOOLS NEEDED FOR INSTALLATION T-handle Tape... -
Page 5: General Information
14. When installing or removing the range for service, a rolling lift jack should be used. Do not push against any of the edges of the range in an attempt to slide it into or out of the installation. Pushing or pulling a range (rather than using a lift jack) also increases the possibility of bending the leg spindles or the internal coupling connectors. -
Page 6: Installation
Gas line opening: Wall - 21 /32” (16.5 mm) from the left/right sides to centre of range; from 4” 7/32 (107 mm) to 4" 11 /16 (119 mm) [depend- ing on feet regulation] from the floor. This area can be extend- ed on left/right sides: 15"... - Page 7 GAS AND ELECTRIC CONNECTION Rif. inch 15” 2” 51/64 ” 21/32 4” 4” 7/32 - 11/16 * : Depending on feet regulation Area for GAS and ELECTRIC connection Fig. 1.2 16.5 107 - 119 Dotted line showing the posi- tion...
- Page 8 ( 3 3 0 m m ) PROXIMITY TO SIDE CABINETS 1 3 " m a x . RANGE WITH BACKGUARD 1 3 " m a x . ( 3 3 0 m m ) Fig. 1.3a Fig. 1.3b...
- Page 9 1 3 " m a x . ( PROXIMITY TO SIDE 3 3 0 m m ) CABINETS RANGE WITH ISLAND TRIM Fig. 1.3c ( 3 3 0 m m ) 1 3 " m a x . Fig. 1.3d...
- Page 10 Fig. 1.4 ASSEMBLING THE BACKGUARD OR THE ISLAND TRIM It is mandatory to install the backguard or the island trim • Assemble the backguard or the island trim as shown in figure 1.4 or 1.5 and fix it by screw- ing the 5 screws “A”.
- Page 11 LEVELLING THE RANGE The range is equipped with 6 LEVELLING FEET (already fitted on the appliance) and may be levelled by screwing or unscrewing the feet (fig. 1.9). It is important to observe the prescriptions of figures 1.6, 1.7, 1.8.
-
Page 12: Anti-Tip Stability Device Installation Instructions
4 (four) suitable screws (not supplied). 2. After fixing the anti-tip bracket, slide range into place. Be sure the rear central foot slides under the anti-tip bracket attached. -
Page 13: Gas Connection
The supply line shall be equipped with an approved shutoff valve. This valve should be located in the same room as the range and should be in a location that allows ease of opening and closing (in a position where it can be reached quickly in the event of an emergency). - Page 14 STEP 2 Assemble the 1/2” NPT connector + pressure regulator group to the extension pipe interposing the gasket supplied. The regulator cover must be oriented toward the front side of the range. IMPORTANT: use two spanners to tighten the connection.
- Page 15 (ISO 228-1) female Connector 1/2” NPT female 1/2” NPT female WARNING: check the right positioning of the gas regulator. The arrow on the back of the gas regulator must be oriented toward the connector. To range To mains connection Arrow Fig. 2.3...
-
Page 16: Flexible Connections
(Gas conversions are the responsibility of the dealer or end user.) c) This range can be used with NATURAL or LP/PROPANE gas. It is shipped from the factory adjusted for use with NATURAL gas. -
Page 17: Conversion To Lp/Propane Gas
CONVERSION TO LP/PROPANE GAS Every range is provided with a set of injectors for the various types of gas. Select the injectors to be replaced according to the “INJECTORS TABLE”. The nozzle diameters, expressed in hundredths of a millimetre, are marked on the body of each injector. - Page 18 Pressure regulator REGULATOR COVER Fitting the warming drawer (fig. 2.9): 1. Insert the drawer guides into the range guides (fig. 2.9) 2. Gently close the drawer completely; the safety catchs will be automatically hooked. NATURAL GAS REGULATION Fig. 2.9 Fig.
-
Page 19: Injectors Table
INJECTORS TABLE NOMINAL POWER BURNERS BTU/hr Rapid (R) 10000 Triple ring (TC) 12000 2800 for NATURAL GAS (*) Inner crown 3500 for LP/PROPANE GAS (*) Dual (D) 16000 for NATURAL GAS (#) Outer crowns 15000 for LP/PROPANE GAS (#) Griddle 12000 (*) Power calculated only with inner crown operating (#) Power calculated with inner and outer crowns operating... - Page 20 Fig. 2.11 Fig. 2.12 Fig. 2.14 OPERATIONS TO BE EXECUTED FOR THE REPLACEMENT OF THE INJECTOR OF THE GRIDDLE BURNER Lift and remove the griddle stainless steel plate. Unscrew the no. 2 (two) screws and remove the plate "B" (fig. 2.11). Unscrew the no.
- Page 21 Remove the burner as shown in figure 2.17. Using a 7 mm box spanner, unscrew the injector (indicated by the arrow in fig. 2.18) and replace it by the proper one according to the kind of gas. Then replace the burner and other components repeating the above steps in reverse order.
- Page 22 After regulation repeat the operations indicated in paragraph “2. Pressure regulator” at page 13. If the range has been disconnected and then connected again to the gas supply line repeat the operations indicated in paragraph “5. Leak Testing” at page 16.
-
Page 23: Electrical Connection
4-wire connector directions. The conduit must be secured to the range with the strain relief bracket. The electrical connection is made at the terminal block which is located behind the access door on the back of the range. WARNING... - Page 24 (See Figures 3.1 and 3.2) 1. Remove the Terminal Block Access Plate on the back of the range by unscrewing the 4 fixing Screws (Figure 3.1). 2. Insert the Flat Power Cord through the Bracket; then tighten the Flat Power Cord by using the Strain Relief. Allow enough slack to easily attach the cord terminals to the Terminal Block (Figure 3.2).
- Page 25 Terminal Block. 5. Remove the 3 wire terminal nuts and washers from the Terminal Block. 6. Remove the Ground Strap from the frame of range and ter- minal by removing its screw and cutting it as shown in Figure 3.6.
- Page 26 2. Remove the Bracket and Strain Relief group by unscrewing the Bracket Fixing Screws (Figure 3.7). 3. Mount the Conduit Bracket (supplied with the range in a sep- arate kit - make sure you are using the correct Conduit Bracket as indicated in Figure 3.8) inside the Opening For Electrical Connection by screwing the 2 Fixing Screws (as indicated in Figure 3.8).
- Page 27 EXT. ELEMENT BOTTOM ELEMENT INT. ELEMENT BOTTOM ELEMENT GRILL ELEMENT CIRCULAR DRAWER VARMING RIGHT DRAWER VARMING LEFT EXT. ELEMENT BOTTOM ELEMENT INT. ELEMENT BOTTOM ELEMENT GRILL ELEMENT CIRCULAR...
- Page 28 The manufacturer cannot be held responsible for possible inaccuracies due to printing or transcription errors in the present booklet. The manufacturer reserves the right to make all modifications to its products deemed necessary for manufacture or commercial reasons at any moment and without prior notice, without jeopardising the essential functional and safety characteristics of the appliances.