Tascam DP-32 Digital Portastudio Owner's Manual page 90

16 – Messages
Master Track
Too Large
MBR Error
Init CARD
No Card
No Armed Track
No Undo History
Not Stopped
Now Recording
OUT point must
be set after
the IN point.
Protected Card
Recorded Track
Not Found
Revert to
discard changes.
Same Track
Song Protected
Stereo Track Full
Track Full
Trk Edit Fail
Trk Too Short
Turn off the
Guitar Effect or
use two or less
Dynamic Effects.
Work Memory Full
90
TASCAM DP-32
The master file is too large.
You tried to create a master file that is larger than the remaining open space on the SD card.
To make more space, format the SD card (see "Quick formatting an SD card" on page 74 and "Full
formatting an SD card" on page 75), delete unnecessary files or connect the unit to a computer to
transfer (and then delete) files.
The formatting of the card is abnormal or corrupted.
Replace the card or format the card using the FORMAT menu.
Formatting erases all data currently on the card.
No SD card is in the unit. Load a recordable SD card.
There is no track in recording standby (armed).
You tried to enter auto punch mode or pressed the
standby. (See "Automatic punching in and out" on page 54.)
Put a track into recording standby before pressing
There is no undo history.
There are no actions to be undone. (See "Undoing an operation" on page 47.)
The recorder transport is not stopped.
When the recorder is not stopped, this message appears if you press a button, such as
that works only when the recorder is stopped.
The unit is recording.
This message appears when you try to operate a menu while the unit is recording.
Some other operations are also not allowed during recording.
You cannot set the OUT point before the IN point.
Set the OUT point after the IN point.
The inserted SD card is write-protected.
To record or edit, turn off the unit and unlock the write-protection on the SD card.
When trying to use the export function, no recordings were found on the current song's tracks.
No tracks have been recorded in the current song, or virtual tracks with recordings have not been
assigned to physical tracks.
Select a recorded song, assign the track you want to export to a physical track, and then export it. (See
"Virtual tracks" on page 56.)
Edits and changes made since the song was loaded will be cleared, and the song will be reset to status it
had when loaded. Proceed only when you are sure you wish to discard all changes.
The same track has been specified.
This message appears when using the clone track function if the source track is also set as the
destination track.
The song is protected.
You are trying to change (record, edit, etc.) a protected song. (See "Protecting songs" on page 38.)
Unprotect the song.
All the stereo tracks already have recordings.
This message appears if you try to import a stereo file when all the stereo tracks in the song already
have recordings, even if some mono tracks are still open.
All the tracks already have recordings.
This message appears if you try to import a file when all tracks in the song already have recordings. (See
"Importing tracks" on page 78.)
Track editing failed.
Save the song, turn the unit off and on again, and then try the track edit one more time.
The track is too short.
You are trying to record in mixdown mode, but the time between the IN and OUT points is too short.
The IN and OUT points must be at least 4 seconds apart. (See "Setting IN/OUT points" on page 53.)
While using a guitar effect, the use of dynamic effects is limited to one or two channels. To use dynamic
effects on three or more channels, turn the guitar effect OFF.
The working memory is full.
Even if the SD card has enough remaining space, this error could occur if you perform many editing
operations. You may be able to continue to work after executing the DELETE UNUSED item in the
SONG menu to increase the amount of available working memory. (See "Undoing an operation" on
page 47.)
RECORD
button when no tracks were in recording
RECORD
or activating auto punch.
UNDO/REDO
,