Dimplex BFSL33 Service Manual
Hide thumbs
Also See for BFSL33:
- Owner's manual (39 pages) ,
- Installation manual (22 pages) ,
- Installation manual (19 pages)
Table of Contents
Advertisement
IMPORTANT SAFETY INFORMATION: Always read this manual first before attempting to service this
fireplace. For your safety, always comply with all warnings and safety instructions contained in this
manual to prevent personal injury or property damage.
Dimplex North America Limited
1367 Industrial Road Cambridge ON Canada N1R 7G8
1-888-346-7539 www.dimplex.com
In keeping with our policy of continuous product development, we reserve the right to make changes without notice.
© 2012 Dimplex North America Limited
Service Manual
Model
BFSL33
UL Part Number
6905280100
REV
PCN
DATE
00
-
5-APR-12
7400440000R00
Advertisement
Table of Contents
Related Manuals for Dimplex BFSL33
Summary of Contents for Dimplex BFSL33
- Page 1 Dimplex North America Limited 1367 Industrial Road Cambridge ON Canada N1R 7G8 DATE 1-888-346-7539 www.dimplex.com 5-APR-12 In keeping with our policy of continuous product development, we reserve the right to make changes without notice. © 2012 Dimplex North America Limited 7400440000R00...
-
Page 2: Table Of Contents
NOTE: Procedures and techniques that are considered important enough to emphasize. CAUTION: Procedures and techniques which, if not carefully followed, will result in damage to the equipment. WARNINg: Procedures and techniques which, if not carefully followed, will expose the user to the risk of fire, serious injury, or death. www.dimplex.com... -
Page 3: Operation
OPERATION CAUTION: If you need to continuously reset the heater, disconnect power and call Dimplex customer service at Figure 1 1-888-DIMPLEX (1-888-346-7539). Remote Control The fireplace is supplied with a radio frequency remote control. This remote control has a range of approximately 50 feet (15.25 m), it does not have to be pointed at the... -
Page 4: Maintenance
MAINTENANCE Voltage Selector Switch The BFSL33 has 2 voltage options at the time of installa- WARNINg: Disconnect all power coming to fireplace tion, 110/120v and 220/240v. The voltage selector switch is at main service panel before attempting maintenance to be set at the time of installation according to the voltage or cleaning to reduce risk of fire, shock or damage to coming from the power supply. -
Page 5: Exploded Parts Diagram
EXPLODED PARTS DIAgRAM Glass Accessory Replacement Parts: Remote Control ....3000370600RP Log Set Assembly ....0439560100RP Flicker Motor . -
Page 6: Wiring Diagram
WIRINg DIAgRAM www.dimplex.com... -
Page 7: Remote Receiver Board And Logset Driver Board Replacement
REMOTE RECEIVER BOARD Carefully lift the partially reflective glass out of the fireplace and set aside in a safe location. AND LOgSET DRIVER BOARD Remove the defective board by removing the 4 REPLACEMENT mounting screws on each corner of the board. Tools Required: Phillips Head Screwdriver Remove the wires attached to the original board and Flat Head Screwdriver... -
Page 8: Flicker Motor Replacement
Disconnect the 3 flicker motor wires, which are Snip the plastic wire ties which secure the internal connected in the terminal block (mounted on the wires together to free up the light harness wires. bracket), together with a capacitor, and remove the www.dimplex.com... -
Page 9: Replacement Instructions: Units Secured In Wall
Remove the light strip and harness. Carefully rest the panel inside the lower cavity of the fireplace on its end with the switches near the top. Be Properly orient the new LED strip and reconnect all of careful not to scratch the partially reflective glass. the wiring connections. -
Page 10: Voltage Selector Switch Replacement
Remove the steel curtains by lifting up on the curtain may be necessary to remove. rod releasing it from the center bracket, then sliding Unplug the log set LED wire harness from unit. the rod out from the side mounting tab, and pulling out. www.dimplex.com... -
Page 11: High Temperature Cut-Out Replacement
HIgH TEMPERATURE CUT-OUT RE- Repeat on other side. Remove the 2 screws from the log set retaining plate PLACEMENT along the front of the log set and remove the retaining Tools Required: Phillips Head Screwdriver plate. Flat Head Screwdriver Pull the rear edge of the log set forward by grasping WARNINg: If the fireplace was operating prior to the ember bed by the sides, pull firmly until the rear tab servicing allow at least 10 minutes for light bulbs and... -
Page 12: Blower Assembly Replacement
IMPORTANT: Only handle the log-set by the plastic Remove the 8 screws from the upper air in-take panel ember-bed, not the logs themselves. inside the firebox above the partially reflective glass: 4 on the left and 4 on the right. www.dimplex.com... -
Page 13: Replacement Instructions: Removable Units
wiring connections. NOTE: Log-set fits tightly into firebox. Some force may be necessary to remove. Reassemble in the reverse order as above. Unplug the log set LED wire harness from unit. NOTE: See Helpful Hints Section for reassembly. Loosen the screws on the 2 partially reflective glass SWITCHBOARD REPLACEMENT retaining clips: bottom left side and bottom right side of the rear partially reflective glass panel and turn the... -
Page 14: Heater Element Replacement
3 housing mounting tabs above the fan to servicing allow at least 10 minutes for light bulbs and release from the top panel. heating elements to cool off to avoid accidental burning Remove the wire connections from the heater/blower www.dimplex.com... -
Page 15: Helpful Hints For Reassembly
assembly, noting their original locations Figure 4 NOTE: Using a flat head screwdriver gently pry be- tween the end of the connector and the switch to release the wires. Properly orient the new blower assembly and recon- nect all of the wiring connections. Reassemble in the reverse order as above. -
Page 16: Assembly Component Pictures
LED Light Driver Board Log Set Driver Board Internal Access to Hardwired power connections (panel 3-Light LED Strip removed) and Wire harness LOWER COMPONENT AREA (Logset and Partially Reflective Glass Removed) 3-Light LED Strip and Wire harness Flicker Motor Flicker Rod www.dimplex.com... - Page 17 UPPER COMPONENT AREA Heater Assembly with Upper Vent Panel and Partially Reflective Glass Removed UPPER HOUSINg COMPONENTS Heater Assembly Housing with High Limit Cut Out Blower Motor and Element Connections from the on the top of the Housing Panel and Left Side Right Hand Side Element Connections Voltage Selector Switch and Over Temperature...
-
Page 18: Troubleshooting Guide
Log set dim, not glowing Malfunctioning LED’s in Logset Replace Logset or Driver Board Flame Shudder Defective flicker motor Replace flicker motor Light leaking around the log set Log set not positioned properly Check log set for proper fit www.dimplex.com... - Page 19 PROBLEM CAUSE SOLUTION Heater Heater is not turning off Improper operation Refer to Operation Section Defective Remote Switchboard Replace Remote Switchboard Malfunctioning Wall Controls Refer to Individual Wall Control operating instructions Defective Remote Control Receiver Replace Remote Control Receiver, initialize with Re- mote Control Heater is not turning on Improper operation...