Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Tannoy in wall
Summary of Contents for Tannoy in wall
- Page 1 O W N E R ’ S M A N U A L...
-
Page 2: Stand Mounting Models
11-15 WARRANTY This equipment has been produced and tested with care and precision. All Tannoy speaker systems are built to give first class service and carry a 5-year warranty. Active subwoofers carry a 1-year warranty. If the equipment proves to be defective within this period for any reason other than accident, misuse, unauthorised modification or fair wear and tear, Tannoy will repair any such defect or, at our option, replace it without charge for parts, labour or return carriage. - Page 3 Consult the enclosed product specification sheet for the acceptable power range of amplifier matching. The high peak power handling of Tannoy loudspeakers permits responsible use with more powerful amplifiers - please read the Warranty. As with all loudspeaker systems, the power handling is a function of voice coil thermal capacity. Care should be taken to avoid overdriving any amplifier, as this will cause output overload resulting in 'clipping' or distortion within the output signal.
-
Page 4: Cable Choice
30kHz. Operating between the roll-off point of the exclusive Tannoy mid-bass or Dual Concentric™ drive units and 51kHz, the Tannoy WideBand™ high frequency unit will accurately reproduce the leading edge of individual notes allowing the listener to experience the entire bandwidth information of instruments. - Page 5 TERMINAL PANEL CONNECTIONS AND DRIVER EARTHING iw6 DS DISCRETE MODEL In this model there are two robust spring loaded terminals designed to take substantial high quality loudspeaker cable. Strip off approximately 8mm (1/4”) of the outer protective layer and twist the inner cores together. Depress the spring-loaded terminal and insert the core ensuring that correct polarity is maintained.
-
Page 6: Installation
There is a great deal of mounting location flexibility with both models when used in home cinema or multi channel systems. In particular, please note that due to the unique point source symmetrical dispersion properties of the Tannoy Dual Concentric™ drive unit, the model iw6TDC can be mounted in either portrait (in stud partition wall situations) or landscape positions where sufficient space exists behind the wall surface. - Page 7 Strip 8mm (1/4 inch) of shielding from the end of the speaker cables in preparation for connection to the spring terminals on the rear of speaker. Check that the clamping arms are aligned as shown prior to insertion in the wall. Connect the speaker cable observing the correct wiring polarity.
- Page 8 NOTE SPEAKER LOADING VOLUME There are two simple approaches to achieve a sealed ‘enclosure’ to provide the correct driver loading area behind the speaker. The chosen method will depend on whether the wall is under construction, as in a new building project, or an existing wall where access is limited. Option 1 Stud partition walls under construction, with 102mm by 51mm (4 by 2 inch) timber at 406mm (16 inch) centres.
-
Page 9: Technical Specifications
TECHNICAL SPECIFICATIONS iw6 DS | IN WALL DISCRETE iw6 TDC | IN WALL DUAL CONCENTRIC™ PERFORMANCE Recommended amplifier power 20-100 20-150 Watts RMS Continuous power handling Watts RMS Peak power handling - Watts Sensitivity (2.83 Volts @ 1m) 90dB 91dB... -
Page 10: Technical Drawings
TECHNICAL DRAWINGS iw6 DS DISCRETE MODEL 168.5 NEGATIVE (-) POSITIVE (+) 209.0 (BLACK TERMINAL) (RED TERMINAL) 271.5 320.0 93.0 REAR SIDE FRONT BOTTOM... - Page 11 iw6 TDC DUAL CONCENTRIC™ MODEL 168.5 'EARTH' OR 'GROUND' (GREEN TERMINAL) NEGATIVE (-) POSITIVE (+) 209.0 (BLACK TERMINAL) (RED TERMINAL) 271.5 320.0 99.0 FRONT SIDE REAR BOTTOM...
- Page 12 Tannoy United Kingdom T: +44 (0) 1236 420199 F: +44 (0) 1236 428230 E: enquiries@tannoy.com Tannoy North America T: (519) 745 1158 F: (519) 745 2364 E: inquiries@tannoyna.com...