Tannoy I6 AW User Manual

Tannoy I6 AW User Manual

Power speakers
Hide thumbs Also See for I6 AW:

Advertisement

i6 AW & i6T AW
USER MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the I6 AW and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Tannoy I6 AW

  • Page 1 AW & i6T AW USER MANUAL...
  • Page 2: Table Of Contents

    CONTENTS 1. Introduction 2. Unpacking 3. Connectors/Cabling 4. Polarity Checking 5. Amplification & Power Handling 6. Power Selection 7. Equalisation 8. Dimensions 9. Hardware 10. Performance Data 11. Technical Specifications 12. Troubleshooting Guide 13. i6 Recommended Service Parts & Accessories 14.
  • Page 3: Introduction

    Able to deliver consistent performance under a wide range of adverse conditions the i6 AW is suited to applications indoors or out, whether it be a theme bar or theme park. Available in dark grey or white the i6 AW will effectively blend into most backgrounds.
  • Page 4: Polarity Checking

    CABLE RUN C.S.A. OF EACH CONDUCTOR (mm) 4. Polarity Checking It is most important to check the polarity of the wiring. A simple method of doing this without a pulse based polarity checker for LF units is as follows: Connect two wires to the +ve and -ve terminals of a PP3 battery.
  • Page 5: Power Selection

    6. Power Selection (i6T AW) Determine the maximum power in watts needed at each speaker location. The i6 AW transformer can be tapped at 30w, 15w, 7.5w, & 3.75w via the rotary switch located on the metal plate at rear of the loudspeaker. When the relevant tappings have been selected add the individual wattages required at all speakers and select an amplifier with a rating equal to or exceeding the total wattage required.
  • Page 6: Hardware

    9. Hardware The i6AW can be wall or ceiling mounted using the MB6 (optional) bracket (fig 1.) which is designed to offer the maximum flexibility in selecting the desired angles. The MB6 is supplied with M8 bolts for fixing to the loudspeaker (fig1.& 2). After fixing the bracket to the wall or ceiling remove the plastic plugs from the top and bottom of the loudspeaker.
  • Page 7: Performance Data

    10. Performance Data Anechoic Frequency Response, 1watt @ 1m Impedance...
  • Page 8 ---- Hororizontal Vertical 500Hz...
  • Page 9: Technical Specifications

    11. Technical Specifications Frequency response (1) +/- 3dB Recommended Amplifier Power Power Handling Sensitivity (1) 2.83 volt @ 1m Maximum SPL (3) @ 1m Maximum SPL (3) With THP30 Transformer @ 1m Transformer (i6T AW) Impedance DI Averaged (PCQ) @ 1kHz (ISO) @ 2kHz (ISO) @ 4kHz (ISO) @ 8kHz (ISO)
  • Page 10: Troubleshooting Guide

    12. Troubleshooting Guide Symptom No Output From Speakers Intermittent Output Poor Low Frequency Output Irregular sounds such as buzzing and humming emanating from the loudspeaker Possible Cause Broken Speaker Cables(s) Amplifier Poor Connection “Out of phase” connection Poor system grounding Faulty electronic device in the signal chain Action...
  • Page 11: Warranty

    7300 0684 8000 0920 14. Warranty No maintenance of the i6 AW loudspeaker is necessary. All Tannoy professional loudspeaker products are covered by a 5 year warranty from the date of manufacture subject to the absence of misuse, overload or accidental damage.
  • Page 12: Declaration Of Conformity

    Declaration of Conformity The following apparatus is/are manufactured in the United Kingdom by Tannoy Ltd of Rosehall Industrial estate, Coatbridge, Scotland, ML5 4TF and conform(s) to the protection requirements of the European Electromagnetic Compatibility Standards and Directives relevant to Domestic Electrical Equipment. The apparatus is designed and constructed such that electromagnetic disturbances generated do not exceed levels allowing radio and telecommunications equipment and other apparatus to operate as intended, and, the apparatus has an adequate level of intrinsic immunity...

This manual is also suitable for:

I6t aw

Table of Contents