Table of Contents
Advertisement
7 – Other Functions
Changing the playback time
display mode
You can select the playback time that is shown on the
display.
During playback or when paused, press the DISPLAY
[LOCK] button on the player or the DISPLAY button on
the remote. Each press of the button cycles through the
three types of time display. The currently selected display
mode is shown in the playback time mode display area.
: total remaining time is displayed
•
T .REMAIN
: remaining time of the current track is
•
REMAIN
displayed
Nothing: elapsed time of the current track is displayed
•
NOTE
When an audio CD is stopped, the total recording time is
•
always shown regardless of whether or not T.REMAIN or
REMAIN appears.
For data CDs, neither the total time when stopped,
•
nor the remaining time or total remaining time during
playback are shown. (Only the number of tracks or track
number appears.)
In program playback mode, remaining time shows
•
the time until playback of the program ends. In single
playback mode, remaining time shows the remaining
time in the track.
In program playback mode, the total time shown is for
•
the program.
The playback time display mode setting is retained even
•
when the power is turned off.
Frame time display setting
You can set whether or not the frame time is shown
during playback. To set the frame time display, use the
menu item (default value:
FRAM
NOTE
The frame time display on/off setting is retained even when
the power is turned off.
End of track warning
(TRACK EOM)
When nearing the end of a track, an end of track warning
indication can be shown on the display and a "21 EOM
TRACK TALLY" signal can be output from the CONTROL I/
O PARALLEL connector. With data CDs, an end of track
warning will not appear on the display. The CONTROL I/O
PARALLEL "21 EOM TRACK TALLY" signal will be output as
a pulse when the file playback ends.
32
TASCAM CD-6010
17
).
ON
By setting in advance the number of seconds before
the track end that the warning is shown, when playback
reaches that point, the "
" in the time display will begin
:
blinking. At the same time the CONTROL I/O PARALLEL
"21 EOM TRACK TALLY" signal will be output.
Use the
menu item to set the value from
10 EOM_T
among the following options.
Options:
,
,
,
,
,
OFF
0
5
10
15
20
For values other than
, the number indicates the
OFF
number of seconds before the end of the track that the
warning begins. However, when set to
be shown on the display when track playback ends, but
a "21 EOM TRACK TALLY" signal will be output from the
CONTROL I/O PARALLEL connector as a pulse.
At the default value, 30 seconds before the end of the
track, the "
" begins to blink and the CONTROL I/O
:
PARALLEL "21 EOM TRACK TALLY" signal is output
NOTE
The TRACK EOM function setting is retained even when the
power is turned off.
End of disc warning (Disc EOM)
You can set the unit to output a "23 EOM DISC TALLY"
signal from the CONTROL I/O PARALLEL connector when
nearing the end of a disc a few seconds before it ends.
Use the
menu item to set the time of the
06 EOM_D
EOM function.
Options:
,
,
,
,
,
OFF
0
5
10
15
20
For values other than
, the number indicates the
OFF
number of seconds before the end of the disc that the
warning begins. When set to
signal will be output from the CONTROL I/O PARALLEL
connector as a pulse when disc playback stops.
NOTE
The DISC EOM function setting is retained even when the
power is turned off.
F
M
S
,
,
(default value),
25
30
35
, no warning will
0
,
,
(default value),
25
30
35
, a "23 EOM DISC TALLY"
0
Advertisement
Table of Contents
