Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for NEC VERSA P600
Summary of Contents for NEC VERSA P600
- Page 1 Versa P600 Disassembly Manual...
-
Page 2: Table Of Contents
Removing the LCD Module ..........................13 Removing the LCD Penal.............................15 Removing the Top Cover .............................17 Removing the Touch Pad.............................18 Removing the DC/DC Board ..........................20 Removing the Main Board............................21 DIP Switch Setting..............................22 Screws..................................23 Notice ...................................24 NEC Versa P600 Disassembly Manual Page 2... -
Page 3: Overview
Furthermore, the screws that are removed are shown next to the image of the parts themselves. NEC reserves the right to make changes to the Versa P600 chassis without notice. Technician Notes Only technicians authorized by NEC Computers International BV should attempt to repair this equipment. -
Page 4: Hazardous Voltage
Inside the power supply are hazardous avviare il sistema senza aver prima messo a voltages that can cause serious personal injury. Always posto il coperchio return a defective power supply to your dealer. NEC Versa P600 Disassembly Manual Page 4... -
Page 5: Removing The Battery
Removing the Battery Perform the following steps to remove the battery: 1. Make sure to power off the Versa P600. 2. Turn the unit upside down. 3. Unlock the battery and slide it out of its place as the arrow shows in Fig. 1 Fig. -
Page 6: Removing The Mdc Modem Module
To remove the MDCmodem module, first remove the hard disk drive (see Removing the Hard Disk Drive), then perform the following steps: 1. Remove the screw shown in Fig. 5 M2.5x3.5 Sliver Fig. 5 Removing the screws on the MCD modem NEC Versa P600 Disassembly Manual Page 6... -
Page 7: Removing The Keyboard Cover
2. Remove the Keyboard Cover as shown in Fig. 7 Fig. 7 Removing the Keyboard Cover Removing the Keyboard To remove the Keyboard module, first remove the keyboard cover (see Removing keyboard cover), then perform the following steps: NEC Versa P600 Disassembly Manual Page 7... -
Page 8: Removing The Optical Drive & Heat Plate
To remove the optical drive & heat plate, first remove the keyboard cover (see Removing the keyboard cover), remove the keyboard (see Removing the keyboard) then perform the following steps: 1. Remove the screw as shown in Fig. 10 NEC Versa P600 Disassembly Manual Page 8... - Page 9 2. Push the Optical Drive module out from the base unit as shown in Fig. 11 Fig. 11 Pushing Optical Drive module out from base unit 3. Carefully remove the heat plate from the base unit. NEC Versa P600 Disassembly Manual Page 9...
-
Page 10: Removing The Memory Module
1. Unclip memory module as shown in Fig. 13 Fig. 13 Removing the memory module 2. Remove the Memory Module from its slot and put it aside. NEC Versa P600 Disassembly Manual Page 10... -
Page 11: Removing The Wireless Module
Removing optical drive & heat plate) then perform the following steps: 1. Release the screws on the heat sink in descending order (4 3 2 1) as shown in Fig. 15 M2.5x11 Black NEC Versa P600 Disassembly Manual Page 11... - Page 12 Fig. 16 Removing the heat sink 3. Use flat screws driver to release the CPU from the CPU socket; carefully lift up the CPU and put it in a safe place. Fig. 17 Releasing the CPU NEC Versa P600 Disassembly Manual Page 12...
-
Page 13: Removing The Lcd Module
2. Remove the LCD cable cover with a small flat screws driver as shown in Fig. 19 . Fig. 19 Removing the LCD cable Cover 3. Release the screws at rear side of the unit as shown in Fig. 20 NEC Versa P600 Disassembly Manual Page 13... - Page 14 4. Unscrew the two screws located on the bottom of the unit as shown in Fig. 21 M2x6 Black Fig. 21 LCD hinge screws at the bottom 5. Carefully lift the LCD module out of the system and put it aside. NEC Versa P600 Disassembly Manual Page 14...
-
Page 15: Removing The Lcd Panel
Release the LCD Bezel carefully and put it aside as shown in Fig. 23 Fig. 23 Removing the LCD Bezel 3. Unscrew all screws encircled in Fig. 24 disconnect the inverter board and put it aside. NEC Versa P600 Disassembly Manual Page 15... - Page 16 5. Remove the screws at both sides of the LCD panel in order to release the LCD hinges as shown in Fig. 25 . Fig. 25 Removing the LCD Panel hinges M2x3.5 Silver NEC Versa P600 Disassembly Manual Page 16...
-
Page 17: Removing The Top Cover
A = M2x15 Black Fig. 27 Removing the Top cover screws on the bottom of the system B = M2.5x11 Black 4. Remove all screws in the battery compartment as shown in Fig. 28 NEC Versa P600 Disassembly Manual Page 17... -
Page 18: Removing The Touch Pad
Removing the Touch Pad To remove the Touch Pad, first remove the Top Cover (see Removing the Top Cover), then perform the following steps: NEC Versa P600 Disassembly Manual Page 18... - Page 19 1. On the other side of the top cover unscrew the two screws on the Touch Pad assembly as shown in Fig. 30 and remove the Touch Pad assy from the palm rest. M2x3.5 Silver Fig. 30 Touch Pad Assembly NEC Versa P600 Disassembly Manual Page 19...
-
Page 20: Removing The Dc/Dc Board
1. Remove the screw on the DC/DC board as shown in Fig. 31 M2.5x11 Black Fig. 31 DC/DC Board 2. Carefully remove the DC/DC board as shown in Fig. 32 and put it aside. Fig. 32 Removing the DC/DC Board NEC Versa P600 Disassembly Manual Page 20... -
Page 21: Removing The Main Board
2. Disconnect the VGA connector from the base as shown in Fig. 34 Fig. 34 Disconnecting the VGA connector M2.5x10 silver 3. Lift the main board out of the system and put it aside (Fig. 35 ). NEC Versa P600 Disassembly Manual Page 21... -
Page 22: Dip Switch Setting
ON : connect to GND OFF : NC Bit6 Password Password override. ON: Override OFF: Available (factory setting) Bit 1 Bit 2 Keyboard code OFF US Keyboard OFF JP Keyboard Reserved UK Keyboard NEC Versa P600 Disassembly Manual Page 22... -
Page 23: Screws
Screws M2.5x5.6 Silver M2.5x3.5 Silver M2.5x8 Sliver M2.5x10 Silver M2.5x11 Black M2.5x12.5 Silver M2.5x15 Black M2x3 Sliver M2x6 Black M3x4 Black M2.5x5 Sliver NEC Versa P600 Disassembly Manual Page 23... -
Page 24: Notice
This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in any form or by any means without prior written consent from NEC Computers International BV. NEC COMPUTERS INTERNATIONAL BV SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN;...