Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Tannoy Power Dual iQ 15
Summary of Contents for Tannoy Power Dual iQ 15
-
Page 1: User Manual
iQ SERIES USER MANUAL iQ 10/15... -
Page 3: Table Of Contents
CONTENTS Introduction Unpacking Connectors/Cabling Amplification & Power Handling Operation Equalisation Arraying Dimensions Rigging & Suspension General Safety Advice SECUR ET – VEB Eyebolt Suspension Truss Performance Data Technical Specifications System Configuration & OEM Controllers System Parameters Recommended Service Parts & Accessories Warranty Declaration of Conformity... -
Page 4: Introduction
Using a 250mm (10”) version of Tannoy’s own unique, point source and constant directivity PowerDual™ driver, the iQ 10/15 is a single cabinet full range system incorporating a 15”... -
Page 5: Amplification & Power Handling
Tannoy has adopted the following wiring standard for the iQ 10/15: - SPEAKON™ SIGNAL CONNECTOR Pin 1+ LF Positive Pin 1- LF Negative Pin 2+ MF/HF Positive Pin 2- MF/HF Negative For a worldwide list of Neutrik distributors see http://www.neutrik.com/... -
Page 6: Operation
5. Operation For optimal performance, the iQ 10/15 has been designed to operate in conjunction with the Tannoy TDX1 & TDX2 System Controllers, and iQ18B bass unit for extended bass performance. The TDX controllers have been factory preset to provide the recommended eq, crossover points, and overall system balance. -
Page 7: Dimensions
8. Dimensions 540.0 680.0 1116.0... -
Page 8: Rigging & Suspension
Rigging & Suspension General Safety Advice The Tannoy Professional hardware covered in this guide has been designed to offer quick, simple, cost effective and secure solutions for mounting specific Tannoy Professional loudspeakers. This hardware has been designed and manufactured with a high safety load factor for its specific role. -
Page 9: Secur Et - Veb Eyebolt
SECUR ET – VEB Eyebolt The Tannoy iQ 10/15 loudspeaker can be flown with high quality VEB M10 eyebolts with collar to BS4278:1984. The loudspeakers are equipped with internal steel braces, which also double as the flying points, and accept VEB M10 eyebolts. - Page 10 Suspension Truss The iQ Suspension Truss is a "semi-custom" product line that is built to order. Please contact your Tannoy or ATM Fly-Ware dealer with the loudspeaker model numbers along with the array application. Full assembly instructions for the iQ Suspension Truss accompany the product.
- Page 11 Typical Suspension Truss applications – 2 x iQ 10/15 2 x iQ 10C & 2 x iQ 10/15...
-
Page 12: Performance Data
Performance Data FREQUENCY RESPONSE Anechoic System Frequency Response, 1 watt (MF/HF) @ 1 metre on axis INPUT IMPEDANCE Impedance (Passive MF/HF only) - Page 13 High Frequency (Tri-amp option) Anechoic Frequency Response, 1 watt (HF) @ 1 metre on axis Impedance (HF only)
- Page 14 Anechoic Frequency Response, 1 watt (MF) @ 1 metre on axis Impedance (MF only) A comprehensive range of measurements including off axis frequency response curves, octave & third octave polar diagrams (single & two cabinet arrays) and beamwidth plots as well as Ease™ data can be downloaded from http://www.tannoy.com/...
-
Page 15: Technical Specifications
- or can be found in this IQ 10/15 user manual Tannoy operates a policy of continuous research and development. The introduction of new materials or manufacturing methods will always equal or exceed the publish which Tannoy reserves the right to alter without prior notice. -
Page 16: System Configuration & Oem Controllers
12. System Configurations & OEM Controllers Passive or Biamp? The iQ 10/15 is supplied as standard for bi-amp operation, therefore there is no internal passive crossover network between the LF & Mid/High units. The Bi-amp controller parameters below must be adhered to for optimum performance. An optional iQ 10/15 (tri-amp version) can be ordered. -
Page 17: Warranty
Warranty No maintenance of the iQ 10/15 loudspeaker is necessary. All Tannoy professional loudspeaker products are covered by a 5 year warranty from the date of manufacture subject to the absence of misuse, overload or accidental damage. Claims will not be considered is the serial number has been altered or removed. -
Page 18: Declaration Of Conformity
15. Declaration of Conformity The following apparatus is/are manufactured in the United Kingdom by Tannoy Ltd of Rosehall Industrial estate, Coatbridge, Scotland, ML5 4TF and conform(s) to the protection requirements of the European Electromagnetic Compatibility Standards and Directives relevant to Domestic Electrical Equipment. The apparatus is... - Page 20 Strathclyde, ML5 4TF, SCOTLAND Telephone: +44 (0) 1236 420199 Fax: +44 (0)1236 428230 Tannoy North America Inc, Suite 1. 335 Gage Avenue, Kitchener, Ontario, CANADA, N2M 5E1 Telephone: (519) 745 1158 Fax: (519) 745 2364 Issue 1.0 Part No. 6481 0430...