Dimplex BF33STP/DXP Installation Manual
  1. Manuals
  2. Brands
  3. Dimplex Manuals
  4. Indoor Fireplace
  5. BF33STP/DXP
  6. Installation manual
Dimplex BF33STP/DXP Installation Manual

Dimplex BF33STP/DXP Installation Manual

Dimplex bf33stp/dxp fireplaces: install guide
Hide thumbs Also See for BF33STP/DXP:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual
INSTALLATION GUIDE FOR THE
ELECTRIC FIREPLACE
MODEL NUMBERS:
BF33STP/DXP
BF39STP/DXP
7206350300REV01

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BF33STP/DXP and is the answer not in the manual?

Questions and answers

Related Manuals for Dimplex BF33STP/DXP

Summary of Contents for Dimplex BF33STP/DXP

  • Page 1 INSTALLATION GUIDE FOR THE ELECTRIC FIREPLACE MODEL NUMBERS: BF33STP/DXP BF39STP/DXP 7206350300REV01...

  • Page 2: Table Of Contents

    CONTENTS PAGE 1 PAGE 1 PAGE 1 PAGE 2 PAGE 2 PAGE 2 PAGE 3 PAGE 3 PAGE 4 PAGE 5 PAGE 6 - 7 PAGE 8 - 9 PAGE 10 - 11 PAGE 12 - 13 PAGE 14 - 15 PAGE 16 - 18 Listings and Code Approvals Model Specifications...

  • Page 3: Section A

    LISTINGS AND CODE APPROVALS The BF series fireplaces have been tested in accordance with the UL 2021 and CSA C22.2 No. 46 standards for fixed and location-dedicated electric room heaters. MODEL SPECIFICATIONS Model Descriptio Voltage Volts Number 33” 120/120/208/ BF33STP Standard 33”...

  • Page 4: Framing

    SECTION A: FRAMING MODEL BF33STP/DXP 15.0” 33.5” BF39STP/DXP 16.0” 39.5” Rough-in framing dimensions This fireplace is a zero clearance design. No combustibles can be placed on the top surface of the fireplace. Combustibles may be installed to the edge of the unit. Four mounting flanges on the sides of the unit are provided to facilitate installation.

  • Page 5: Voltage Selector Switch Location

    VOLTAGE SELECTOR SWITCH LOCATION IMPORTANT: Ensure that the incoming power supply voltage matches the setting of the voltage selector switch. NOTE: The voltage selector switch is located inside the exhaust panel on the top right hand corner. CAUTION: When changing the voltage selector switch from 240 volts to 120 volts ensure that the power supply is turned off.

  • Page 6: Section C

    SECTION C: FACTORY SETTING WIRING (WITHOUT MAIN POWER WALL SWITCH) IMPORTANT: The unit is factory configured for 208/240 volt operation NOTE: Use 3 conductor wire with ground (4 wires total) from the power supply (breaker panel) to the junction box on the unit. NOTE: All wiring must be completed prior to installing the unit.

  • Page 7: (Without Main Power Wall Switch)

    SECTION C: FACTORY SETTING WIRING (WITHOUT MAIN POWER WALL SWITCH) IMPORTANT: The unit is factory configured for 208/240 volt operation NOTE: Use 2 conductor wire with ground (3 wires total) from the power supply (breaker panel) to the junction box on the unit. NOTE: All wiring must be completed prior to installing the unit.
  • Page 8 SECTION C: FACTORY SETTING WIRING (WITHOUT MAIN POWER WALL SWITCH) (NO HEAT INSTALLATION) IMPORTANT: The unit is factory configured for 208/240 volt operation NOTE: Use 2 conductor wire with ground (3 wires total) from the power supply (breaker panel) to the junction box on the unit.

  • Page 9: Section D

    SECTION D: MAIN POWER WALL SWITCH WIRING OPTIONS MAIN POWER WALL SWITCH WIRING NOTE: This option should not be used with the remote control kit. NOTE: Before installing the unit you must have the following wires installed: 1. A 3 conductor wire with ground (4 wires total) from the power supply panel to the main switch wall box.
  • Page 10 240 VOLT MAIN WALL SWITCH WIRING DIAGRAM WHITE - N WHITE – N 240 V RED – L2 RED – L2 POWER SUPPLY WALL SWITCH BLACK – L1 BLACK – L1 (BREAKER PANEL) GROUND - G GROUND - G...

  • Page 11: Main Power Wall Switch Wiring For 120 Volt

    MAIN POWER WALL SWITCH WIRING NOTE: This option should not be used with the remote control kit. NOTE: Before installing the unit have the following wires installed: 1. A 2 conductor wire with ground (3 wires total) from the power supply panel to the main switch wall box.
  • Page 12 120 VOLT MAIN WALL SWITCH WIRING DIAGRAM WHITE - N WHITE – N RED – L2 120 V POWER BLACK – L1 SUPPLY (BREAKER WALL PANEL) BLACK – L1 SWITCH GROUND - G GROUND - G...

  • Page 13: Main Power Wall Switch Wiring

    MAIN POWER WALL SWITCH WIRING NOTE: This option should not be used with the remote control kit. NOTE: Before installing the unit have the following wires installed: 3. A 2 conductor wire with ground (3 wires total) from the power supply panel to the main switch wall box.
  • Page 14 120 VOLT MAIN WALL SWITCH WIRING DIAGRAM NO HEAT INSTALLATION WHITE - N WHITE – N RED – L2 120 V POWER Wire Nut BLACK – L1 SUPPLY (BREAKER WALL BLACK – L1 PANEL) SWITCH GROUND - G GROUND - G...

  • Page 15: Section E

    SECTION E: HEATER WALL SWITCH AND WALL THERMOSTAT WIRING OPTIONS HEATER WALL SWITCH WIRING NOTE: Before installing the unit complete the following: 1. Install main power connection with appropriate voltage as per Section C or Section D. 2. Install a 2 conductor wire with ground (3 wires total) from the heater switch wall box to the junction box on the unit.
  • Page 16 HEATER WALL SWITCH WIRING DIAGRAM FOR 120/240 VOLT (SEE SECTION C OR SECTION D FOR MAIN POWER CONNECTION) RED – 2 WALL RED – 1 SWITCH GROUND - G...

  • Page 17: Wall Mounted Thermostat Wiring For 120/240 Volt

    WALL MOUNTED THERMOSTAT WIRING NOTE: Before installing the unit complete the following: 1. Install main power connection with appropriate voltage as per Section C or Section D. 2. Install a 2 conductor wire with ground (3 wires total) from the thermostat wall box to the junction box on the unit.
  • Page 18 WALL MOUNTED THERMOSTAT WIRING DIAGRAM FOR 120/240 VOLT (SEE SECTION C OR SECTION D FOR MAIN POWER CONNECTION) CONNECT GROUND TO WALL BOX RED – 2 WALL RED – 1 THERMOSTAT GROUND - G...

  • Page 19: Flame Override Switch Wiring For 120/240 Volt

    FLAME OVERRIDE SWITCH WIRING NOT AVAILABLE WITH NO HEAT INSTALLATION NOTE: The fireplace can be wired to have a wall switch operate the heater independent of the flame NOTE: Before installing the unit complete the following: 1. Install main power connection with appropriate voltage as per Section C or Section D.
  • Page 20 FLAME OVERRIDE WALL SWITCH WIRING DIAGRAM FOR 120/240 VOLT (SEE SECTION C OR SECTION D FOR MAIN POWER C0NNECTION) NOT AVAILABLE WITH NO HEAT INSTALLATION BLUE – 4 WALL BLUE – 3 SWITCH GROUND - G...

  • Page 21: Wiring Diagrams

    WIRING DIAGRAM (BF33STP, BF39STP MODELS)
  • Page 22 WIRING DIAGRAM (BF33DXP, BF39DXP MODELS)

  • Page 23: Wiring Schematic

    WIRING SCHEMATIC (BF33STP, BF39STP MODELS)
  • Page 24 WIRING SCHEMATIC (BF33DXP, BF39DXP MODELS)
  • Page 25 1-888-DIMPLEX 1367 Industrial Road 1-888-346-7539 Cambridge, Ontario Canada, N1R 7G8 Approved for use in the United States and Canada...

This manual is also suitable for:

Bf39stp/dxpBf33stpBf33dxpBf39stpBf39dxp

Table of Contents