Page 1 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Copyright E 2000 Ford Motor Company Contents...
Page 2: Introduction
Introduction ICONS Indicates a safety alert. Read the following section on Warnings. Indicates that vehicle information related to recycling and other environmental concerns will follow. Correct vehicle usage and the authorized disposal of waste, cleaning and lubrication materials are significant steps towards protecting the environment.
Page 3 1 600 km (1 000 miles). INFORMATION ABOUT THIS GUIDE The information found in this guide was in effect at the time of printing. Ford may change the contents without notice and without incurring obligation.
Page 4 Introduction Vehicle symbol glossary These are some of the symbols you may have on your vehicle. Safety Alert Fasten Safety Belt Airbag - Side Child Seat Installation Warning Brake System Brake Fluid - Non Petroleum Based Master Lighting Switch Fog Lamps - Front Fuel Pump Reset Windshield Defrost/Demist...
Page 5 Vehicle symbol glossary Child Safety Door Lock/Unlock Engine Oil Engine Coolant Temperature Battery Battery Acid Fan Warning Maintain Correct Fluid Level Engine Air Filter Jack Introduction Panic Alarm Engine Coolant Do Not Open When Hot Avoid Smoking, Flames, or Sparks Explosive Gas Power Steering Fluid Emission System...
Page 6: Instrumentation
Instrumentation Page 19-20 Headlamp control Page 21 Panel dimmer control Page 159-167 Fuse panel Page 21 Luggage compartment control Page 20, 54 Direction indicators/ high beam Page 56-59 Speed control Page 54 Steering wheel adjustment Page 8-18 Instrument cluster Page 55 Wiper lever Page 53 Ignition switch...
Page 7 Page 32 Hazard flasher Instrumentation Page 73 Anti theft system control light Page 33-53 Electronic sound system Page 24-31 Climate controls Page 32 Rear window defrost control Page 30 Air conditioning/ Recirculated air control...
Page 8 Instrumentation INSTRUMENT CLUSTER WARNING LIGHTS AND CHIMES Check engine Your vehicle is equipped with a computer that monitors the engine's emission control system. This system is commonly known as the On Board Diagnostics System (OBD II). This OBD II system protects the environment by ensuring that your vehicle continues to meet government...
Page 9 The Check engine indicator light illuminates when the ignition is first turned to the ON position to check the bulb. If it comes on after the engine is started, one of the engine's emission control systems may be malfunctioning. The light may illuminate without a driveability concern being noted.
Page 10 Instrumentation If the Check engine light remains on, have your vehicle serviced at the first available opportunity. Light is blinking: Engine misfire is occurring which could damage your catalytic converter. You should drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced at the first available opportunity.
Page 11 Instrumentation Air bag readiness Momentarily illuminates when the ignition is turned on. If the light fails to illuminate, continues to flash or remains on, have the system serviced immediately. Doors ajar Illuminates when the ignition is in the ON or START position and any door or the luggage compartment is open.
Page 12 Instrumentation Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter. Charging system Illuminates when the ignition is turned to the ON position and the engine is off.
Page 13 Instrumentation Brake system warning Momentarily illuminates when the ignition is turned to the ON position and the engine is off. If brake warning lamp does not illuminate at this time, seek service immediately. Also illuminates when the parking brake is engaged. Illumination after releasing the parking brake indicates low brake fluid level or ABS (if equipped)
Page 14 Instrumentation Speed control (if equipped) Illuminates when the speed control system is switched on. Refer to Speed control in the Controls and features chapter. Upshift (if equipped) Illuminates when it is best to shift to the next highest manual transaxle gear for the maximum fuel economy.
Page 15 Instrumentation Headlamps on warning chime Sounds when the headlamps or parking lamps are on, the ignition is off (and the key is not in the ignition) and the driver's door is opened. Safety belt warning chime Chimes to remind you to fasten your safety belts.
Page 16 Instrumentation INSTRUMENT CLUSTER GAUGES Temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area. If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool.
Page 17 This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level the gauge indication will not be accurate. If the gauge enters the red section and the multi function warning light illuminates, refer to What you should know about fail safe cooling in the Maintenance and...
Page 18 Instrumentation Speedometer Indicates the current vehicle speed. Odometer Registers the total kilometers (miles) of the vehicle. Tripmeter Registers the kilometers (miles) of Tripmeter individual journeys. To reset Odometer depress the control. Reset control Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position).
Page 19: Controls And Features
HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. Fog lights (if equipped) Switch on the headlamps and pull out the control switch one position.
Page 20 Controls and features The control light will illuminate when the fog lights are in use. The fog lights should be used only when visibility is considerably restricted by fog, snow or rain. Daytime running lights (DRL) (if equipped) Turns the headlamps on. To activate: The engine must be running and The headlamp control is in the...
Page 21 Controls and features PANEL DIMMER CONTROL This can be adjusted to vary the intensity of the panel lighting. Operates only when the exterior lights are switched on. REMOTE LUGGAGE COMPARTMENT RELEASE (if equipped) To open the luggage compartment, press the control. The control does not function if the vehicle is traveling faster than 7 km/h (4 mph).
Page 22 Controls and features To open the luggage compartment door (lid) from the inside, pull the illuminated T" shaped handle and push open the door (lid). The material the handle is made of will glow in the darkness of the luggage compartment following a brief exposure to ambient light.
Page 23 On hot days, the temperature in the trunk can rise very quickly and cause injury or death to any living thing (animal, small child) entrapped in the trunk. Sedans may be equipped with glow in the dark unlocking controls, which allow a means of escape by exiting through the folding rear seatback.
Page 24 Controls and features CLIMATE CONTROLS Heater only system Fan speed control Controls the volume of air circulated in the vehicle. Temperature control Controls the temperature of the airflow inside the vehicle. The air cannot be cooled below the outside temperature. Mode selector control Controls the direction of the airflow to the inside of the vehicle.
Page 25 (Panel) Distributes outside air through the instrument panel registers. (Panel and Floor) Distributes outside air through the instrument panel registers and the floor ducts. (Floor) Allows for maximum heating. Distributes outside air through the floor ducts. (Floor and defrost) Distributes outside air through the windshield defroster ducts and the floor ducts.
Page 26 Controls and features Operating Tips In humid weather, select (Defrost) before driving. This will help to reduce fogging on your windshield. After a few minutes, select any desired position. Do not put objects under the front seat that will interfere with airflow to the back seats.
Page 27 Controls and features Manual heating and air conditioning system (if equipped) Fan speed control Controls the volume of air circulated in the vehicle. Temperature control Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle.
Page 28 Controls and features The air conditioning functions in all modes if the outside temperature is 4 C (40 F) or higher. Since the air conditioner removes considerable moisture from the air during operation, it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the...
Page 29 Controls and features (Floor and defrost) Distributes air through the windshield defroster ducts and the floor ducts. Heating and air conditioning capabilities are provided in this mode. For added customer comfort, when the temperature control knob is anywhere in between the full hot and full cold positions, the air distributed through the floor ducts will be slightly warmer than the air...
Page 30 Controls and features Air conditioning control (if equipped) Press the control to turn on or off. The control light in the switch indicates operation. This mode can be used for air conditioning. It will only function if the temperature is about 4 C (40 F) or higher.
Page 31 Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield under the hood). If the vehicle has been parked with the windows closed during hot weather, the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open.
Page 32 Controls and features REAR WINDOW DEFROSTER The rear window defroster control is located on the instrument panel. Press the defroster control to clear the rear window of thin ice and fog. The small LED will illuminate when the defroster is activated. The defroster turns off automatically after 14 minutes or when the ignition is turned to the...
Page 33 Controls and features AUDIO SYSTEM Anti-theft protection panel To deter would be thieves, Ford audio units have a removable front panel without which the unit will not work. Avoid touching the contacts on the back of the panel and do not use excessive force to refit it.
Page 34 Controls and features Replacement panels Your Ford Dealer will require the following if you need to order a replacement panel: 1. Your name and address. 2. The Vehicle Identification Number (visible on a plate mounted on the instrument panel). Refer to illustration under Vehicle...
Page 35 Radio reception To gain the best reception, always tune to the strongest station signal available. The following tips will help you gain the best reception from your Ford audio system. AM reception Under most conditions, strong signals provide stable sound quality and little signal disturbance.
Page 36 Controls and features 4100N AUDIO CONTROLS On/Off and volume control Station preset buttons Sound adjustment SEEK/tuning control control Clock control Manual tuning control Waveband selection...
Page 37 On/Off Press for on or off. Volume control The display indicates the level selected. Sound adjustments Press to select between bass, treble, fade and balance sound adjustments. Bass Press as necessary to select bass. Use the volume control to make adjustments. Treble Press as necessary to select...
Page 38 Controls and features Waveband selector (AM/FM) Seek/tuning control (SEEK) " Manual tuning control (TUNE) " Station presets Stereo indicator Clock (CLK)
Page 39 4500N AND 4600N AUDIO CONTROLS The 4500 radio/cassette is compatible with a CD changer. Automatic music search Bass/ Treble control On/Off and Volume control Anti theft protection panel release button Controls and features Fade/Balance control Scan Clock tuning Station preset buttons Anti theft protection panel...
Page 40 Controls and features The 4600 radio/ CD player is compatible with a CD changer. CD eject Bass/Treble control On/Off and Volume control Anti theft protection panel release button Fade/Balance control Scan Clock tuning Station preset buttons Anti theft protection panel CD control Waveband/ AutoStore...
Page 41 Controls and features On/off Press for on/off. This button can also operate the radio for up to one hour with the ignition turned off. The radio automatically switches off after one hour. This function can be used repeatedly. Volume control The display indicates the level selected.
Page 42 Controls and features Fade/Balance control Press FADE/BAL" once for fade (front to rear) or twice for balance (left to right), and use the volume control for sound system adjustment. The display indicates the level selected. To adjust beyond the 0" setting, stop rotating the control at 0"...
Page 43 Waveband selector (AM/FM) Press repeatedly during radio reception to select AM, FM1, FM2 or AutoStore (see AutoStore selector). The display indicates the selection made. Press during tape or CD playback to return to radio reception. AutoStore selector AutoStore selects six strong FM station signals and stores them on the preset buttons.
Page 44 Controls and features Station preset buttons Select a waveband (FM or AM) and tune to the station required. Press and hold one of the preset buttons. When sound returns, the station has been stored. 24 preset frequencies can be stored - six on each of the AM, FM1, FM2 and AutoStore bands.
Page 45 Controls and features MENU button (main features) – radio Manual tuning Automatic V olume Control (AVC)
Page 46 Controls and features 4500N Units only Tape control buttons Insert a tape and playback will automatically override radio or CD. TAPE A" or TAPE B" appears in the display to indicate which side of the tape is playing. Note that the tape side facing upward in the audio unit is always considered TAPE A".
Page 47 Controls and features buttons fully It is also recommended that the tape head in the audio unit is cleaned regularly with a wet cleaning cassette, which is available from your Ford Dealer.
Page 48 Controls and features MENU button (main features) – tape Dolby B r noise reduction Automatic V olume Control (AVC)
Page 49 Controls and features 4600N units only CD Playback Track selection "...
Page 50 Controls and features Fast forward/reverse Press and hold SEEK or SEEK " to search backwards or forwards across the tracks on the disc. Scan mode Press the SCAN button. Each track is played in turn for a short period. During this scan, SCAN" appears in the display.
Page 51 CD care and maintenance For best possible sound quality, use CDs that are clean and in good condition. CD error codes Codes may be shown in the audio unit display that indicate errors with the CD unit. These codes are as follows: Display Description/rectification...
Page 52 Controls and features Random track playback (SHUF) Track compression (COMP) Automatic V olume Control...
Page 53 Controls and features POSITIONS OF THE IGNITION Note:...
Page 54 Controls and features TILT AND TELESCOPE STEERING (if equipped) Never adjust the steering wheel while the vehicle is moving. Pull the locking lever down to adjust the steering column position. Return the lever to its original position to secure the wheel from sliding".
Page 55 Controls and features WINDSHIELD WIPER/WASHER CONTROL Move the lever down for a single wipe. For intermittent operation, move the lever up one position and adjust the rotary switch to the desired speed. For normal operation, move the lever up two positions. For high speed operation, move the lever up three positions.
Page 56 Controls and features SPEED CONTROL (if equipped) To turn speed control on Press ON. Vehicle speed cannot be controlled until the vehicle is travelling at or above 48 km/h (30 mph). Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved.
Page 57 Controls and features To set a speed...
Page 58 Controls and features To set a higher speed Press and hold SET ACC. Release the control when the desired vehicle speed is reached, or press and release SET ACC. Each press will increase the set speed by 1.6 km/h (1 mph) or accelerate with your accelerator pedal.
Page 59 To disengage speed control Depress the brake pedal or depress the clutch pedal (if equipped). Disengaging the speed control will not erase the previously programmed set speed. To return to a set speed Press RES. For RES to operate, the vehicle speed must be faster than 48 km/h (30 mph).
Page 60 Controls and features DOME LAMPS The dome lamp equipped with a control switch will illuminate when: the doors are closed and the switch is in the on position. the switch is in the door activated position and any door is open. When the dome lamp switch is in the off position, it will not illuminate when you open the...
Page 61 POWER WINDOWS (if equipped) Press and hold the rocker switches to open and close the windows. Press the top portion of the rocker switch to close. Press the bottom portion of the rocker switch to open. One touch down To make the driver window open fully without holding the window control, momentarily press the driver window control completely...
Page 62 Controls and features POWER SIDE VIEW MIRRORS The control can be swiveled and turned. Turn the control counterclockwise to adjust the driver's side mirror, clockwise to adjust the passenger's side mirror. Adjust the selected mirror by moving the center control in the desired direction.
Page 63 Controls and features LUGGAGE COVER Coupe Detach the lifting straps on the liftgate. Release the cover at the sides and pull it out horizontally without tilting it. Replace in reverse order. Make sure the cover is properly aligned when inserting it. Wagon Pull out the roller cover and secure the retaining points.
Page 64 Controls and features POSITIVE RETENTION FLOOR MAT (if equipped) Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the break pedal.
Page 65 Controls and features Unlocking the doors Press this control to unlock the driver door and disarm the anti theft system (if equipped). The interior lamps will illuminate. Press the control again within three seconds to unlock all doors. Locking the doors Press this control to lock all doors.
Page 66 Controls and features Opening the luggage compartment Press the control once or twice (depending on when the vehicle was built) to open the luggage compartment. Be certain the luggage compartment is closed before driving your vehicle. The luggage compartment may appear closed, but it may not be latched.
Page 67 Controls and features Illuminated entry Replacing the battery...
Page 68 Controls and features 2. Place the positive (+) side of new battery in the same orientation. Refer to the diagram inside the transmitter unit. 3. Snap the two halves back together. Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle.
Page 69 Controls and features 2. Turn the ignition lock from OFF (2) to ON (3) at least 4 times in 6 seconds. 3. Switch off the ignition. Now the control module has entered the learning mode" for 10 seconds. This mode is indicated by a chime.
Page 70 Controls and features PERIMETER ALARM SYSTEM (if equipped) The perimeter anti theft system will help prevent your vehicle from unauthorized entry. Arming the system When armed, the perimeter alarm will help protect your vehicle from unauthorized entry. When unauthorized entry occurs, the system will flash the hazard flashers and will sound the horn.
Page 71 Controls and features SECURILOCKT PASSIVE ANTI-THEFT SYSTEM Your vehicle is equipped with a coded key anti theft system. Only the correct key will be able to start your vehicle. If your keys are lost or stolen, you must take your vehicle to your dealership for key reprogramming.
Page 72 Controls and features The SecuriLockT passive anti theft system is not compatible with aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Large metallic objects or devices such as the Mobil SpeedpassT on the same key ring as your SecuriLockT key may cause vehicle starting...
Page 73 Controls and features Theft indicator When the ignition is turned to ON or START, the theft indicator on the instrument panel will light for three seconds and then go out (indicates proper SecuriLockT system operation). If the key is in the ignition and the theft indicator stays on for an extended period of time or flashes rapidly, have the...
Page 74 Controls and features Procedure to program spare SecuriLockT keys New SecuriLockT keys must have the correct mechanical key cut for your vehicle. Conventional (non SecuriLockT) keys cannot be programmed to your vehicle. The correct type of SecuriLockT key for your vehicle is identifiable by the alphanumeric characters stamped on the key blade.
Page 75 Controls and features 1. Insert the first previously programmed SecuriLockT key into the ignition and turn the ignition from OFF (2) to ON (3) (maintain ignition in ON for at least one second). 2. Turn ignition to OFF and remove the first SecuriLockT key from the ignition.
Page 76 Controls and features If the programming procedure was successful, the new SecuriLockT key(s) will start the vehicle's engine. The theft indicator (located on the instrument panel) will light for three seconds and then go out. If the programming procedure was not successful, the new SecuriLockT key(s) will not operate the vehicle's engine.
Page 77: Seating And Safety Restraints
SEATING Never adjust the driver's seat or seatback when the vehicle is moving. Adjustable head restraints Your vehicle is equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to limit head motion in the event of a rear collision.
Page 78 Seating and safety restraints Turn the handle to adjust the height of the seat. Lift the control to adjust the angle of the seatback. Folding the seat forward (Coupe) Pull the control and fold the seatback forward. Fold back the seatback until it locks with a distinct click".
Page 79 Seating and safety restraints Folding the rear seat cushion forward Lift the seat cushion and pull it forward. When returning the seats back to their original positions, make sure the safety restraints will function properly and are positioned in front of the seat back.
Page 80 Seating and safety restraints Returning the rear seatback to an upright position Fold back the seatback until it locks with a distinct click". Do not place any objects behind the seat which could prevent the seat from locking. Make sure the safety restraints will function properly and are positioned in front of the seatback.
Page 81 SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. To prevent the risk of injury, make sure children sit where they can be properly restrained. Always transport children 12 years old and under in the back seat and always use appropriate child restraints.
Page 82 Seating and safety restraints It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Page 83 2. To unfasten, push the release button and remove the tongue from the buckle. The front outboard and rear safety restraints in the vehicle are combination lap and shoulder belts. The front and rear seat passenger safety belts have two types of locking modes described below: Energy Management Feature This seat belt system has a...
Page 84 Seating and safety restraints Vehicle sensitive mode...
Page 85 Seating and safety restraints Safety belt pretensioner Your vehicle is equipped with safety belt pretensioners at the driver and front passenger seating positions. The safety belt pretensioner is a device which removes excess webbing from the safety belt system. The safety belt pretensioner uses the same crash sensor system as the front air bag supplemental restraint system...
Page 86 Seating and safety restraints When to use the automatic locking mode When a tight lap/shoulder fit is desired. Anytime a child safety seat is installed in a passenger front or outboard rear seating position (if equipped). Refer to Safety restraints for children or Safety seats for children later in this chapter.
Page 87 Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button and slide the height control down.
Page 88 Seating and safety restraints Safety belt warning light and warning chime Illuminates in the instrument cluster and a chime sounds to remind the driver to fasten his or her safety belt. Conditions of operation If... If the driver's safety belt is not buckled before the ignition switch is turned to the ON position ...
Page 89 Belt Minder (if equipped) The Belt Minder feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders to the driver that the driver's safety belt is unbuckled by intermittently sounding a chime and illuminating the Safety belt warning light in the instrument cluster.
Page 90 3 of 4 fatal crashes occur within 25 miles of home. Ford designs its safety belts to enhance comfort. If you are uncomfortable try different positions for the safety belt upper anchorage and seatback which should be as upright as possible;...
Page 91 Seating and safety restraints Reasons given... Consider... people ejected are 40 times more likely to DIE.
Page 92 Seating and safety restraints Do not sit on top of a buckled safety belt to avoid the Belt Minder chime. Sitting on the safety belt will increase the risk of injury in an accident. To disable (one time) or deactivate the Belt Minder feature please follow the directions stated below.
Page 93 Seating and safety restraints Safety belt Safety belt warning light...
Page 94 Seating and safety restraints 6. Within seven seconds of the Safety belt warning light turning off, buckle then unbuckle the safety belt. This will disable Belt Minder if it is currently enabled, or enable Belt Minder if it is currently disabled. 7.
Page 95 Seating and safety restraints Safety belt extension assembly If the safety belt is too short, even when fully extended, 20 cm (8 inches) can be added to the safety belt assembly by adding a safety belt extension assembly (part number 611C22). Safety belt extension assemblies can be obtained from your dealer at no cost.
Page 96 (if equipped), child safety seat tether bracket assemblies (if equipped), and attaching hardware, should be inspected after a collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision...
Page 97 AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly or gently and the risk of injury from a deploying air bag is the greatest close to the trim covering the air...
Page 98 Seating and safety restraints...
Page 99 Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating positions.
Page 100 Seating and safety restraints The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system. Rather, it means the forces were not of the type sufficient to cause activation. The front air bags are designed to inflate in frontal and near frontal collisions, not rollover, side impact, or rear...
Page 101 While the system is designed to help reduce serious injuries, it may also cause minor burns, abrasions, swelling or temporary hearing loss. Because air bags must inflate rapidly and with considerable force, there is the risk of death or serious injuries such as fractures, facial and eye injuries or internal injuries, particularly to occupants who are...
Page 102 Seating and safety restraints The SRS consists of: driver and passenger air bag modules (which include the inflators and air bags). side air bags (if equipped). Refer to Side air bag system later in this chapter. one or more impact and safing sensors.
Page 103 A difficulty with the system is indicated by one or more of the following: The readiness light will either flash or stay lit. The readiness light will not illuminate immediately after ignition is turned on. A series of five beeps will be heard.
Page 104 Seating and safety restraints Do not attempt to service, repair, or modify the air bag Supplemental Restraint System or its fuses. See your Ford or Lincoln Mercury dealer. All occupants of the vehicle including the driver should always wear their safety belts even when an air bag SRS is provided.
Page 105 The side air bags are fitted on the outboard side of the seatbacks of the front seats. In certain lateral collisions, the air bag on the side affected by the collision will be inflated, even if the respective seat is not occupied. The air bag was designed to inflate between the door panel and occupant to further enhance the protection provided...
Page 106 Seating and safety restraints If the side air bag has deployed, the air bag will not function again. The side air bag system (including the seat) must be inspected and serviced by a qualified technician in accordance with the vehicle service manual. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Page 107 Seating and safety restraints If either of these indications occurs, even intermittently, have the SRS serviced at your dealership or by a qualified technician immediately. Unless serviced, the system may not function properly in the event of a collision. Disposal of air bags and air bag equipped vehicles For disposal of air bags or air bag equipped vehicles, see your local...
Page 108 Seating and safety restraints Important child restraint precautions You are required by law to use safety restraints for children in the U.S. and Canada. If small children ride in your vehicle (generally children who are four years old or younger and who weigh 18 kg [40 lbs] or less), you must put them in safety seats made especially for children.
Page 109 Children and safety belts If the child is the proper size, restrain the child in a safety seat. Children who are too large for child safety seats (as specified by the child safety seat manufacturer) should always wear safety belts. Follow all the important safety restraints and air bag precautions that apply to adult passengers in...
Page 110 Seating and safety restraints To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards.
Page 111 SAFETY BELTS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer's instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision.
Page 112 Using automatic locking mode (passenger side front and outboard rear seating positions) (if equipped). Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
Page 113 Installing child safety seats in combination lap and shoulder belt seat positions 1. Position the child safety seat in a seat with a combination lap and shoulder belt. NEVER place a rear facing child seat in front of an active air bag. Air bags can kill or injure a child in a child seat.
Page 114 Seating and safety restraints 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer's instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) for that seating...
Page 115 Seating and safety restraints 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buckle and pull up on the shoulder belt while pushing down with your knee on the child seat.
Page 116 Seating and safety restraints Attaching child safety seats with ISOFIX attachments Some child seat manufacturers make safety seats that are labeled as ISOFIX or ISOFIX compatible child seats. These seats include two rigid or webbing mounted attachments that connect to two ISOFIX anchors at specific seating positions in your vehicle.
Page 117 The ISOFIX anchors are located on the rear section of the seat cushion, and at the bottom of the seatback. Follow the child seat manufacturer's instructions to properly install safety seats with ISOFIX or ISOFIX compatible attachments. Attach the ISOFIX or ISOFIX compatible child seat only to the appropriate locations shown.
Page 118 Seating and safety restraints Attaching child safety seats with tether straps Most new forward facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. Tether straps are available as an accessory for many older safety seats.
Page 119 Seating and safety restraints 2. Route the child safety seat tether strap over the back of the seat. On coupes, the removable package tray must be removed prior to attaching the tether strap to the tether anchor. On wagons, it may be necessary to remove the cargo cover assembly prior to attaching the tether strap to the tether anchor.
Page 120 Seating and safety restraints 5. Clip the tether strap to the anchor as shown. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 6. Refer to the Installing child safety seats in combination lap and shoulder belt seating positions section of this chapter...
Page 121 PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel injected engine, avoid pressing the accelerator before or during starting.
Page 122 Starting Do not start your vehicle in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions. If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle...
Page 123 Before starting the vehicle: 1. Make sure all vehicle occupants have buckled their safety belts. For more information on safety belts and their proper usage, refer to the Seating and safety restraints chapter. 2. Make sure the headlamps and vehicle accessories are off. If starting a vehicle with an automatic transaxle: Make sure the parking brake is...
Page 124 Starting Make sure the corresponding lights (if equipped) illuminate briefly. If a light fails to illuminate, have the vehicle serviced. If the driver's safety belt is fastened the light will not illuminate. STARTING THE ENGINE 1. Turn the key to 4 (START) without pressing the accelerator pedal and release as soon as the engine starts.
Page 125 Starting 2. If the temperature is above -12ºC (10ºF) and the engine does not start within five seconds on the first try, turn the key to OFF, wait ten seconds and try again. 3. If the temperature is below -12ºC (10ºF) and the engine does not start in fifteen seconds on the first try, turn the key to OFF and wait ten seconds and try again.
Page 126 Starting To prevent electrical shock, do not use your heater with ungrounded electrical systems or two pronged (cheater) adapters. Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer...
Page 127 Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer, and birth defects or other reproductive harm. Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch).
Page 128: Driving
Driving BRAKES Your service brakes are self adjusting. Refer to the Scheduled Maintenance Guide" for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle's brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Page 129 Driving Anti-lock brake system (ABS) (if equipped) On vehicles equipped with an anti lock braking system (ABS), a noise from the hydraulic pump motor and pulsation in the pedal may be observed during ABS braking events. Rapid pedal pulsation coupled with noise while braking under panic conditions or on loose gravel, bumps, wet or snowy roads is normal and...
Page 130 Driving ABS warning lamp (if equipped) The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned on and the engine is off. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced.
Page 131 Using ABS (if equipped) In an emergency or when maximum efficiency from the ABS is required, apply continuous full force on the brake. The ABS will be activated immediately, thus allowing you to retain full steering control of your vehicle and, providing there is sufficient space, will enable you to avoid obstacles and bring the vehicle to a...
Page 132 Driving Parking brake Apply the parking brake whenever the vehicle is parked. To set the parking brake, pull the handle up as far as possible. The brake warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released.
Page 133 Push the button on the end of the parking brake and push the handle down as fas as possible to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy.
Page 134 Driving If the steering wanders or pulls, the condition could be caused by any of the following: underinflated tire(s) on any wheel(s) high crosswinds wheels out of alignment loose or worn components in steering linkage. AUTOMATIC TRANSAXLE OPERATION (if equipped) Brake-shift interlock This vehicle is equipped with a brake shift interlock feature that...
Page 135 If it is necessary to use the above procedure to move the gearshift, it is possible that a fuse has blown or the vehicle's brakelamps are not operating properly. Refer to Fuses and relays in the Roadside emergencies chapter. Do not drive your vehicle until you verify that the brakelamps are working.
Page 136 Driving Driving with automatic transaxle (if equipped) Understanding gearshift positions Depress the locking button and move the automatic gearshift to the desired position. Hold the brake pedal down while you move the gearshift lever from P (Park) to another position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone.
Page 137 Never leave your vehicle unattended while it is running. R (Reverse) With the gearshift in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse) N (Neutral) With the gearshift in N (Neutral), the vehicle can be started and is free to roll.
Page 138 Driving D (Overdrive) The normal driving position for the best fuel economy. Transaxle operates in gears One through Four. D (Overdrive) can be deactivated by pressing the transaxle control switch on the gearshift lever. The O/D OFF light will illuminate on the instrument cluster.
Page 139 Driving To return to D (Overdrive) mode, press the transaxle control switch and the O/D OFF light will no longer be illuminated. Each time the vehicle is started, the transaxle will automatically return to normal overdrive mode. 2 (Second) Use 2 (Second) to start up on slippery roads or to provide additional engine braking on downgrades.
Page 140 Driving Manual transaxle operation (if equipped) Using the clutch Vehicles equipped with a manual transaxle have a starter interlock that prevents cranking the engine unless the clutch pedal is fully depressed. When starting a vehicle with a manual transaxle, you must: 1.
Page 141 Do not drive with your foot resting on the clutch pedal and do not use the clutch to hold your vehicle at a standstill while waiting on a hill. These actions will seriously reduce clutch life. Recommended shift speeds Upshift and downshift according to the following charts for your specific engine/drivetrain combination:...
Page 142 Driving Parking your vehicle 1. Apply brake and shift into N (Neutral). 2. Set parking brake. 3. Shift into 1 (First). 4. Turn ignition to position 2 (OFF). Do not park your vehicle in Neutral, it may move unexpectedly and injure someone.
Page 143 Type A transaxle (with SPI engine) You shift into R (Reverse) only by moving the gearshift fully to the right against a spring pressure and then rearward into R (Reverse) gear. Type B transaxle (with Zetec engine) To select reverse gear, lift the locking ring (1) and then move the gearshift fully to the right and rearward into R (Reverse) gear (2).
Page 144 Driving VEHICLE LOADING Before loading your vehicle, familiarize yourself with these terms. Base curb weight: Weight of the vehicle including any standard equipment, fluids, lubricants, etc. It does not include passengers or aftermarket equipment. Payload: Combined maximum allowable weight of cargo, passengers and optional equipment.
Page 145 GAWR (Gross Axle Weight Rating): Carrying capacity for each axle system. The GAWR is specific to each vehicle and is listed on the Safety Compliance Certification Label on the driver's door pillar. GCWR (Gross Combined Weight Rating): Maximum combined weight of towing vehicle (including passengers and cargo) and the trailer.
Page 146 Driving Trailer Weight Range: Specified weight range that the trailer must fall within that ranges from zero to the maximum trailer weight rating. Remember to figure in the tongue load of your loaded trailer when figuring the total weight. Do not exceed the GVWR or the GAWR specified on the Safety Compliance Certification Label.
Page 147 Driving If you are adding weight to the front of your vehicle (potentially including weight added to the cab), the weight added should not exceed the Front Axle Reserve Capacity (FARC). Additional frontal weight may be added to the front axle reserve capacity provided you limit your payload in other ways (i.
Page 148 Driving TRAILER TOWING Towing class Maximum gross trailer weight Maximum tongue load Engine Hitch design...
Page 149 Driving...
Page 150 Driving Preparing to tow Use the proper equipment for towing a trailer, and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance. Hitches Do not use hitches that clamp onto the vehicle bumper.
Page 151 Do not connect a trailer's lighting system directly to your vehicle's lighting system. To get the proper equipment for hooking up your trailer's lamps, see your Ford dealer. Be sure to follow their instructions carefully. If you do not install trailer lights...
Page 152 Driving When towing a trailer: Shift out of D (Overdrive) and into 2 (Second) or a lower gear when towing up or down steep hills. This will eliminate excessive downshifting and upshifting for optimum fuel economy and transaxle cooling. Anticipate stops and brake gradually.
Page 153 Allow more distance for stopping with a trailer attached. The trailer tongue weight should be 10-15% of the loaded trailer weight. After you have traveled 80 km (50 miles), thoroughly check your hitch, electrical connections and trailer wheel lug nuts. When stopped in traffic for long periods of time in hot weather, place the gearshift in P (Park) and...
Page 154 Driving Recreational towing Follow these guidelines for your specific powertrain combination to tow your vehicle with all four wheels on the ground (such as behind a recreational vehicle). These guidelines are designed to ensure that your transmission is not damaged due to insufficient lubrication.
Page 155 Driving LUGGAGE RACK (if equipped) The maximum load is 100 kg (220 lb) on the luggage rack structure. The load must be placed directly on the luggage rack. The vehicle's roof panel is not designed to carry a load. When loading the luggage rack, it is recommended to evenly distribute the load, as well as maintain a low center of gravity.
Page 156 Driving DRIVING THROUGH WATER Do not drive quickly through standing water, especially if the depth is unknown. Traction or brake capability may be limited and if the ignition system gets wet, your engine may stall. Water may also enter your engine's air intake and severely damage your engine.
Page 157: Roadside Emergencies
HAZARD LIGHTS CONTROL Use only in an emergency to warn traffic of vehicle breakdown, approaching danger, etc. The hazard flashers can be operated when the ignition is on or off. The hazard lights control is located on the instrument panel. Depress hazard lights control to activate all hazard flashers simultaneously.
Page 158 Roadside emergencies FUEL PUMP SHUT-OFF SWITCH After a collision, if the engine cranks but does not start, the fuel pump shut off switch may have been activated. The shut off switch is a device intended to stop the electric fuel pump when your vehicle has been involved in a substantial jolt.
Page 159 FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Always replace a fuse with one that has the specified amperage rating.
Page 160 Roadside emergencies Standard fuse amperage rating and color Color Passenger compartment fuse panel...
Page 161 Roadside emergencies The fuses and relays are coded as follows.
Page 162 Roadside emergencies Passenger compartment fuse panel...
Page 163 Roadside emergencies Passenger compartment fuse panel Relays in the passenger compartment fuse panel...
Page 164 Roadside emergencies Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high current fuses that protect your vehicle's main electrical systems from overloads. Always disconnect the battery before servicing high current fuses. Always replace the cover to the Power Distribution Box before reconnecting the battery...
Page 165 Roadside emergencies The high current fuses are coded as follows.
Page 166 Roadside emergencies Power distribution box...
Page 167 Relays in the power distribution box Relay Description Ignition Not used Not used Not used High beams Low beams Fuel pump Engine management Not used Not used Air conditioning Daytime running lights Fog lamps Not used Engine cooling fan level 2 (A/C) Engine cooling fan level 1 Roadside emergencies...
Page 168 Roadside emergencies CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. The temporary spare tire Your vehicle has a temporary spare tire.
Page 169 When driving with a temporary spare tire do not: exceed the maximum speed of 80 km/h (50 mph) under any circumstances load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label tow a trailer drive through an automatic car wash, because of the vehicle's reduced ground clearance try to repair the temporary spare...
Page 170 Roadside emergencies Tire change procedure To prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) to the tire being changed.
Page 171 Roadside emergencies 3. Remove the spare tire by loosening the tie down bolt in a counterclockwise direction. Take note of the jack position before removal in order to assist in restowing when finished. The jack can be removed by loosening the jack tie down bolt in the counterclockwise direction.
Page 172 Roadside emergencies 4. Remove the center cap or wheel cover. Loosen each wheel lug nut one half turn counterclockwise but do not remove them until the wheel is raised off the ground. 5. The vehicle jacking points are depicted on the yellow warning label on the jack shown here.
Page 173 In a heavily loaded vehicle condition and/or unusual emergency conditions such as the loss of the tire from the wheel rim, the vehicle may be resting so close to the ground that it may be difficult to insert the jack under the vehicle at the specified jacking location.
Page 174 Roadside emergencies...
Page 175 JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. You could damage the catalytic converter. Batteries contain sulfuric acid which burns skin, eyes, and clothing, if contacted.
Page 176 Roadside emergencies 3. Park the booster vehicle close to the hood of your disabled vehicle, making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts.
Page 177 Roadside emergencies 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle's engine, away from the battery.
Page 178 Roadside emergencies Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. 2.0 litre Zetec engine 2.0 litre SPI engine...
Page 179 Roadside emergencies 5. Be sure that the cables are clear of fan blades, belts and other moving parts of both engines. Jump starting 1. Start the engine of the booster vehicle and run the engine at a moderately increased speed. 2.
Page 180 Roadside emergencies 2. Remove the jumper cable on the negative (-) connection of the booster vehicle's battery. 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle's battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle's battery.
Page 181 It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. Roadside emergencies If your vehicle is to be towed from...
Page 182: Maintenance And Care
Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: We highlight do it yourself items in the engine compartment for easy location. We provide a Scheduled Maintenance Guide" which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service.
Page 183 Do not work on a vehicle with the engine running in an enclosed space, unless you are sure you have enough ventilation. Keep all lit cigarettes, open flames and other lit material away from the battery and all fuel related parts.
Page 184 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.0 SPI engine Power Engine oil steering fluid filler cap reservoir Engine coolant Engine oil reservoir dipstick (marked red and black) For ease of identification, most filler caps and the engine oil dipstick are marked yellow and black.
Page 185 IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.0 Zetec-E engine Power Engine oil steering fluid filler cap reservoir Engine coolant Engine oil reservoir dipstick (marked red and black) For ease of identification, most filler caps and the engine oil dipstick are marked yellow and black.
Page 186 Maintenance and care ENGINE OIL Checking the engine oil...
Page 187 Maintenance and care between the MIN and MAX marks between ADD and FULL DO NOT ADD Adding engine oil Checking the engine oil Make sure the oil level is not above the MAX mark or the FULL mark on the dipstick...
Page 188 Maintenance and care Engine oil and filter recommendations...
Page 189 Maintenance and care CLUTCH FLUID (if equipped) Check the clutch fluid level. Refer to the Scheduled Maintenance Guide" for the service interval schedules. The clutch master cylinder and brake master cylinder are part of the same system; both are refillable through the brake master cylinder with brake fluid.
Page 190 Maintenance and care Lubricant specifications Capacities and specifications Note:...
Page 191 WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. If the level is low, add enough fluid to fill the reservoir. In very cold weather, do not fill the reservoir all the way. Do not put engine coolant in the container for the windshield washer fluid.
Page 192 Maintenance and care If the engine coolant reservoir has become completely empty, have the engine cooling system inspected and refilled by a qualified service technician. Automotive fluids are not interchangeable; do not use engine coolant, antifreeze or windshield washer fluid outside of its specified function and vehicle location.
Page 193 Check the coolant level in the coolant reservoir the next few times you drive the vehicle. If necessary, add enough of a 50/50 mixture of coolant and water to bring the liquid level to the cold fill range on the reservoir. Never remove the coolant reservoir cap while the engine is running or hot.
Page 194 Maintenance and care For vehicles with green coolant Do not add orange coolant or recycled coolant to your vehicle originally equipped with conventional green coolant.
Page 195 Recycled engine coolant Ford Motor Company recommends that Ford dealers use recycled engine coolant produced by Ford approved processes. For vehicles with green coolant, not all coolant recycling processes produce coolant which meets Ford specification ESE M97B44 A, and use of such coolant may harm engine and cooling system components.
Page 196 Maintenance and care Severe winter climate What you should know about fail-safe cooling (2.0 L Zetec engines only)
Page 197 How fail-safe cooling works If the engine begins to overheat: the engine coolant temperature gauge will move to the red area. the Multi function warning light: automatic transaxle/ cooling system will illuminate. If the engine reaches a preset over temperature condition, the engine will automatically switch to alternating cylinder operation.
Page 198 Maintenance and care When fail-safe mode is activated You have limited engine power when in the fail safe mode, so drive the vehicle with caution. The vehicle will not be able to maintain high speed operation and the engine will run rough. Remember that the engine is capable of completely shutting down automatically to prevent engine...
Page 199 Maintenance and care CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the Scheduled Maintenance Guide" for the service interval schedules. If adding fluid is necessary, use only MERCON ATF. 1. The power steering fluid level should be checked before starting the engine.
Page 200 Maintenance and care TRANSAXLE FLUID Checking automatic transaxle fluid Refer to your "Scheduled Maintenance Guide" for scheduled intervals for fluid checks and changes. Your transaxle does not consume fluid. However, the fluid level should be checked if the transaxle is not working properly, i.
Page 201 Maintenance and care Low fluid level Correct fluid level...
Page 202 Maintenance and care High fluid level Fluid levels above the safe range may result in transaxle failure. An overfill condition of transaxle fluid may cause shift and/or engagement concerns and/or possible damage. High fluid levels can be caused by overheated or aerated fluid. This can be caused by operating for an extended period at high speeds, in city traffic during hot weather,...
Page 203 Maintenance and care BATTERY Your vehicle is equipped with a Motorcraft maintenance free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the Scheduled Maintenance Guide"...
Page 204 Maintenance and care If you see any corrosion on the battery cables or terminals, remove the cables from the terminals and clean with a wire brush. You can neutralize the acid with a solution of baking soda and water. Reinstall the cables when you are done cleaning them, and apply a small quantity of grease to the top of...
Page 205 When lifting a plastic cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.
Page 206 Maintenance and care 1. Set your parking brake. 2. Put the gearshift in P (Park) (automatic transaxle) or the neutral position (manual transaxle). Turn off all accessories and start the engine. 3. Let the engine idle for at least one minute. 4.
Page 207 Maintenance and care WINDSHIELD WIPER BLADES Change the wiper blades on your vehicle at least twice a year or when they seem less effective. Substances such as tree sap and some hot wax treatments used by commercial car washes reduce the effectiveness of wiper blades.
Page 208 Maintenance and care INFORMATION ABOUT TIRE QUALITY GRADES U.S. Department of Transportation Tire quality grades:...
Page 209 Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire grade 150 would wear one and one half (1 1/2) times as well on the government course as a tire grade 100.
Page 210 Maintenance and care Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 211 SERVICING YOUR TIRES Checking the tire pressure Use an accurate tire pressure gauge. Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles).
Page 212 (e.g., All Terrain", etc.), as originally offered by Ford. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over.
Page 213 SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all weather treads to provide traction in rain and snow. However, in some climates, you may need to use snow tires and chains.
Page 214 Maintenance and care Use only SAE Class S chains. Install chains securely, verifying that the chains do not touch any wiring, brake lines or fuel lines. Drive cautiously. If you hear the chains rub or bang against your vehicle, stop and re tighten the chains.
Page 215 WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. If you do not use the proper fuel cap, the pressure in the fuel tank can damage the fuel system or cause it to work improperly in a collision.
Page 216 Maintenance and care Observe the following guidelines when handling automotive fuel: Extinguish all smoking materials and any open flames before fueling your vehicle. Always turn off the vehicle before fueling. Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury.
Page 217 Fuels can also be harmful if absorbed through the skin. If fuel is splashed on the skin and/or clothing, promptly remove contaminated clothing and wash skin thoroughly with soap and water. Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation.
Page 218 Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If the fuel...
Page 219 Maintenance and care Choosing the right fuel Use only UNLEADED FUEL. The use of leaded fuel is prohibited by law and could damage your vehicle. Your vehicle was not designed to use fuel or fuel additives with metallic compounds, including manganese based compounds containing (MMT).
Page 220 Maintenance and care Octane recommendations (R+M)/2 METHOD Fuel quality...
Page 221 They could cause damage to the fuel system that may not be covered by your warranty. Cleaner air Ford approves the use of gasolines to improve air quality, including reformulated gasolines that contain oxygenates up to 10% ethanol or 15% MTBE.
Page 222 Maintenance and care Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on modern powertrain components. If you have run out of fuel: You may need to crank the engine several times before the system starts to pump fuel from the tank to the engine.
Page 223 Maintenance and care ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques...
Page 224 Maintenance and care The amount of Empty Reserve varies and should not be relied upon to increase driving range. When refueling your vehicle after the fuel gauge indicates empty, you might not be able to refuel the full amount of the advertised capacity of the fuel tank due to the empty reserve still present in the tank.
Page 225 Maintenance and care Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading. 2. Each time you fill the tank, record the amount of fuel added (in liters or gallons). 3. After at least three to five tank fill ups, fill the fuel tank and record the current kilometer (mileage) reading.
Page 226 Maintenance and care Driving style – good driving and fuel economy habits Give consideration to the lists that follow and you may be able to change a number of variables and improve your fuel economy. Habits Smooth, moderate operation can yield up to 10% savings in fuel.
Page 227 Use of speed control (if equipped) can improve fuel economy. Speed control can help maintain a constant speed and reduce speed changes. You may want to turn off the speed control in hilly terrain as unnecessary shifting between third and fourth gears may occur causing deterioration in fuel economy.
Page 228 Maintenance and care Conditions Heavily loading a vehicle or towing a trailer will sharply deteriorate fuel economy at any speed. Carrying unnecessary weight will deteriorate fuel economy (approximately 0.4 l/100 km [1 mpg] is lost for every 180 kg [400 lb] of weight carried). Adding certain accessories to your vehicle (for example bug deflectors, rollover/light bars,...
Page 229 Maintenance and care EPA window sticker Every new vehicle should have the EPA window sticker. Contact your dealer if the window sticker is not supplied with your vehicle. The EPA window sticker should be your guide for the fuel economy comparisons with other vehicles.
Page 230 Scheduled Maintenance Guide" are essential to the life and performance of your vehicle and to its emissions system. If other than Ford, Motorcraft or Ford authorized parts are used for maintenance replacements or for service of components affecting...
Page 231 Illumination of the Charging system warning light, Check engine light or a high engine temperature, fluid leaks, strange odors, smoke or loss of oil pressure, could indicate that the emission control system is not working properly. Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment.
Page 232 Maintenance and care Readiness for inspection/ maintenance (I/M) testing Check engine Warning Lights and Chimes Instrumentation Check engine...
Page 233 EXTERIOR BULBS Replacing exterior bulbs Check the operation of the following lamps frequently: Headlamps Tail lamps Brakelamps High mounted brakelamp Turn signals Backup lamps License plate lamp Do not remove lamp bulbs unless they will be replaced immediately. If a bulb is removed for an extended period of time, contaminants may enter the lamp housings and affect performance.
Page 234 Maintenance and care To remove the headlamp bulb: 1. Make sure that the headlamp control is in OFF position. 2. Open the hood. 3. Rotate the bulb cover counterclockwise and remove. 4. Swivel the wire clip to the side and pull out the lamp. 5.
Page 235 Maintenance and care 3. Pull the bulb straight out of the socket and push in the new bulb. 4. Install the bulb socket in grille by turning clockwise. Replacing foglamp bulbs 1. Reach under the bumper cover and remove the bulb socket from the foglamp by turning counterclockwise.
Page 236 Maintenance and care Replacing tail/brake/backup lights and turn signal bulbs (Coupe) 1. Open the tailgate. 2. From inside the luggage compartment remove the wing nut of the rear light assembly cover. 3. Using a Phillips screw driver remove the screw. The lamp is still retained by a spring loaded clip.
Page 237 Maintenance and care Replacing tail/brake/backup lights and turn signal bulbs (Sedan) 1. Open the tailgate. 2. From inside the luggage compartment remove the three wing nuts of the light housing. 3. Gently pull the light housing to the outside. 4. Turn the bulb socket counterclockwise and pull out the socket.
Page 238 Maintenance and care Replacing tail/brake/backup lights and turn signal bulbs (Wagon) 1. Open the tailgate. 2. With a screw driver remove the fixings and trim from the body. 3. Remove the socket from the lamp assembly. 4. Pull the bulb straight out of the socket and push in the new bulb.
Page 239 Maintenance and care High-mount brake lamp bulbs Open the luggage compartment. With a screw driver remove the fixings and trim from the tailgate. Pull the bulb holder from the lamp assembly. Pull the bulb out. Install in reverse order. Replacing interior lights Switch off the interior lights (middle switch position).
Page 240 Maintenance and care Luggage compartment light Using the right bulbs Function Trade number...
Page 241 Maintenance and care AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by a qualified service technician. Vertical aim adjustment 1.
Page 242 Maintenance and care...
Page 243 Maintenance and care CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer assistance chapter for a list of Ford approved cleaners, polishes and waxes. Washing your vehicle Wash your vehicle regularly with cold or lukewarm water. Never use strong detergents or soap. If your vehicle is particularly dirty, use a quality car wash detergent.
Page 244 Repairing paint chips Minor scratches or paint damage from road debris may be repaired with touch up paint, repair foil or aerosol paint spray from the Ford accessories line. Observe the application instructions on the products. Remove particles such as bird...
Page 245 Maintenance and care Cleaning the wheels Wash with the same detergent as the body of your vehicle. Do not use acid based or alcohol based wheel cleaners, steel wool, fuel or strong detergents. Never use abrasives that will damage the finish of special wheel surfaces.
Page 246 Maintenance and care Cleaning the wiper blades If the wiper blades do not wipe properly, clean the wiper blade rubber element with undiluted windshield wiper solution or a mild detergent. To avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents.
Page 247 Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth. Avoid cleaner or polish that increases the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection.
Page 248 Maintenance and care Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended for cleaning upholstery or carpets. Do not bleach or dye the belts, because these actions may weaken the belt webbing. Check the safety belt system periodically to make sure there are no nicks, wear or cuts.
Page 249 Maintenance and care The type of scrubbing pad is very critical because the common 3M Scotch Brite" green pad is too aggressive and will damage the leather surface.
Page 250 Maintenance and care Do not use household cleaners, glass cleaner, alcohol solutions or cleaner intended for vinyl, rubber or plastics. These products can damage the leather. In some instances, color or dye transfer can occur when wet clothing (wool, denim, leathers or other non colorfast garments) comes in contact with leather upholstery.
Page 251 Maintenance and care Woodtone trim Wipe stains with a soft cloth and a multi purpose cleaning solution. Inside windows Use glass cleaner for the inside windows if they become fogged. Cleaning mirrors Do not clean your mirrors with a dry cloth or abrasive materials. Use a soft cloth and mild detergents and water.
Page 252: Capacities And Specifications
Capacities and specifications MOTORCRAFT PART NUMBERS 2.0L Zetec-E Component 2.0L SPI engine engine...
Page 253 Capacities and specifications REFILL CAPACITIES Fluid Ford part name Application Capacity Lubricant specifications...
Page 254 Capacities and specifications LUBRICANT SPECIFICATIONS Ford part name or Item equivalent Ford part Ford number specification...
Page 255 Capacities and specifications ENGINE DATA 2.0L Zetec-E Engine 2.0L SPI engine engine...
Page 256 Capacities and specifications Sedan VEHICLE DIMENSIONS Dimensions (1) Overall length (2) Overall width (3) Overall height (4) Wheelbase (5) Track 4362-4369 (171.7-172) 1440-1481 (56.7-58.3) front 1484-1502 (58.4-59.1) rear 1477-1495 (58.1-58.9) mm (in) 1998 (78.7) 2615 (103)
Page 257 Coupe Dimensions (1) Overall length (2) Overall width (3) Overall height (4) Wheelbase (5) Track Capacities and specifications 4150-4178 (163.3-164.5) 1440-1481 (56.7-58.3) front 1484-1502 (58.4-59.1) rear 1477-1495 (58.1-58.9) mm (in) 1998 (78.7) 2615 (103)
Page 258 Capacities and specifications Wagon Dimensions (1) Overall length (2) Overall width (3a) Overall height (w/o roofrack) (3b) Overall height (with roofrack) (4) Wheelbase (5) Track 4438-4465 (174.7-175.8) 1492-1532 (58.7-60.3) 1451-1491 (57.1-58.7) front 1484-1502 (58.4-59.1) rear 1477-1495 (58.1-58.9) mm (in) 1998 (78.7) 2615 (103)
Page 259 Capacities and specifications IDENTIFYING YOUR VEHICLE Safety compliance label The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the front door latch pillar on the driver's side.
Page 260 Capacities and specifications Vehicle identification number The vehicle identification number (VIN) is attached to a metal tag and is located on the driver side instrument panel. The VIN tag may be seen by looking through the windshield from outside the vehicle.
Page 261: Customer Assistance
Customer assistance GETTING ROADSIDE Using roadside assistance ASSISTANCE...
Page 262 Customer assistance Ford extended service plan...
Page 263 Customer assistance Getting the service you need Away from home At home...
Page 264 Customer assistance THE DISPUTE SETTLEMENT BOARD (U.S. only) What kinds of cases does the Board review?
Page 265 Customer assistance Board membership What the Board needs...
Page 266 Customer assistance Oral presentations Making a decision...
Page 267 Customer assistance To request a DSB brochure/application UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY)
Page 268 Customer assistance GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADA...
Page 269 FORD ACCESSORIES FOR YOUR VEHICLE Customer assistance Not all accessories are available for all models.
Page 270 Customer assistance Vehicle Security Comfort and convenience Travel equipment Protection and appearance equipment...
Page 271 Customer assistance ORDERING ADDITIONAL OWNER’S LITERATURE For a free publication catalog, order toll free: 1 800 782 4356...
Page 272: Reporting Safety Defects (U. S. Only)
Reporting safety defects REPORTING SAFETY DEFECTS (U.S. ONLY)
Page 273: Index
ABS warning lamp ... Accessories ....Adding brake fluid ... Adding engine coolant Adding washer fluid Additives, engine oil...
Page 274 Index Page Page...
Page 275 Page Index Page...
Page 276 Index Page Page...
Page 277 Radio ..... . . Reading lamps ....Rear window defroster Recycled engine coolant Refill capacities...
Page 278 Index Tachometer ....Temperature control Temperature gauge Tilt steering wheel ... . Tires, changing .
Page 280: Filling Station Information
Filling station information Item Information Lubricant Specifications.

Ford 2000 Focus Owner's Manual

Quick Links

Related Manuals for Ford 2000 Focus

Summary of Contents for Ford 2000 Focus

Table of Contents